PoEWit NS-8B 12-Port L3 Managed Switch User Guide
- June 4, 2024
- Poewit
Table of Contents
PoEWit NS-8B 12-Port L3 Managed Switch
About Guide
This guide provides instructions to install the NS-8B switch
NOTE : The model you have purchased may appear slightly different from the illustrations shown in the document. Refer to the Product Instruction and Technical Specification sections for detailed information about your switch, its components, network connections, and technical specifications.
This guide is divided into four parts:
- About guide: Terminology/Usage
- Product introduction: Product overview and panel definitions
- Hardware installation: Step by step hardware installation process
- Technical specifications
Terminology / Usage
In this guide, the term “Switch” (first letter capitalized) refers to this PoE
Switch, and “switch” (first letter lower case) refers to other PoE switches.
Some technologies refer to terms “switch”, “bridge” and “switching hubs”
interchangeably, and both are commonly accepted for Ethernet switches.
Note : Indicates important information that helps a better use of the
device.
Warning : Indicates potential property damage or personal injury.
Copyright and trademark
The pictures and data shown in this guide are for reference only, subject to
change without notice.
Product Introduction
This Switch is a 10G Full Managed PoE Switch. It provides 8 x10/100/1000Mbps Auto-Negotiation RJ45 PoE ports and 4 x10Gbps SFP ports, which can satisfy the full speed forwarding of ports. The Switch uses 19” 1U standard chassis rack or can be used on the desktop.
Front Panel
The front panel consists of LED indicators and network ports.
LED Lamp
Power LED : The Power LED lights up when the Switch is connected to a
power source.
Link/Act indicator : The light indicates the network connection through
the corresponding port. Flicker indicates that the switch is sending or
receiving data.
PoE indicator: Blinking indicates that the PD device is connected to the
corresponding port, and Off indicates that the port is not powered or no PD
device is found.
Rear Panel
The rear panel view of the Switch consists of an AC power connector.
Plug the female connector into the Switch and male connector into a power outlet. Supports input voltages 100-240VAC, 50/60Hz.
Switch: Turn on the switch after inserting the power cord, “I” means to
turn on, “O” means off.
Grounding: Use specialized ground lead connect.
HARDWARE INSTALLATION
This chapter provides unpacking and installation information for the Switch.
Open a Seal
Open the shipping carton and carefully unpack its contents. Please consult the
packing list located in the User Manual to make sure all items are present and
undamaged. If any item is missing or damaged, please contact us for
replacement.
- Switch 1 pcs
- AC power cord 1 pcs
- Rubber feet 4 pcs
- Screws 6 pcs
- Mounting brackets 2 pcs
- User’s manual 1 pcs
- Serial port lines 1 pcs
Switch Installation
For safe switch installation and operation, it is recommended that you:
- Visually inspect the power cord to see that it is secured fully to the AC power connector.
- Make sure that there is proper heat dissipation and adequate ventilation around the switch.
- Do not place heavy objects on the switch.
Desktop Installation
When installing the switch on a desktop, the rubber feet included with the
device must be attached on the bottom at each corner of the device’s base.
Allow enough ventilation space between the device and the objects around it
.
Rack Installation
The switch can be mounted on a EIA standard size 19-inch rack, which can be
placed in a wiring closet with other equipment. To install, attach the
mounting brackets to the switch’s side panels (one on each side) and secure
them with the screws provided.
Then, use the screws provided with the equipment rack to mount the switch in
the rack.
Plugging in the AC Power Cord
You can connect AC power supply cord to switch back and the other side to a
power outlet (power outlet must be well grounded and support over voltage
protection).
Warning : Do not turn on the power switch before power cables are
connected. Power surge may cause damage to the Switch.
Using Web-based Management
After a successful physical installation, you can configure the Switch,
monitor the network status, and display statistics using a web browser.
Supported Web Browsers
The embedded Web-based Management currently supports the following web
browsers:
- Internet Explorer 6 or higher version
- Chrome
- Mozilla
- Firefox 1.5/2.0 or higher version
You will need the following equipment to begin the web configuration of your device:
- PC with a RJ-45 Ethernet connection
- Standard Ethernet network cable
With a standard Ethernet cable, connect the Ethernet cable to any of the ports
on the front panel of the switch and to the Ethernet port on the PC.
Login Web-based Management
- To access the GUI of the switch, open a browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key.
Note:
- To log in to the switch, the IP address of your PC should be set in the same subnet as that of the switch. The IP address is 192.168.0.x (”x” is any number from 2 to 254). Subnet Mask is 255.255.255.0.
- Enter admin for both the User Name and Password in lower case letters. Then click the Login button or press the Enter key.
- After a successful login, the main page will appear as follows, and you can click the menu on the left side to configure the corresponding functions.
Note: For more details about how to configure the switch, see the User Guide on www.poewit.com.
TECHNICAL SPECIFICATIONS
| Project | Description |
|---|---|
| Fixed port | 8×10/100/1000Mbps PoE ports and 4x10Gbps SFP port |
| Standards and protocols | IEEE802.3 10Base-T Ethernet standard IEEE802.3u |
100Base-TX Fast Ethernet standard IEEE802.3ab 1000Base-T Ethernet standard IEEE802.3z Gigabit Ethernet (fiber)
IEEE802.3x Full duplex flow control and Backpressure Half duplex flow control IEEE802.3ab Link aggregation
Rate| 10/100/1000Mbps
LED Indicators| Power, Link/Act, PoE
AC Input Voltage Range| 100V~240V AC, 50/60Hz
Power consumption| 20W
Operating temperature| 0°C 40°C
Storage temperature| -10°C 70°C
Relative humidity| 20%~85% (non-condensing)
Switching Fabric| 96G
MAC Addresses| 16K
PoE Technology|
PoE Compliance| 100% IEEE 802.3af, 802.3at compliant, 802.3bt compliant
PoE Classification| PSE (Power Sourcing Equipment)
PoE Voltage| +52 VDC
PoE Power Budget| 500W
PoE Operation| Automatic detection and power management
PoE Port| 8 ports support Ultra PoE (90W max)
PoE Pin Assignments| V+ (Pin 3, 6,4,5), V- (Pin 1, 2,7,8)
PoE Disconnect Mode| DC disconnect
Software Technology
Port Feature| Port Control, Port Isolation, Port Self-loop Detection
Port Mirroring| Multi to 1 Sniffer
VLAN| Port-base & 802.1q Tag-base VLANs
Link Aggregation| Up to 8 maximum aggregation groups, each containing up to
4GE
Traffic control| IEEE 802.3x full-duplex flow control
Rate Limit| Unit: 64kbps
Spanning Tree| Support STP, RSTP, MSTP
Ring Protocol| Support EAPS
Multicast| Support 256 Multicast groups, Support IGMP Snooping
QoS
| 4 output queues on each port
Support flexible queue scheduling algorithms: WRR, Q+WRR
Support port-based / MAC-based / 802.1p / DSCP classification
ACL| Support Standard IP / Extend IP / MAC IP / ARP, up to 512 entries
Security
| Support MAC-based 802.1X authentication
Support AAA/RADIUS authentication
Support WEB/Telnet password protection
Support Accessing privilege mode password protection
SMNP| Support
Configuration File| Support Download/Upload configuration File via WEB
Upgrade Firmware| Support Upgrade Firmware via WEB
Management Interface| Support WEB, SNMP, CLI, Telnet, Console
Mechanical
Casing| Metal
Dimensions (W x L x H)| 440 mm x 200 mm x 44 mm
Installation| Rack mounting or Desktop
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>