Smallrig RC220B LED Video Light User Manual
- June 14, 2024
- SmallRig
Table of Contents
Smallrig RC220B LED Video Light
Foreword
Thank you for choosing SmallRig RC220B LED Video Light.
Warnings
- Please read this User Manual carefully.
- Keep this User Manual and always include it when passing the product onto the third party.
- Heed all warnings and follow all instructions in this User Manual.
- Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.
- Care must be taken as burns can occur from touching hot surfaces
- Do not operate the fixture if a cord is damaged or if the fixture has been dropped or damaged until it has been examined by qualified service personnel.
- Position any power cables so that they will not be tripped over, pulled or put into contact with hot surfaces.
- If an extension cord is necessary, a cord with an amperage rating at least equal to that of the fixture should be used. Cords rated for less amperage than the fixture may overheat.
- Always unplug the lighting fixture from the electrical outlet before cleaning and servicing or when not in use. Never yank the cord to remove the plug from the outlet.
- Let the lighting fixture cool completely before storing.
- To reduce the risk of electric shock, do not immerse this fixture in water or any other liquids. To reduce the risk of fire or electric shock, do not disassemble this fixture.
- Contact smallrig@smallrig.com or take it to qualified service personnel when service or repair work is required.
- Focalized optical conical snoot is not recommended to use with the light or it will burn the COB dlips.
- Power this fixture by connecting it to a grounded outlet.
- Please remove the protection cover before powering the light.
- Please remove the f’vA protection cover before using the reflector.
- Please do not block the ventilation and do not look at the light directly when it is powered on
- Please do not place the LED lighting fixture near any liquids or other flammable objects
- Only use a dry microfiber cloth to clean the product
- Please have the product checked by an authorized service personnel agent if your product has a problem.
- The malfunctions caused by unauthorized disassembly are not covered under the warranty.
- We recommend only using the original Small Rig cable accessories. Please note that our warranty for this product does not apply to any repairs required due to any malfunctions of unauthorized Small Rig accessories, although you may request such repairs for a fee
- This product is certified by CE, UKCA, RoHS, FCC, IC, TELEC, KC and RCM. Please operate the product in full compliance with the operation standards. Please note that this warranty does not apply to repairs arising from malfunctions, although you may request such repairs on a chargeable basis.
- The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design or specifications change.
FCC Compliance Statement
This device complies with Part l 5 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or mOOif1cations not expressly approved by the party res!XJnsible for compliance could void the user’s authority to operate the equipment
Note: This equipmet has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try reorienting or relocating the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet in a different circuit than the receiver
is connected to.
• Consult the dealer or an experienced radio/ TV technician for help.
RF Warning Statement
This device has been evaluated to meet general RF exposure requirements.
FCC ID: 2AZWl-3473LEQI
ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s).
Operation is subject to the following two conditions ·
- This device may not cause interference
- This device must accept any interference, including interference that may cause undesired operation of the device The digital apparatus complies with Canadian CAN ICES-3 (8)/NMB-3(8).
Checklist
When you unbox the product please make sure all the items below are included. Otherwise, contact with the seller immediately.
Product Details
Light
Installations
-
Attaching/ detaching the protection cover
Push the handle of the lever in the direction of the arrow shown in the picture, and rotate the cover to pull it out. Reverse rotation will put into the protection cover. -
Installation and removal of the reflector
Push the lever handle according to the arrow direction in the picture and rotate the reflector into it. Rotating in the opposite direction pulls out the reflector.
-
Setting up the light
Adjust the light to the appropriate height, rotate the tie-down to fix the light on the stand. Then, adjust the light to the required angel and tighten the lock handle. -
Soft light umbrella installation
Insert the soft light handle into the hole and lock the knob on the hole.
The Power Supply
Powered by AC
Notice: Please press the spring-loaded lock button on the power cord to remove the cord. Do not pull it out forcibly.
Powered by V-mount battery
Notice
- Please press the spring-loaded lock button on the power cord to remove it. Do not pull it out forcibly.
- Y-mount battery plate, battery, and power cable are not standard configurations and need to buy separately.
- The input voltage of the light is between DC 1 ‘2V and DC 30V
- The V-mount batteries that are 14.4V or 26V with the capacity above l S□Wh are recommended to use with the light.
- When using the l 4.4V V-mount battery or AC adapter under 2r:N, the maximum output will be reduced by 50%.
Operations
Press the power button to turn the light on and off.
