QFX J-220BT Boombox MP3 Conversion from Radio Instruction Manual

June 14, 2024
QFX

QFX J-220BT Boombox MP3 Conversion from Radio

QFX J-220BT Boombox MP3 Conversion from Radio

Introduction

PLEASE MAKE SURE THE VOLTAGE SWITCH INSIDE THE BATTERY COMPARTMENT ‘8 SET TO THE AC VOLTAGE OF THE COUNTRY YOU ARE CURRENTLY USING THE STEREO IN.

J-220BT FUNCTIONS

  1. Telescope Antenna

  2. Handle

  3. Tape & Radio USB Switch

  4. Band Selector

  5. External Earphone Jack

  6. Mic.

  7. Tuning Knob

  8. Volume Control Knob

  9. Pause Button (Back)

  10. Stop Button

  11. Fast Forward Button

  12. REW Button

  13. Play Back Button

  14. REC Button

  15. Loud Speaker

  16. DC Jack

  17. Cassette Compartment

  18. AC Socket

  19. Battery Compartment

  20. 3 Band Equalizer

  21. USB Slot

  22. SD Slot

  23. USB/SD:REC/PLAY/PAUSE Button

  24. USB/SD:REC/DELETE Button

  25. USB/SD: REW Button

  26. USB/SD: Fast Forward Button

  27. REC/MP3 Play Indicator
    J-220BT Function

  28. Locate the voltage switch found In the battery compartment. Check the lower right comer for voltage position.

  29. Use a thin tool to toggle the switch to the prop9’voltage position (110V or 220V).
    J-220BT Function

QUICK START GUIDE

6 – STEP SETUP GUIDE

  • Step 1 Find the AC power cord to the J-220BT located on the back panel of the unit.
  • Step 2 Find a power outlet (AC 120V/60Hz) and connect the AC cord to the socket to supply the unit with power.
  • Step 3 Move to the top of part of the panel and set the switch to USB.
  • Step 4 Insert a USB flash drive in the USB port located below the cassette compartment. The J-220BT will automatically begin playing the .mp3 content.
  • Step 5 Use the Knob to adjust the Master Volume to your taste.
  • Step 6 Press the Forward and Rewind keys to move to the next track or previous track.
    Step Setup Guide

Bluetooth MP3 Instructions

Set the function switch to the MP3/BT position. After hearing the Bluetooth prompting sound, open the Bluetooth settings on your mobile device and search lot the J-220BT. Select the option to connect. You will then hear a sound and see a light flash. Now you can select music from your favorite music app.

USB/SD Card :
Insert a USB/SD Card in the corresponding port for music playback. The content will begin playing automatically. Use the Forward and Rewind functions on the unit to navigate through the .mp3 music.

Recording Function :
Radio Recording: Set the function switch to the RADIO position and select the desired station.
Insert a USB or SD Card into the device, then press the “REC/DEL” button to start recording.
The REC/MP3 PLAY light will turn ON. If you want to exit the recording, press the “REC/DEL” button again. Record a cassete tape, radio station, or voice using the built-in microphone to the USB or SD Card.

WARNING

IMPORTANT SAFETY MEASURES

Before using this machine, please read all the safety and operating instructions. These safety and operating instructions should be kept in condition of consultation.
Safety Precaution

  1. Electric Power Supply Line : Keep the power cord safe from being trampled on, pressed on by heavy objects, or pierced. Make sure that the cord has ample space to rest on the ground and is not stressed. DO NOT pull or drag or the power supply line.
  2. Ventilation : This unit must be set in a ventilated space. DO NOT cover the vents on the back panel for any reason. If placed alongside a wall, distance the unit a minimum of 1 Dem to allow air flow. DO NOT surface that might restricted good air flow.
  3. Dismantling : DO NOT dismantle or open the unit. This is a high-powered unit that can cause serious harm if tampered with. DO NOT Open.
  4. Smoke : Please unplug the power supplies cord from the wall outlet immediately if unusual smoke appears and contact customer support.
  5. Please make sure the voltage switch inside battery compartment is set to the AC voltage of the country you are using the stereo.

Question? Comments? Contact Us Anytime

1-800-864-CLUB (2582) Mon-Fri 9AM-WM(PST)

support@qfxusa.com
Mon-Fri 9AM • 5PM (PST)

WARNING!

