ErGear EGESD6B-4 Electric Standing Desk with Keyboard Tray Instruction Manual

ErGear EGESD6B-4 Electric Standing Desk with Keyboard Tray

Product Information

The 55 Electric Standing Desk is a versatile and adjustable desk that allows users to easily switch between sitting and standing positions. It is equipped with a powerful motor that provides a smooth and quiet operating experience. The desk has a maximum weight capacity of 176 lbs (80 kg) and can be adjusted at a maximumspeed of 20mm/s. The power input ranges from 100V to 240V, making it suitable for use in various regions. The desk comes with all the necessary parts and hardware for assembly.

• Specifications
  • Power Input: 100V-240V
  • Max. Speed: 20mm/s
  • Operating Noise: 55dB
  • Max. Load: 176 lbs / 80 kg

Tools Needed

Tools Needed (Not lncluded)

Specifications

• Height Adjustment Range
  • 28.3”–46.5” (72-118cm)
• Power Input: 100V-240V
• Max. Speed: 20mm/s
• Operating Noise: ＜55dB
• Max. Load: 176 lbs / 80 kg

Supplied Parts and Hardware

Step 1

Step 2

Step 3

Step 4

Step 5

Installation Instructions

Step 1: Assembling and Connecting the Desk Legs

Warning: HEAVY! You may need assistance with this step.

Step 2: Attaching the Side Plates and the Transmission Rod

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

• Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.
• Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

Step 3: Assembling and Attaching the Desktop

• Assemble the desktop.
• Attach the desktop to the frame.
• Attach the controller and hooks to the desktop.

Step 4: Assembling and Attaching the Keyboard Tray

• Attach the stopper to the keyboard tray.
• You can use a drill (with suitable torque and speed) or a Phillips screwdriver.
• Attach the wrist rest to the keyboard tray.
• Pull out the inner parts of the drawer slides a little for easier keyboard tray alignment. Then align and insert the tray.
• Attach the assembled keyboard tray to the desk. You can use a Phillips screwdriver instead of a drill for easier access to screw in the screws.

Step 5: Connecting the Cables

Using the Controller

• Save Current Height Setting
  • Short-press the S button, and the display will flash. Press the 1,2 ,3 or button to save the current height setting to that button.
• Select Height Setting 1
  • Press the 1 button, and the desk will move to the height that was previously set for that button.
• Select Height Setting 2
  • Press the 2 button, and the desk will move to the height that was previously set for that button.
• Select Height Setting 3
  • Press the 3 button, and the desk will move to the height that was previously set for that button.
• Raise the Desk
  • Press the button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released.
• Lower the Desk
  • Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Settings And Error Codes

Settings

Change Display Height Units| Press and hold the S button until a flashing ‘S-’ is displayed. Press S again, and ‘Un’ is displayed. Press S to select it, press  or to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press S to save your choice.
---|---
Change Collision Force Detection| Long press the S button, ‘S-‘ shows and flashes. Press S again and the display shows ‘Un‘. Press  or to switch to ‘CF‘. Press S to select. Press  or  to switch between ‘OFF‘, Low (L), Normal (n) or Heavy (H) collision force detection.
Press S to save your choice.
Reset| Press and hold the  button for 5 seconds, and the screen will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
---|---
E10| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support

• (US/CA) 1-800-651-9525
  • Mon–Fri, 8am–8pm (CST)
• (UK) 44-808-196-3875
  • Mon–Fri, 2pm–10pm (UTC)
• Other Info: support@ergear.com
• Website: https://ergear.com

References

• Complete Flexibility. Total Freedom – ErGear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>