Godrej Forte Pro 15 Litres Digital Electronic Safe Locker User Manual

All about securing valuables and peace of mind for you.
The User Manual Digital & Biometric

Forte Pro 15 Litres Digital Electronic Safe Locker

Safety of your valuables becomes paramount in today’s fast paced and highly uncertain times. Precisely the reason we, at Godrej Security Solutions, have a range of Home Lockers that take care of your exact safety requirements. What’s more, these lockers are 10X stronger and come with various cutting-edge safety features like Ultra Key, Digital or Biometric locking. Plus, you also get to choose the size of the locker that suit your needs, and then sit back and relax with  the knowledge that your valuables are safe in a Godrej Home Locker.

Digital

| 10X Stronger*
---|---
| Motorised lock for enhanced safety
| USB & Key or emergency access
| Anchoring provision for installation

Package contents

Important instructions (to be missed at your own risk)

The locker is in Home Mode by default. To change the locker from Home mode to Hotel mode and vice verse, please follow instructions on the page number 12 in Section e (6th Digit) Operational mode.
Make sure the Locker is anchored properly as it can fall and hurt people and property.
Please keep this manual and override keys in a safe place (NOT INSIDE THE LOCKER).
DO NOT use any liquid while cleaning the keypad/ fascia. You could use a damp cloth if required.
DO NOT place any liquid on top of the locker, a spill on the keypad/fascia may render the locker inoperable.
DO NOT overstuff the locker or you can damage the motor mechanism or the contents.
For security purposes, you should change the factory default code i.e.
Personal Code and Master Code as soon as possible. Godrej Security
Solutions shall not be responsible for any theft caused by such negligence.
DO NOT open the back cover or try to repair the locker yourself. In case of any problem contact our Call Center at 1800 20 999 55.

Know your product

Home mode operation

To open the locker: Enter the personal code. When the display shows “OPEN”, the bolts will retract automatically. The display will show “OPENED” after the bolts have fully retracted.
Now, open the door by pulling from the bottom of the keypad.
To lock the locker: Close the door and press # button. The display will show “CLOSE”, the bolts will extend automatically. After the bolts have fully extended, the display will show “CLOSED”.
Note: The Master code can only be used to unlock the locker.

How to change the personal code in Home mode

1. Open the locker.
2. Press * twice and the display will show “PROG”.
3. Press ‘68 #’ and the display will show “NEU”.
4. Enter the new code and press #. That will Close the Locker.
   Note: Default Personal Code is “1234”.

Hotel mode operation

To open the locker: Enter the personal code which was entered while locking the locker. The factory default personal code is “1234”. When the display shows “OPEN”, the bolts will retract automatically. After the bolts have fully retracted,  the display will show “OPENED”. Now, open the door by pulling from the bottom of the keypad.
To lock the locker: First, close the door and enter personal code and press # button. When the display will show “CLOSE”, the bolts will extend automatically. The display will show “CLOSED” after the bolts have fully extended.
Note: The Master code can only be used to unlock the locker.

WARNING: In Hotel mode, you can unlock the locker only with the personal code entered during the last locking operation.
The Locker will go on auto freeze mode, locking itself for 15 min. in case of consecutively 4 times of wrong password input. The duration time of locking can be set as per requirement.

How to change the personal code in Hotel mode
In Hotel Mode, every time you close the locker, you can enter a new personal code and press #. The locker will open with the last entered personal code only.

Trick to change the Master code

Master code is available for unlocking in case the user code is forgotten.

1. Open the locker.

2. Press * twice and the display will show “PROG”. Then, enter the original Master code. The factory set Master code is 800000.
   The display will now show “NEU”.

3. Next, Enter the 6 digit code of your choice. The display show “AGAIN”. Now, enter the code again and press # key to confirm.

4. The display will show “DONE” to indicate that the new Master code has been set up successfully.

WARNING: For security purposes, you should change the factory default code as soon as possible. Godrej Security Solutions shall not be responsible for theft caused by such negligence. Do not use Function code for the new Master code (EX:751019)

Stop your code from being displayed and compromise security

1. First, Open the locker using your Personal Code.
2. Press * twice and the display will show “PROG”.
3. When “PROG” disappears, press 751019 within 5 seconds.
4. 171300 will appear. Now, with the first digit flashing press (0) then press # once. The display will go blank.
5. Close the locker (you will have to press your personal code to lock the door).
6. Check if this feature is activated by entering Personal Code, You will see that “—” appears instead of your personal code.

