ROCAM CR1001eM Alarm Clock With Vibrator Instruction Manual

ROCAM CR1001eM Alarm Clock With Vibrator

LOCATION OF CONTROLS

1. Set Time & 12/24H Button
2. Hour Button
3. Minute Button
4. Dimmer & DST Button
5. OK & SNOOZE Button
6. Alarm Pause Button
7. Alarm OFF Button
8. Alarm 1 Button
9. Alarm 2 Button
10. PM Indicator
11. Alarm 1 Indicator
12. Alarm 2 Indicator
13. DST Indicator
14. Bell Indicator
15. Vibrator Indicator
16. Bell & Vibrator Toggle Button
17. Volume + Button
18. Volume – Button
19. Battery Compartment
20. USB Port
21. DC Jack
22. Vibrator Insert Port
23. Holder ( x 2pcs)
24. Speaker
25. Vibrator

Note: Batteries are not included

POWER RESOURCES

Insert the two included holders into the back of the clock to avoid it being knocked over.

1. Install 2pcs 1.5V “AAA” size batteries to the proper terminals in the battery compartment to memorize the time setting in case of power outage.
   NOTE: Batteries{not included) don’t support time display but can memorize time & alarm setting and trigger an alarm in case of AC power failure.

2. Connect the adapter line to DC jack , then plug into a 100-240V AC wall power outlet.

TIME SETTING

1. Press button once, display starts flashing.
2. Press button to set the hour. press button to set the minute.
3. Press button or button to save time or wait for 5 seconds to confirm automatically.
4. To change 12H/24H time format
   • Hold press button to switch 24H time format.
   • Hold press button again to switch 12H time format.

ALARM SETTING

Set the Alarm

1. Press button, the alarm indicator will light up, the display starts flickering.
2. Press button to set the hour, press button to set the minute.
3. Press button or button to save alarm time or just wait for another 5 seconds to confirm automatically.
4. Push or button to adjust alarm volume. Setting ALARM 2 is the same as ALARM 1.

Turn off Alarm

When alarm goes off:

1. Press button to temporarily turn off alarm for 9 minutes. Alarm will ring every next 9 minutes.
2. Press button to turn off today’s alarm. The alarm indicator or is still on, which means alarm is still activated and will ring after 24 hours.
3. Cancel Alarm
   • Press button to turn off alarm 2 permanently, corresponding indicator will turn off. Press button again to turn off alarm 1 permanently, corresponding indicator will turn off.
   • If alarm 1 goes off, then press button, just turn off alarm1 permanently. indicator will turn off.
   • If alarm 2 goes off, then press button, just turn off alarm 2 permanently. indicator will turn off.

DIMMER

Repeatedly press button to adjust the brightness of display for your preference.

There is 5 levels, The sequence is as follows:
3-4-5-4-3-2-1-2-3 ……..

DST

• Hold press button to switch to DST function.
• DST indicator will turn on.
• Hold press button again to turn off DST function.
• DST indicator will turn off.

USB CHARGING

• Plug charging cable into device such as phone or tablet.
• Device can charge your phone or tablet at the same time.
• The maximum charge current is 1 Ampere.

Vibrator

1. Insert the vibrator plug into the vibrator jack of the machine, the bell indicator and the vibrator indicator will light up, indicating that the bell and the vibrator will be effective at the same time.
2. Press button, the ring indicator goes off, and the vibrator indicator stays on, which means that when the alarm goes off, the vibrator will take effect, but the bell will not sound.
3. Press button again, the ring indicator goes on, and the vibrator indicator goes off, which means that when the alarm goes off, the bell will sound, but the vibrator will not shake.
4. Press button again, the ring indicator and the vibrator indicator goes on, which means that when the alam goes off, the bell and the vibrator will be effective at the same time.
   2-3-4 will continue to loop.

Speak with our Experts

• support@yelaw.net.
• http://www.yelaw.net.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>