OKP K2P Robot Vacuum Cleaner Instruction Manual

K2P
Robot Vacuum Cleaner

Preparation

2.1 Assemble and charge

1. Remove the protective film on the robot and docking station
   

2. Install the side brushes
   

3. Placement of the charging base / connection of power supply

• Place the docking station on an open place.

• Connect the power supply and tidy up the power cord to avoid twining.
  

  4. Turn on the robot
     “ I ”means ON , “ O ”means OFF
     Reminder: Cannot charge when the robot is turned off.
     

  5. Charging
     Place the robot at Docking Station and make sure to align the charging electrodes.
     twinkling means charging.
     turn off means fully charged.
     A full charge takes 5 hours.
     

2.2 Using environment preparation

Tidy up the room

Organize the items on the floor, such as wires, slippers and other sundries to avoid affecting the operation of the robot

If the rug at home has fringed edges, please put the edges under the rug in advance.

Do not let the robot operate on wet floors.

The robot can climb to the top of objects with a height of less than 12mm. If you don’t want the robot to climb on them, please take them away.

Using the product

3.1 How to use buttons

Single press: Start/pause
Double press: Automatic return and charge
Keep pressing for 6 seconds:
Entering Wi-Fi pairing mode

Indicator Meaning

Battery is less than 50%: Pink light breath Clashing
Low battery-automatic
return and charge| Red light on
Cleaning complete-automatic return and charge| Pink light on
Entering Wi-Fi pairing mode| Blue light flash
Error| Red light on/flash

Using the product

3.2 App download and configuration

1. Downloading and installation of the “OKP” app Method I : Scan the following QR code, and then download and install App as prompted.
   https://mobile.okplife.com/#/pages/index/index
   Method II : Search “OKP” in the App store, download and install the OKP app.
   Note: The robot works with 2.4GHz Wi-Fi networks only.
   Tips:
   * Follow the guidance in the OKP app to register, login, and pair the robot.

• Please make sure that the mobile phone is connected to your Wi-Fi network before paring the robot vacuum cleaner. 2. Smart Life App Download and distribution network steps
  Smart Life enables interconnectivity between smart devices. This robot vacuum cleaner can also be managed and controlled directly through the Smart Life App.
  App download
  Method 1: Scan the following QR code and follow the prompts to download and install.
  https://smartapp.tuya.com/smartlife
  Method 2: Open the mobile app store, search for “Smart Life”, download and install it.
  Tips:
  After installation, please complete registration, login, and network distribution according to the instructions on the mobile app page.
  Before network distribution, please ensure that your mobile phone is connected to your home network.

Steps for network setup – Method 1 :
Step 1 : Please connect your mobile phone to a 2.4GHz Wi-Fi network. Note that this model only supports a 2.4GHz Wi-Fi network, so please ensure that your Wi-Fi network is a 2.4GHz network.
Step 2 : Enter distribution network mode.

1. Open the top surface of the robot and switch the toggle switch from “O” to “I”.
   The power light will turn on and a boot-up voice prompt will be heard.

2. Press and hold the“ ”key for 6 seconds, continue to hold it after hearing a “beep” sound, and release it when you hear two “beep-beep” sounds. The keys will then flicker slowly, indicating that the robot has entered distribution network mode.

If the distribution network fails, please restart the robot and try again.

Step 3 :

1. Open the Smart Life app and go to the homepage. Click on “Add Device” or the “+” icon in the upper right corner.

2. Wait for the app to scan for nearby devices and select the one you want to add.
   

3. Enter the Wi-Fi password and click “Next”.

4. Wait for the app to automatically connect the robot to the network(If it fails, you can try the following Method 2).
   

Steps for network setup – Method 2 :

Step 1 : Open the Smart Life App.

1. Select Add Device.

2. Select Small Home Appliances > Robot Vacuum (Wi-Fi).
   

3. Enter the Wi-Fi password and click “Next”.
   

Step 2 : First, put the robot in distribution network mode (refer to step 2 of Method 1), and then proceed with the following steps.

1. Click “Confirm the indicator is blinking”.
   

2. Select “AP Mode” .
   

3. Click on “Go to Connect”.
   

4. Find “SmartLife-xxx”and connect to it. Afterconnecting, return to the app and wait for the robot to connect successfully.
   

3.3 Maintenance-Dust bin1

• When cleaning and maintaining the robot and its accessories, please unplug the docking station.

Warning
The HEPA Filter should not touch the water.

1. Open the faceplate and take out the dust bin

2. Open the dust bin latch and dump the garbage

3. Remove the filter assembly
   

4. Clean the Pre-filter
   

5. Clean the HEPA-filter

3.3 Maintenance-Dust bin2

• When cleaning and maintaining the robot and its accessories, please unplug the docking station.

Warning
The HEPA Filter should not touch the water.

1. Open the faceplate and take out the dust bin

2. Open the dust bin latch and dump the garbage

3. Remove the filter assembly

4. Clean the Pre-filter

5. Clean the HEPA-filter

3.3 Maintenance-Others

• When cleaning and maintaining the robot and its accessories, please unplug the docking station.

1. Clean the anti-drop sensor to ensure the sensitivity of the sensor.

2. Clean the universal wheel to prevent hair from tangling.

3. Clean the suction mouth to avoid dust clogging.

4. Clean the driving wheel to ensure clean smoothly.

5. Clean the Anti-collision sensors to ensure sensitive obstacle avoidance.

6. Clean the charging electrode to ensure successful charging.

7. Clean the side brush to prevent hair from tangling.

8. Clean the charging electrode of the docking station to ensure successful charging.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>