Manual control
Brightness adjustment
Rotate the INT adjusting knob to adjust the brightness with 1% variable and
the brightness change range is 0-100%, the change of the brightness will be
displayed in real time on the light body.
Color temperature adjustment
Short press the I NT knob to adjust the color temperature, and the CCT range
is 270DK~6500K.
FX control
a. Rotate the FX knob on the right to get Normal and Paparazzi /TV/ Fault
Bulb/ Lightning/ Breath/ Party/ Flash/ Flame/ Firework, nine kinds of FX.
b. Shot Press the FX knob then switch to the frequency adjustment, the change
range is 1~10. Notice: The brightness of every FX can be set separately
Silent mode
Press the Reset button for three times, the silent mode is ON. Press for
another three times, then OFF. Notice: the cooling fan stops working when in
silent mode and the light also reduces the power.
BLE reset
- Long press the Reset button for 3 seconds, the BLE icon will appear in the upper right of the LCD display. The icon flashes 6 times and the BLE is reset.
- Then you can connect the light through SmallGoGo and control it again.
OTA mode
Firmware updates can be updated on line via the SmallGoGo App for OTA updates.
App control
The user can download the SmallGoGo App and connect the the device named 220B-
xxxxxx. After the light is controlled by the App, the BLE icon will be
displayed on the upper right of the light LCD.
Notice: Please enable the mobile location function when using the App.
Using the
SmallGoGo App
You can download the SmallGoGo App from the iOS App or Google Play Store
for enhancing the functionality of the light.
Please visit www.smallgogo.com for more details regarding how to use the app
to control you lights
Specifications
Light Operating Current
Light Power Supply
| 13A@2DV
DC12 – 30V
| Power Consumption
Cooling Mode
| 260W
Active Cooling
---|---|---|---
Adapter Power Supply
TLCI
| AC100 – 240V 50/60Hz
96•
| CRI
App Control Type
| 95+
BLE
Color Temperature| 2700K ~ 6500K(:t200K)| Remote Ability| 1oom
Radio Frequency
Size
| 2.4GHz
240 x 122 >< 237.6mm
| Power Supply
Weight
| AC/V-Mount batteries
2,850g :1: 20g
Photometrics
CCT
2700K
| Distance
Illumination
Bare Bulb
Hyper-Reflector
| lm
504(fc)
5420lux) 4591(fc)
49400(1ux)
| 3m
56(fc)
59B(lux) 36l(fc)
3880(1ux)
| Sm
22(fc) 239(1ux)
126(fc)
1360(1ux)
---|---|---|---|---
|
Bare Bulb
| 623(fc)
6700(1ux)
5929(fc)
638DD(lux) 806(fc)
867D(lux) 7853(fc)
845DD(lux) 699(fc)
752D(lux)
| 7l(fc)
762(1ux)
464(fc)
4990(1ux)
91(fc) 977(1ux)
613(fc)
6600(lux) 79(fc)
B45(1ux)
| 28(fc)
302(1ux)
163(fc)
l750(1ux) 36(fc)
386(1ux)
215(fc)
2310(1ux)
31(fc) 337(1ux)
3200K|
| Hyper-Reflector
|
Bare Bulb
5600K|
| Hyper-Reflector
| Bare Bulb
6500K|
Hyper-Reflector| 6831(fc)
73500(1ux)
| 537(fc)
578D(lux)
| 18B(fc)
2020(1ux)
This is an averaged result,the number might be slightly different on each light.
Guarantee Card
Serial No
Item Name
|
---|---
Purchase Date|
User Name|
Mobile|
Address
Receipt
|
Service Warranty
Please keep your original receipt and guarantee card. Be sure the dealer has
written on it the date of purchase and SN of the product. These are required
for warranty service.
After-sale warranty terms
- 7 Days DOA Return Policy: Within 7 days from the date of the package receipt, return or replacement can be done if the item received is malfunctioning or physical damaged (not caused by human abused), return shipping cost will be on Small Rig’s charge
- 1-Year Warranty: Within 1-year from the date of the package receipt, defective product which is not caused by human abuse is eligible to get repair/ replacement for free; defective product which is caused by human, repair/ replacement will be charged based on the damage level. In the event that the minimum warranty period stipulated by the laws of sales destination is longer than one year, such minimum warranty period shall prevail.
This warranty does not cover:
- Defect caused by users’ violation of the ”Warnings” and “Intended Use”,
- The product identification or SN label is removed or defaced in any way.
- The product is serviced or repaired by anyone other than our company or the service agency authorized by our company,
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>