SALTA HB-103SC-S2 Ultra Stick Hand Blender Instruction Manual

MULTI-PURPOSE
Ultra-Stick
HAND BLENDER
HB-103SC-S2
Instruction Manual

Read instructions carefully before operating the unit.

Hand Blender

Important Hints
Read this instruction manual carefully before operating this unit.

Meaning of crossed —out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact you local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.

Important Caution

Check each accessory carefully before using this unit.

• This appliance is not intended for use by persons {including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Before using this unit, check the mains power voltage corresponds to the voltage shown on the marking plate.
• Always disconnect the blender from the supply if it is left unattended and before assembling, disassembling or cleaning
• Do not allow children to use the blender without supervision
• Do not switch the appliance on if it appears to be faulty in any way.
• For repairs, accessories or power cord replacement, contact your dealer or an authorized Service Center.
• It is not allowed to immerse the base into water for cleaning and it is forbidden to start the unit or press the control button by wet hands.
• The water temperature should not be over 60°C when cleaning the unit.
• Do not run this unit long-time, otherwise the inner parts will be damaged.
• When the motor is running, do not insert your finger or other objects into the machine and container.
• If the supply cord is damaged, it must be replaced by the manufacturer. Its service agent or similarly qualified persons if order to avoid a hazard.
• Only use this appliance and the provided accessories. Use the appliance for its intended purposes only. Do not use the appliance and the accessories for other purpose than described in this user instruction manual.
• Care shall be taken when handling the sharp cutting blades, emptying the container and during cleaning. Do not try to use the cutting blade or accessory other than the correct purpose to prevent dangers. Misuse or assemble the cutting blade or accessory will cause dangers.

Name of Part

Technical parameter

content/uploads/2022/05/Screenshot_3-305.png)
Rated working time| ≤1min| Rated Interval Time| ≥1 min

OPERATION GUIDE

Using Blender
The hand blender is perfectly suited for preparing dips. sauces. mayonnaise and baby food as well as for mixing and milkshakes.

1. Insert the blender bar into motor unit. turn clockwise to lock it into motor unit.

2. Put ingredients in the beaker, to prevent splattering. immerse the blade guard completely in the ingredients. You can use the hand blender in the beaker and just as well in any other vessel
   

3. Switch the appliance on by pressing the turbo or switch.

4. Speed regutation switch can use speed control knob

5. Blend the ingredients by moving the appliance slowly up, down and in circles.

Using chopper
The chopper is perfectly suited for hard food, such as chopping meat, cheese, onion, herbs, garlic, carrots, walnuts, almonds, prunes etc.
CAUTION: Don’t chop extremely hard food, such as ice cubes, nutmeg; coffee beans and grains. The blades are very sharp! Be very careful when handing the blade unit.

1. Put the chopper blade unit in the chopper bowl. press down the blade unit and lock bowl.

2. Put the ingredients in the chopper bowl, solid ingredients should not be larger than 2cm pieces.

3. Put the chopper coupling unit onto the chopper bowl.

4. Fasten the motor unit onto the chopper bowl, Installation reference“using blender”.

5. Switch the appliance on by pressing the turbo or switch.

Using whisk
The whisk is intended for whipping cream, beating egg whites and mixing sponges and Ready-mix desserts.

1. Insert the whisk into the Whisk coupling unit strongly.
2. Connect the coupling unit to the motor unit, installation reference“using blender’.
3. Press the switch to activate the handie blender, and press the turbo after approx 30 seconds to prevent ingredients splashing.

Using milk frother
The whisk is intended for whipping cream and froth milk., froth all types of milk, create a vast array of professional-quality hot and cold foam and drinks such as cappuccino, latte, hot chocolate, milkshake, cocktails (and many more).

1. Insert the frother into the Whisk coupling unit strongly.
2. Connect the coupling unit to the motor unit, installation reference“using blender’.

CLEANING AND MAINTENANCE

1. Before cleaning, unplug the appliance and detach the accessories.
2. Wipe the motor unit, the chopper coupling unit, the whisk coupling unit with a moist cloth, do not immerse them in water. Other accessories can put the dishwasher or the water clean.
3. If food is not easily rinsed off the blade or whisk, place a drop of dish detergent in the mixing container with water. Plug cord into outlet. Immerse the blade end portion or whisk and operate the unit for about 10 seconds. Unplug. rinse under running water, and then dry.
4. When will not use long time. keep this appliance well ventilated at the aridity of place to prevent the motor of appliance is affected with damp.

CAUTION:
The cutting edges of the blades are very sharp, cleaning it must be carefully.

TIPS

Whisk Attachment

1. Insert the Whisk attachment into the Gearbox.
   Push hard inward, Until the parts locked into the gearbox

2. Then insert the Gearbox into the motor body and turn it counterclockwise so that it snaps into the motor body housing.

• To disassemble, turn the Gearbox clockwise and detach it from the Whisk.

Milk Frother Attachment

1. Insert the Milk Frother attachment into the Gearbox.
   Push hard inward, Until the parts locked into the gearbox

2. Then insert the Gearbox into the motor body and turn it counterclockwise so that it snaps into the motor body housing.
   – To disassemble, turn the Gearbox clockwise and detach it from the Milk Frother.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>