ErGear EGESD5B-4 Electric Standing Desk with Full Size Keyboard Tray Instruction Manual

**ErGear EGESD5B-4 Electric Standing Desk with Full Size Keyboard Tray Instruction Manual

**

Tools Needed (Not included)

• Drill

• Phillips Screwdriver

Specifications

Height Adjustment Range 28.3”–46.5” (72-118cm)

• Power Input 100V-240V

• Max. Speed 20mm/s

• Operating Noise <55dB

• Max. Load 176 lbs / 80 kg

Step 1
Supplied Parts and Hardware

• Crossbar

• Left Desk Leg

• Right Desk Leg

• Leg Base

• Bolt M6 x 11mm

• Bolt M6 x 35mm

• Large Allen Wrench 3/16” (5mm)

Step 2

• Side Plate Bolt M

• Transmission Rod
  

• Bolt M6 x 11mm

• Large Allen Wrench 3/16” (5mm)

• Small Allen Wrench 5/64” (2mm)

• • Rubber Pad

Step 3

• Desktop

• ScrewM5 X 16mm

• Wood Dowel Pin

• Desktop Panel Connector

• Storage Hook

• Controller

Step 4

• Keyboard Tray

• Keyboard Stopper

• Wrist Rest

• Left Keyboard Tray Side Plate

• Right Keyboard Tray Side Plate

• Screw M4 X 6mm

• Screw M5 X 16mm

Step 5

• AC Adapter
  

• Cable Clip

Step 1

Assembling and Connecting the Desk Legs

Step 2

Attaching the Side Plates and the Transmission Rod

Loosen the coupling nut.

Before attaching the transmission rod, measure the heights of the two desk legs to serif they are set at the same level. If not, insert the trans mission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level   with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

Tighten the coupling nut to fine-tune transmission rod fit.

Step 3

Assembling and Attaching the Desktop

• Assemble the desktop
  

• Drill (not included)

• Phillips Screwdriver (not included)

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

• Attach the desktop to the frame.
  

• Attach the controller and hooks to the desktop.
  

Step 4

Assembling and Attaching the Keyboard Tray

• Attach the stopper to the keyboard tray.
  

You can use a drill (with suitable torque and speed)  or a Phillips screwdriver.

• Drill (not included)

• Phillips Screwdriver (not included)

• Attach the wrist rest to the keyboard tray.
  

• Pull out the inner parts of the drawer slides a little for easier keyboard tray alignment. Then align and insert the tray.
  

• Attach the assembled keyboard tray to the desk. You can use a Phillips screwdriver instead of a drill for  easier access to screw in the screws.
  

Step 5

Connecting the Cables

Using the Controller

• Save Current Height Setting
  Short-press the button, and the display will flash. Press the , , or button to save the current height setting to that button.

• Select Height Setting 1
  Press the button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released.

• Lower the Desk
  Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Change Display Height Units| Press and hold the button until a flashing ‘S-’ is displayed. Press  again, and ‘Un’ is displayed. Press  to select it, press  or  to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press  to save your choice.
---|---
Change Collision Force Detection| Long press the  button, ‘S-‘ shows and flashes. Press  again and the display shows ‘Un‘. Press   or   to switch to ‘CF‘. Press   to select. Press  or to switch between ‘OFF‘, Low (L), Normal (n) or Heavy (H) collision force detection. Press  to save your choice.
Reset| Press and hold the  button for 5 seconds, and the screen will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.
Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
E10| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)

Other Info
support@ergear.com

Website
https://ergear.com

References

• Complete Flexibility. Total Freedom – ErGear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>