AURORA AU-A1ZBSCCX Aone Tuneable LED Strip Controller Instruction Manual

June 4, 2024
Aurora

AURORA logo AU-A1ZBSCCX Aone Tuneable LED Strip Controller
Instruction Manual

AU-A1ZBSCCX Aone Tuneable LED Strip Controller

MODEL AU-Al ZBSCCX
INPUT VOLTAGE (V) 12-24V DC
INPUT CURRENT 8A @ 24V DC / 12V DC
OUTPUT VOLTAGE 12-24V DC
NUMBER OF OUTPUTS 1 (includes warm white and cool white)
MAX LOAD 96W @ 24V DC per output

48W @ 12V DC per output
AMBIENT TEMPERATURE LIMITS| -20°C—+50°C
IP RATING| IP20 (Indoor Use Only)
NUMBER OF OPERATING CYCLES| 1 E4
CIRCUIT DISCONNECTION| Electronic disconnection
PROTOCOL| ZigBee 3.0
CONDUCTOR TYPE & SIZE| Twin and Earth 0.75-1.5 mm2 (UK) Flat x2C+E 0.75-2.5 mm2 (Australia)
FREQUENCY BAND| 2.405 – 2.483GHz
MAX OUTPUT RF POWER| 12.66dBm
INSULATING MATERIALS| Polycarbonate
GLOW-WIRE TEMPERATURE| 850°C
PROTECTIVE DEVICE| 100°C Recoverable temp control

  • There are no restrictions on use.
  • Installation must be carried out in accordance with the latest edition of the Wiring Rules by a qualified electrician.
  • Earth terminal is for Termination only.
  • Hereby, Aurora Limited declares that the radio equipment type AU-A1ZBSCCX is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.auroralighting.com/ProductDetail/AU-A1ZBSCCX

USING THE APP TO CONNECT THE LED STRIP CONTROLLER TO THE HUB

  1. Download the AOne App from the App Store.
  2. Follow instructions on the App to send the hub into pairing mode and pair your devices (further details below).
  3. Put the controller into pairing mode by:
    a) Connecting the controller to a power outlet and turning on the power, or,
    b) Pressing the pairing button for 3 seconds, or,
    c) Powering the controller off for a minimum of 2 seconds and back on again 6 times. The on periods must be between 0.5 – 1.5 seconds.
    The LED Strip will flash twice to indicate it has entered pairing mode.
    The LED Strip will flash a third time to indicate that it has successfully paired with the hub.
    The controller can then be controlled using the AOne App.

IMPORTANT INFORMATION:

  • The strip controller works on 12V/24V DC, it cannot be used with 220-240V AC directly.
  • Remove any existing dimmers from the circuit.
  • The strip controller fits between the non-dimmable LED driver and LED strip (LED driver NOT included).
  • We recommend that LED strips below 10W per meter can run a maximum of 10m and for LED strips above 10W per meter a maximum of 5m. This is based on an incoming cable between the driver and the start of the LED strip of 5m.
  • For further details please check specific LED strip data.

AURORA AU A1ZBSCCX Aone Tuneable LED Strip Controller - Figure
1| AURORA AU A1ZBSCCX Aone
Tuneable LED Strip Controller - Figure 2| AURORA AU A1ZBSCCX Aone Tuneable LED Strip Controller -
Figure 3
---|---|---
AURORA AU A1ZBSCCX Aone Tuneable LED Strip Controller - Figure
4
AURORA AU A1ZBSCCX Aone Tuneable LED Strip Controller - Figure
5| AURORA AU A1ZBSCCX Aone
Tuneable LED Strip Controller - Figure 6| AURORA AU A1ZBSCCX Aone Tuneable LED Strip Controller -
Figure 7

Environmental Protection (W.E.E.E.) – Aurora’s WEEE Reg.No. WEE/BG0130YX (UK Only)
Waste Electrical & Electronic Equipment Regulations (WEEE) require that any of our products showing this marking (left) must not be disposed of with other household or commercial waste. Aurora does not levy any WEEE disposal charges to its customers for affected WEEE-related products. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate any such product from other waste types and recycle it responsibly at your local facilities. Check with your Local Authority, Recycling Centre, or retailer for recycling advice. If, when you purchased any Aurora product, your supplier included a WEEE disposal fee, you should then contact your supplier for advice on his takeback of the product for the correct disposal.
Warranty
See www.auroralighting.com/warranty for full details of warranties and Extended Warranty Terms and Conditions. The warranty is invalid in the case of improper use, tampering, and removal of the Q.C. date label, installation in an improper working environment, or installation not according to the current edition of the National Wiring Regulations. Should this product fail during the warranty period it will be replaced free of charge, this is subject to correct installation and return of the faulty product. Aurora does not accept responsibility for any installation costs associated with the replacement of this product. This warranty is in addition to the statutory rights in your country of purchase. Aurora reserves the right to alter specifications without prior notice.
AURORA logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Aurora User Manuals

Related Manuals