Hot key – viewing/not viewing password while keying in
If your lock is set so that your code appears every time and you do not want it to appear for that one time, you can press (0) then # key before your code. Only dashes will appear for that one time. The next time you press your code, it will appear as usual.
Likewise, if your lock is set so that your code never appears, you can simply press (9) then # and your code will appear for that one time only.
This function applies to both modes (Home Mode & Hotel Mode).

Testing the battery level

Test battery level:
You can test the Battery levels either with the door opened or closed.

• Press # key.
• The display will show “bA-HI” or “bA-LO”.
• “bA-LO” means that you need to replace the batteries.

Simple program to access the programming

• Open the locker
• Press * twice, the display will show “PROG”
• Press 751019 while the word “PROG” disappears
• The current setup will appear with the first digit flashing
• All 6 sections must be entered within 10 seconds. You can change one or more sections, but all 6 sections must be entered. To keep a section programmed as it is currently set, simply press the same numbers that are currently displayed for that section and press #.
• The display will go blank

To set up the different features listed below, you must first decide how you want the locker to function.
Section a (1st Digit) Code appearance on display
Press 0: If you DO NOT want your code to appear on the display (only dashes will appear) with beep sound when you press each key button (Default).
Press 1: If you want your code to appear each time you press your code and then flash for verification one time, with beep sound when you press each key button.
Press 2: If you want your code to appear each time you press your code, with beep sound when you press each button.
Section b (2nd Digit) Preferred number of digits in your code
Personal code can be 4-6 digits.
Press 4: To use a 4-digit code.
Press 5: To use a 5-digit code.
Press 6: To use a 6-digit code.
Press 7: To choose the length of code (4-6 digits) when you set the code (Default).
Section c (3rd Digit) Lockout delay
If the wrong code is entered 4 times in a row, the touch pad will shut down for a length of time that you set.
This is to deter someone from opening your locker by keying in a random number.
You must pick one of these three options:
Press 0: For no lockout delay.
Press 1: For a 15 minute delay (Default).
Press 2: For a 30 minute delay.
Press 1: For a 15 minute delay (Default).
Press 2: For a 30 minute delay.
Section d (4th Digit) Master code
The Master code will open the locker if you happen to lose the code and override keys. The Master code is preset at the factory.
Press 2: To turn OFF the Master code feature.
Press 3: To turn ON the Master code feature (Default).
Section e (6th Digit) Operational mode
This feature allows you to change how the locker operates, either for Home mode or Hotel mode.
Press 0: To set for Home Mode (Default).
Press 1: To set for Hotel Mode.
Press # once to exit Program Mode.

In case of emergency use the override key

1. Open the keyhole.
2. Use one of the override keys and insert it into the cylinder. Turn anti-clockwise to open the locker.
3. While the door is open and the key is still turned, follow the instructions to set your personal code.

Note: When you set the new personal code, rotate the key to the locked position, so that it can be removed. If you get an error message, wait until the motor stops moving and then turn the key back to locked position and remove it. Your  new personal code will still remain.
WARNING: Keep the override keys in a safe place other than inside the locker. These keys are to be used in case of emergency.

USB access – Technology always helps

In case of low battery, a regular USB wire connected to a power bank can be inserted in the slot available on the lock panel. This will energise the locker by using power from the USB source*. The user can then enter the code, unlock the  locker and replace the battery.

Free yourself from the error messages

Listed below are error codes that you might encounter:
This means that you have pressed an incorrect personal code. You need to Verify your personal code and try again. If you get this error four times consecutively, the keypad will lock out for 0/15/30 minutes.
This means that the locker has entered the lockout period. You will not be able to open the locker during the lockout period. However, by pressing any key during this period you can see how much time is left until the lockout is over. If  your personal code still doesn’t work, use the override keys to reset the locker. (see “TO ACCESS THE PROGRAMMING” section 3)
This means that the bolts have failed to retract fully. To rectify the error, Press the door towards the inside while entering your personal code. If you still cannot open your locker, then contact GSS Call
Center on 1800 20 999 55 or write to us at secure@godrej.com.
This could also mean that the bolts have failed to extend fully. This may happen because the locker is too full. To correct the error, Press the door to close it fully while pressing your personal code. If you still cannot close your locker then contact the GSS Call Center on 1800 20 999 55 and consider it done.

1800 209 9955
Installation helpline
SECURITY SOLUTION
Godrej Security Solutions, Plant No.17,
Pirojshanagar, Vikhroli, Mumbai – 400079.
secure@godrej.com www.godrejsecure.com

References

• Welcome to the World of Godrej
• India's Leading Locks & Security Security Solutions |Security Locks, Safes, Lockers and more|Godrej & Boyce

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>