ErGear EGESD19W Electric Standing Desk Instruction Manual

ErGear EGESD19W Electric Standing Desk

Product Information

Product Usage Instructions

1. Step 1: Supplied Parts and Hardware

Make sure you have the following parts:

• 01 x Desktop
• B1 x 1

Note: The B1 part is used for assembly.

Caution:
Ensure that all parts are included before proceeding to the next step.

Please refer to the detailed instruction manual for step-by-step assembly and usage guidelines.

Specifications

Height Adjustment Range
27.9”–46.4” (71–118cm)

Step 1
Supplied Parts and Hardware

Step 2
Supplied Parts and Hardware

Step 3
Supplied Parts and Hardware

Step 4
Supplied Parts and Hardware

Installation

Attaching the Legs to the Desktop

Attaching the Leg Bases

Attaching the Storage Hooks

Connecting the Cables

Using the Controller

Tip: Reset before first use.

Main Settings

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the highest position of 46.4” (118cm) or the button is released.

• Lower the Desk
  Press the button to lower the desk continuously until it reaches the lowest position of 27.9” (71cm) or the button is released.

• Save Current Height Setting
  Press the button and the screen will display ‘S-.’ Then press the 1, 2, 3, or 4 button to save the current height to that button. When you press 1, 2, 3, or 4 button, the desk will move to the height that was previously set for that button.

• Set Highest Height Limit

1. Press the button, and the screen will display ‘S-.’
2. Press and hold the button until ‘S-’ flashes once, and then release the button.
3. Quickly press and hold button again for 2 seconds, and ‘999’ will be displayed on the screen. Setting the highest limit is complete.

• Set Lowest Height Limit

1. Press the button, and the screen will display ‘S-.’
2. Press and hold the button until ‘S-’ flashes once, and then release the button.
3. Quickly press and hold button again for 2 seconds, and ‘00.0’ will be displayed on the screen. Setting the lowest limit is complete.

• Clear Highest/Lowest Height Limit

1. Press the button, and the screen will display ‘S-.’
2. Press and hold button again for 2 seconds, and ‘555’ will be displayed on the screen. Clearing the highest/lowest limit is complete.

• Lock/Unlock

1. To turn the lock on, press and hold the button, and the screen will display ‘S-,’ the current height, and then ‘LOC.’ The buttons will be disabled.
2. To turn the lock off, press and hold button for 8 seconds, and the screen will display current height. The buttons will be operable again.

• Reset

1. Press and hold the button until the desk goes down to its lowest level, and then release the button.
2. Press and hold button for 5 seconds until the screen displays ‘RST,’ and then release the button with ‘RST’ flashing.
3. Press and hold button again until the desk goes down to its lowest level and comes back up slightly. Reset is complete.

Other Settings

• To adjust the settings below, follow the reset instructions until the screen displays ‘RST.’ Next, follow the instructions for adjusting individual settings. Afterward, the screen will display ‘RST’ again. To exit, press and hold the button until the desk goes down to its lowest level and comes back up slightly or goes up to its highest level and comes back down slightly. The screen will display the current height.

Change Height Settings Operation
Press and hold the 1 button for 5 seconds to switch the mode.

1. One-Press Mode. Short-press the 1, 2, 3, or 4 button, and the desk will move to the height set for that button. Press any button to stop the desk.
2. Press & Hold Mode. Long-press the 1, 2, 3, or 4 button, and the desk will move toward the height set for that button while the button is held down.

Change Display Height Units
Press and hold the 2 button for 5 seconds to switch the display height units.

1. Metric (cm)
2. Imperial (inch)

Change Collision Detection Sensitivity
Press and hold the button for 5 seconds to switch sensitivity level.

1. High Sensitivity
2. Medium Sensitivity
3. Low Sensitivity

Change Displayed Minimum Height
If you attach a different desktop or add other things that change the desk surface level, you can adjust the displayed height to match. Press and hold the button for 5 seconds, and current minimum height will flash on the screen. Press the or button to adjust the minimum height, and then release the button to save. After 5 seconds, the screen will show ‘RST’ again. Saving is successful.

Protection Mode Error Codes

• E01/E02
  Overcurrent Protection: Input current too high. If the correct AC adapter is being used, reset the desk.

• E12
  Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, reset the desk.

• E07/E08
  Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, power back on again, and reset.

• H01
  Overheating Protection: When the motor has been working continuously for too long (total 2.5 minutes in 20 minutes), it will stop operating to prevent damage from overheating. Wait for the motor to cool down before making any further height adjustment.

Please try resetting the desk if you have any issues like the following:

• Abnormal operation.
• The controller screen displays an error message.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support

• (US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
• (UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)

Other Info
support@ergear.com.

Website
https://ergear.com.

References

• Complete Flexibility. Total Freedom – ErGear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>