OKP K7 Robotic Vacuum Cleaner User Manual

OKP K7 Robotic Vacuum Cleaner

Operating and Programming

Notes Before Cleaning

Please refer to the following guidelines to check the cleaning area before using the robot.

• Remove power cords and small objects from the Floor that could entangle the products.
  

• The product is not suitable for use on long- pile carpet. Before using the product near an area rug or on a short- pile area rug with tasseled edges, please fold area rug edges under themselves.
  

• Please be aware that the robot needs at least an 8 cm (3 ”) clearance to clean under furniture without complications.
  

• If there is a step or stairs in the cleaning area, please operate robot to ensure its Anti- Drop Sensor scan detect the drop off . It may be necessary to place a physical barrier at the edge of the drop off to keep the unit from falling over the edge.
  

Quick Start

Charging Dock Placement

1. Connect the adapter to the charging Dock
   Place the Charging Dock on a level floor surface against the wall with the base perpendicular to the ground. Keep the immediate area 2m (6.6’) in front of the charger and 1 m(3.3’) on both sides of the charger clear of objects and reflective surfaces. Plug the Charging Dock in. The Power Indicator Light on the Charging Dock glows.
   Place the charging Dock
   
   Connect the power supply
   

2. Install Side Brushes
   Attach Side Brushes to the bottom of robot by pressing a brush into each slot until it clicks.
   

3. Remove Protector Before using the Robot, please remove the front bumper and charging station Protective strip and protective film.
   

Start to Charge

1. Turn on the Robot
   Turn the robot’s Side Power Switch to the ON position. “-” indicates ON and “ O” indicates OFF. Robot is powered ON when button glows a continuous BLUE.
   

2. Charge Robot
   Place robot on the Charging Dock making sure the Charging Contacts on robot and the Charging Dock Pins make a connection. Charge Robot for at least 4 hours before the first use.
   

• Usually take 5.5 hours from low battery mode to fully charged.
• button in breathing status when robot is charging. button stops glowing after robot is fully charged.

Start Cleaning

Press the button on Robot or on the Remote Control. robot starts to work immediately in AUTO Cleaning Mode.

The robot will enters sleep mode after standby for 10 minutes, and the Start/Pause button light goes off . If you need to select another mode, please refer to the section (mode selection).

Pause

Pause robot by pressing the button on robot or the button on the Remote Control.

• when the Robot is Pause, the robot can be moved forward or left or right by remote control as needed.

Cleaning Mode Selection

The Robot has several cleaning modes to choose from to effectively clean different floors. Cleaning modes are selected using the Remote Control.

Spot Cleaning Mode

(Less than 3 minutes)

This mode is applicable for an area of highly concentrated dirt or duct. In Sport Cleaning Mode, Robot focuses on a specific area to clean. Robot cleans the area in a spiral pattern using MAX suction power and stops when it completes Spot Cleaning.

To start Spot Cleaning Mode, press Spot Cleaning Mode on the Remote Control.

Edge Cleaning Mode

This mode is good for cleaning the edges and corners of a room. In Edge Cleaning Mode, Robot cleans along a border using MAX suction power (e.g. wall). To start Edge Cleaning Mode, press the Edge Cleaning Mode Button on the Remote Control.

Programmed Cleaning Mode

Robot will clean in Programmed Cleaning Pattern optimized for hard floors.

Return to Charger Mode

When battery power gets low, Robot automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself. Alternatively double click on the Start/Pause button on the robot to start the Return to Charger Mode.

*Robot can also be sent back to the Charging Dock at any time by pressing the Return to Charger Button on the Remote Control.

APP download and network configuration

Scan the QR code to download and install the app
This app is compatible with IOS9.0 and Android 4.0 or above. ios system: Please search“ OKP life” in the app store. Android system: Please scan the QR code or search “ OKP Life” on google play to download.

Connect to your Indoor 2.4G WIFI network
Make sure the mobile device is connected to the indoor 2 . 4 G WIFI network, and the signal quality is good enough, register and log in to the mobile app.

EZ MODE

Network paring (Only works with 2.4G WIFI)

• Turn on the POWER switch on the side to turn on the ROBOT.
  