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER ON THIS SPEAKER THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN
To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this product near any liquids, heat sources such as radiators, heat registers or under extreme weather conditions. Clean only with a dry cloth.
Users should exhibit extra safety when the WARNING or CAUTION symbol appears in this instruction manual and follow all precautions as they are stated.

BASIC OPERATION

AC Operation

  1. Before connecting the unit to an AC outlet, check the operating VOLTAGE of the unit is identical with the VOLTAGE of your local power supply.
  2. Connect the supplied AC power cord to the AC socket at the back of unit.
  3. The battery will be automatically disconnected when the AC Power cord is plugged into the socket.

Battery Operation
Unplug the AC cord from AC jack. This unit requires UM IX4 (not included), open battery insert the batteries in the battery compartment at the downside of the unit, be careful of position according to the notes. Close the battery cover.

Radio Operation

  1. Select required band (FM/ AM/SW1 -SW2) with BAND selector
  2. Select desired station by rotating the TUNING control
  3. The built-in antenna is directional. When receiving FM or SW-1-SW-2 broadcast, pull out the telescopic antenna in full length; the strongest reception can be achieved by rotating and searching for the strongest signal.
  4. Adjust VOLUME control to your listening preference.
  5. To turn off the radio, set the function selector to TAPE (OFF} button. Listen with headphones (not included).\For private listening, you can use headphones with the unit. Connect the headphones (not included) to the headphone jack at the side of the unit. The sound from the speakers automatically turn off when headphones are connected to the unit.

Playback Operation
Cassette Play

  1. Set the function selector to the TAPE position
  2. Press the STOP/EJECT button to open the cassette door. Insert the cassette so the open side faces up. Close the cassette door.
  3. Use the following buttons and controls for cassette play:

PLAY :
Press Play to begin playing the cassette tape
F.FWD :
Press to rapidly advance the cassette tape forward.
REWIND :
Press to rapidly rewind the cassette tape back.
STOP :
Stop playing or release the F.FWD and REW button.
AUTO STOP :
Cassette tape will automatically stop when it reaches the end.
PAUSE :
Press to stop playing or recording. The use of the PAUSE button does not disturb the setting for either play or record. This function should be used for a temporary stop. It is best to use the pause button when recording. Press PAUSE again to resume playing back or recording.
VOLUME CONTROL :
Slide the control to the right to increase the volume. Slide the control to the left to decrease the volume.

Directly Recording from the Radio

  1. Set the function selector to the radio position.
  2. Turn ON the radio station you want to record.
  3. Insert a blank cassette into the tape compartment.
  4. Press the Record and Play button to begin recording.
  5. Press the Stop button to end the recording or press the pause button to pause the recording.

Care and Maintenance
To ensure optimum performance from your unit, keep the tape inside clean. To clean the tape path, open the cassette door. Moisten a cotton swab with isopropyl alcohol or special tape head cleaning fluid. Remove any excess alcohol from the swab. Clean the tape head, capstan and pinch roller. Avoid scratching the head surface. To clean the unit housing, use a soft damp cloth. After cleaning, wipe the unit surface with a dry cloth.
CAUTION : Never use chemicals such as benzene or paint thinner for cleaning.
Care and Maintenance

Keep magnets and metallic objects away from the tape head. If the head becomes magnetized, noise will increase and the volume tone will deteriorate and possibly cause damage.

TROUBLESHOOTING
If the Cassette tape fails to move, you get poor reception, or fluctuating volume, try replacing the batteries or connect the unit to a power source.

Radio to Tape Recording :

  1. Set the function selector to the radio position.
  2. Turn ON the radio station you want to record.
  3. Insert a blank cassette into the tape compartment.
  4. Press the Record and Play button to begin recording.
  5. Press the Stop button to end the recording or press the pause button to pause the.

Tape to .mp3 Recording :
Set the function switch to TAPE and insert your music cassette tape. Insert a USB or SD Card and wait for the REC/MP3 light to turn on and the press the REC button. Press play on the cassette tape to begin the .mp3 conversion. The J-220BT converts at a resolution of 128Kbps.

Follow Us

Social Media Icons

Logo

Documents / Resources

| QFX J-220BT Boombox MP3 Conversion from Radio [pdf] Instruction Manual
J-220BT Boombox MP3 Conversion from Radio, J-220BT, Boombox MP3 Conversion from Radio, MP3 Conversion from Radio, Conversion from Radio, Radio
---|---

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals