MOUNTUP MU1005 Single Monitor Stand Instruction Manual
- June 14, 2024
- MOUNTUP
Table of Contents
- MU1005 Single Monitor Stand
- Safety Caution
- Installation Tools (Not Included)
- Supplied Parts and Hardware
- Product Dimensions
- STEP 1: Support Pillar Installation
- STEP 2: Apply Foot Pads to the Base
- STEP 3: Attach the Plate Component to Monitor
- STEP 4: Attach Monitor with Plate Component to Pillar
- STEP 5: Cable Management
- STEP 6: Adjustments (If necessary)
- Documents / Resources
INSTALLATION INSTRUCTION
MU1005 Single Monitor Stand
(ZDT10-C02-M_US2)
| 33 lbs
15 kg
---|---
| 75x75mm
100x100mm
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
BEFORE ASSEMBLY
- Layout all components and hardware. Check all parts are included and undamaged.
- Should anybody intends to install or use this monitor stand, please read and understand this manual carefully.
- If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.
WARNING
- This product contains small items that could be a choking hazard if swallowed.
- KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
- Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Installation Tools (Not Included)
Supplied Parts and Hardware
Hardware (Product)
Hardware (Monitor)
NOTE: Not all hardware included will be used.
Product Dimensions
STEP 1: Support Pillar Installation
Connect two Support Pillars (3 & 4 ) by using Connecting Plate 5 and Bolts (H). Use the 4mm allen key (H) to tighten the bolts.
Put Base 1 on the table; put Washers (B) and Bolts (A) on the base; keep clip holes of Support Pillar 4 toward backside then put Plastic Cover (D) and Support Pillar under 4 the base. Then tighten the bolts (A) with the 4mm allen key (G).
STEP 2: Apply Foot Pads to the Base
Hold the Support Pillar 4 with one hand and tear off plastic film of Foot Pads (F), then attach Foot Pads (F) near four conors of the Base 1 bottom.
STEP 3: Attach the Plate Component to Monitor
3-1 Select Monitor Screw Length
Thread screws by hand into the threaded holes on the back of your monitor and
then select which screw diameter fits your monitor. ** When attaching plate
to the flat screen, be careful not to over tighten screws and be sure that
screws do not bottom out in the mounting holes. 3-2 Attach the Plate
Componen t
(a) For Flat Back Monitor
NOTE:** If the MA screw is a little long, please use a H5mm spacer(M-H) to
fix it.
(b) For Recessed / Curved Back Monitor
STEP 4: Attach Monitor with Plate Component to Pillar
1.Choose the appropriate position for your monitors, hang the monitors onto the Support Pillar.
STEP 5: Cable Management
Attach Wire Clips (E) into the holes of Support Pillar. Manage cables with the Wire Clips (E).
STEP 6: Adjustments (If necessary)
Tilt Adjustment
- Slightly loosen tilting bolt with the Allen Key(G).
- Hold the monitor with both hands and adjust monitor to your desired tilt angle.
- Retighten tilting bolt to secure the monitor in place.
Note:
When tilted, if the monitor sags or does not stay, and if the above method is
useless, please feel free to contact our customer service.
Leveling Adjustment Swivel Adjustment
Documents / Resources
|
MOUNTUP MU1005 Single Monitor
Stand
[pdf] Instruction Manual
MU1005 Single Monitor Stand, MU1005, Single Monitor Stand, Monitor Stand,
Stand
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>