• Press and hold the  ▢ START/ PAUSE button simultaneously for about 3 seconds until you hear a beep. The WiFi indicator flashes quickly and the ROBOT enters into EZ network configuration mode.
  

If you experience with network pairing failure, please restart the robot and start over again. Or try the AP mode network pairing method instead.

AP MODE

Network paring AP mode (Only works with 2.4G WIFI)

• Turn on the POWER switch on the side to turn on the ROBOT.
  

• Press and hold the START/PAUSE button simultaneously; after you hear a beep in about 3 seconds, continue holding  the button for another 3 seconds until you hear two beeps. The WiFi indicator flashes slowly and the ROBOT enters  into AP network configuration mode.
  

Add Manually- Wi-Fi-AP Mode

Connect your phone to a Wi-Fi that starts with then name“ SmartLife”.

After successfully connecting to the Wi-Fi, return the APP and start the network configuration.

Maintenance

Dust Bin and Filters

When cleaning and maintaining the robot and its accessories, turn off the robot  and unplug the Charging dock.

1. Remove the dustbin, open the dustbin cover, and empty the Dust Bin.
   

2. Remove dust filter. HEPA is not recommended for washing. Pat the High Efficiency Filter clean.
   

3. Flush the Dustbin and the filter net.

4. Dry the Sponge filter, Dust Bin and Filter Net completely before reinstalling.

Roller Brush and Side Brushes

Cleaning Roller Brush

• Turn the robot over. Push both buttons on the Roller Brush Cover and remove it. Remove the Roller Brush. Use the Multi Function Cleaning Tool to cut off and remove any hair tangled around the Roller Brush.
  

Cleaning the Side Brushes

• Remove the Side Brushes. Wipe the Side Brushes and their slots with a dry cloth.

Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Universal Wheel.

Clean the driving wheel to maintain it’s effectiveness.

Other Components

• Clean the anti-collision sensor panel.

• Wipe the Anti-Drop Sensors with the brush or the felt side of the Multi-Function Cleaning Tool to maintain their effectiveness.

• Wipe the Charging Contacts and Charging Dock Pins with the brush of the Multi-Function Cleaning Tool or a dry clean cloth to maintain their effectiveness.
  

If you do not use this product for a long time, please take out the battery and keep it properly. If the battery leaks, remove the battery, And wipe the battery cell clean. This product has a Long life battery and does not need to be replaced frequently. If you need to replace it, you can contact our after- sales service for replacement.

Indicator Light

Lighting Effects

networking status
Low Battery| Red light is always on| As per current networking status
Cleaning Mode| Blue light is always on| As per current networking status
Before starting distribution network| Blue light is always on| Blue light flashes
Distribution process/ Loss of signal reconnection| Blue light is always on| Exit the distribution network after 5 minutes, the blue light is off
Connect to Wi- Fi| Blue light is always on| Blue light is always on

Common alarm tips

Glows a continuous Red

No.| Cause of Issue| Beep| Solutions
1| Drive wheel| 1 beep
3  times| The drive wheel is abnormal. Please check if the drive wheel is entangled and clean it.
2| Side Brushes| 2  beep
3   times| If the side brushes are abnormal, please check if the side brush is entangled and clean the side brushes.
3| Fan abnormal| 3 beep
3  times| The fan is abnormal, please clean the dustbin and air duct outlet.
4| Roller brush| 4  beep
3  times| The roller brush is abnormal. Please check if the roller brush is entangled and clean the roller brush.

Flashes Red

No.| Cause of Issue| Beep| Solutions
1| Front infrared Anti- collision bumper| 1 beep
3  times| The bumper is abnormal. Please check if the infrared buffer bumper is stuck.
2| Anti- Drop sensor| 2  beep
3   times| The ROBOT is suspended, please move to the ground
3| Out of Trouble| 3 beep
3  times| the ROBOT fail to get out of trouble, please move to the open space
4| Low battery| 4  beep
3  times| the battery is too low, please charge
5| Adapter Exception| 5 beep
3  times| the charging voltage is abnormal, please replace the adapter.
6| Abnormal charging status| 6 beep
3  times| Charging is abnormal, please check if the switch is turned on.

Tips

if the above method does not solve the problem, please try the following: re- open the power switch on the side of the robot to restart the machine.

Troubleshooting

Please use this chart to troubleshoot common problems using robot.

sure the WIFI name and the password are entered correctly.
Make sure the robot is less than 5 feet(0.5 meter)away from the router and your phone – the closer the better!| Ensure the robot is under WIFI signal coverage.
Robot isn’ t in network pairing mode.| Make sure the robot is in the network pairing mode.
Didn’ t connect to 2. 4 G Wi- Fi signal.| The robot doesn’t connect compatible with 5G WiFi signal, Please connect to 2.4G WiFi signal.
Download the incorrect APP| Please scan the QR code in the user manual or search “ OKP life” on google play or app store.
| The  robot is too noisy.| Side brush, rolling brush,entangled, dustbin Filter material blocked, etc.| It is recommended to clean and maintain the brush, roller brush,dustbin and filters regularly.
The robot is in MAX suction power mode.| Change the suction power mode to Medium or Low.
NO| Malfunction| Possible Causes| Solutions
---|---|---|---
| Robot will not Charge.| Robot has not made a connection with the Charging Dock.| Be sure that robot’ s Charging Contacts have made a connection with the Charging Dock Pins.
Charging Dock is unplugged while robot is powered ON, which causes battery. consumption.| Plug in the Charging Dock and ensure robot is powered ON. Keep robot on the Charging Dock to make sure it has a full battery to work at any time.
| Robot gets into trouble while working and stops.| The robot is entangled or obstructed by scattered wires on the ground, drape curtains or carpet edges.| Robot will try various ways to get itself out of trouble.
If it is unsuccessful, manually remove the obstacles and restart.
Side Brush is stuck or the rotation speed of the Side Brush decreases.| Remove the debris tangled around the Side Brush. If the Side Brush still rotates slowly, contact Customer Service.
Roller Brush is stuck or the rotation speed of the Roller brush decreases.| Remove the debris tangled around the roller Brush with the provided Multi- Function Cleaning Tool. If the Roller Brush still rotates slowly, contact Customer Service.
| Robot returns to the Charging Dock before it finishes cleaning.| When battery power gets low, robot automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself.| This is normal. No solution necessary.
Working time varies according to floor surface,room complexity and the selected Cleaning Mode.| This is normal. No solution necessary.
| Robot will not clean automatically at scheduled time.| Time Scheduling function is cancelled.| Turn on the power switch of the robot, reconnect the network and use the APP to check the scheduled settings.
Robot is powered OFF( once the robot is power off, the time scheduling settings via remote control will be removed).| Power on the robot and make the schedule using the remote control over again.
The robot’ s battery is low.| Keep robot powered ON and on the Charging Dock to make sure it has a full battery to work at any time.
The robot’ s components are tangled with debris.| Power OFF robot, clean the Dust Bin, and invert the robot. Clean Side Brushes and the Roller Brush as described in section 4.
| Remote Control failure( effective control range of Remote Control is 5m (16’).| The batteries in the Remote Control need to be replaced.| Replace the battery with a new one and install it properly.
Robot is powered OFF or robot’s battery is low.| Make sure robot is powered ON and fully charged.
The infrared signal cannot be transmitted because the Infrared Emitter on the Remote Control or robot’ s Infrared Receiver on robot is dirty.| Use a dry cloth or the Multi-Function Cleaning Tool to wipe the Infrared Emitter on Remote Control and the Infrared Receiver on robot.
There is other equipment interfering with the infrared signal to robot.| Avoid using the Remote Control near other equipment using infrared signals.

If the trouble cannot be eliminated according to the above operation, Please contact support@okplife.com
The images are only for reference, please refer to the actual item as the standard. OKP reserves the right to update products without prior notice.

Customer Support

Okp Technologies Corp
http://www.okplife.com / support@okplife.com Part of the eastern section, level 4 Building 3, Longcheng Industrial Park, Huanggekeng Community, Longcheng Street, Longgang District, Shenzhen

References

• OKP Robot Vacuum – Leading the Future of Home Cleaning – okplife

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>