ErGear EGESD6B Height Adjustable Electric Standing Desk Instruction Manual

55″ Electric Standing Desk

Instruction Manual

Rev02(A)

EGESD6B / EGESD6V / EGESD6N

Technical Support:
(US/CA) 1-800-651-9525 Mon-­Fri, 8am­-8pm (CST)
(UK) 44-808-196-3875 Mon­-Fri, 2pm-­10pm (UTC)
Other Info: support@ergear.com
Website: https://ergear.com

Tools Needed (Not Included)

      OR
Drill                            Phillips Screwdriver

Specifications

Height Adjustment Range 28.3″­ – 46.5″ (72-118cm)

Power Input 100V-240V       Max. Speed 20mm/s

Operating Noise <55dB          Max. Load 176 lbs / 80 kg

Step 1

Supplied Parts and Hardware

01 x 1                                        02 x 1

Crossbar                                  Left Desk Leg

03 x 1                                    04 x 2 A x4

Right Desk Leg                        Leg Base                     Bolt M6 x 11mm

B x8                                    C x1

Bolt M6 x 35mm               Large Allen Wrench 3/16″ (5mm)

Step 2

Supplied Parts and Hardware

05 x 2                            06 x 1

Side Plate                       Transmission Rod

A x4                                                C x1

Bolt M6 x 11mm       Large Allen Wrench 3/16″ (5mm)

D x1                                                  E x 10

Small Allen Wrench 5/64″ (2mm)    Rubber Pad

Step 3

Supplied Parts and Hardware

07 x 1                                08 x 1 F x 16

Desktop                         Controller            Screw M5 x 16mm

G x6                              H x2

Wood Dowel Pin       Storage Hook

Step 4

Supplied Parts and Hardware

09 x 1                                    I x2

AC Adapter                      Cable Clip

Step 5

Supplied Parts and Hardware

J x2

Cable Hole Cover

Step 1 Assembling and Connecting the Desk Legs

1. Large Allen Wrench

HEAVY! You may need assistance with this step.

1. Large Allen Wrench

Step 2 Attaching the Side Plates and the Transmission Rod

1. Large Allen Wrench

Loosen the coupling nut.

1. Coupling nut

1. Turn anti-clockwise

1. Turn clockwise

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

1. NOTE: Make sure the set screw faces out.

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.

1. Small Allen Wrench

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

Tighten the coupling nut to fine- tune transmission rod fit.

Step 3 Assembling and Attaching the Desktop

Assemble the desktop.

Attach the desktop to the frame.

                      OR
(not Drill included)           Phillips Screwdriver (not included)
You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

Attach the controller and hooks to the desktop.

Step 4 Connecting the Cables

Step 5 Installing the Cable Hole Covers

Using the Controller

• Save Current Height Setting
  Short-press the [S] button, and the display will flash. Press the [1] , [2] , or [3] button to save the current height setting to that button.

• Select Height Setting 1
  Press the [1] button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the [2] button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the [3] button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the [∧] button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.

• Lower the Desk
  Press the [∨] button to lower the desk continuously until it reaches the lowest position of 28.3″ (72cm) or the button is released.

Settings

Change Display Height Units

| Press and hold the [S] button until a flashing ‘S-’ is displayed. Press [S] again, and ‘Un’ is displayed. Press [S] to select it, press [ ∧ ] or [ ∨ ] to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press [S] to save your choice.
---|---

Change Collision Detection Sensitivity

| Long press the [S] button, ‘S-‘ shows and flashes. Press [S] again and the display shows ‘Un.‘ Press [ ∧ ] or [ ∨ ] to switch to ‘CF.‘ Press [S] to select. Press [ ∧ ] or [ ∨ ] to switch between ‘OFF,‘ Low (L), Normal (n) or Heavy (H) collision force detection. Press [S] to save your choice.

Reset

| Press and hold the [ ∨ ] button for 5 seconds, and the screen will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot

| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
---|---

E10

| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.

E20

| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.

E02

| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.

E32

| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.

E31

| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.

E60

| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.

–

| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Complete Flexibility. Total Freedom.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support
(US/CA) 1-800-651-9525    Mon­-Fri, 8am­-8pm (CST)
(UK) 44-808-196-3875         Mon­-Fri, 2pm­-10pm (UTC)

Other Info
support@ergear.com

Website
https://ergear.com

860-00288-02 Rev02

References

• Complete Flexibility. Total Freedom – ErGear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>