ErGear EGESD12V Electric Standing Desk Instruction Manual

EGESD12V Electric Standing Desk

Product Information

The Electric Standing Desk is a versatile desk that can be
adjusted to different heights to accommodate various users. It is
designed for indoor use only and comes with a range of features to
enhance usability.

Key Specifications:

• Power Input: 100V-240V
• Max. Speed: 20mm/s
• Operating Noise: 55dB
• Max. Load: 176 lbs / 80kg

Product Usage Instructions

Step 1: Assembling and Connecting the Desk Legs

You will need the following parts and hardware:

• 01 x Crossbar
• 04 x Left Desk Leg (A)
• 02 x Right Desk Leg (B)
• 03 x Leg Base (C)
• Bolt M6 x 11mm
• Bolt M6 x 35mm

Using a large Allen wrench, assemble and connect the desk legs
as per the instructions provided in the manual.

Step 2: Attaching the Side Plates and the Transmission Rod

You will need the following parts and hardware:

• 05 x Side Plate
• 06 x Transmission Rod
• Bolt M6 x 11mm
• Coupling nut

Use a large Allen wrench to attach the side plates and the
transmission rod to the desk legs. Follow the instructions provided
in the manual for proper installation.

Step 3: Assembling and Attaching the Desktop

You will need the following parts and hardware:

• 07 x Desktop
• 08 x Rubber Pad
• 09 x Controller
• G x4 Cable Management Tray
• H x2 Storage Hook
• F x 20 Wood Dowel Pin
• J x4 Desktop Panel Connector

Assemble the desktop and attach it to the frame using a drill or
a Phillips screwdriver. Also, attach the controller, storage hooks,
and cable management tray to the desktop as per the instructions
provided.

Step 4: Attaching the Felt Board and Felt Storage Bag to the

Desktop

You will need the following parts and hardware:

• 10 x Felt Board
• 11 x Felt Storage Bag
• A x2 Screw M5 x 16mm
• C x1 Screw M5 x 12mm
• Bolt M6 x 11mm

Attach the felt board and felt storage bag to the left or right
side of the desktop using a hammer and a large Allen wrench. Follow
the instructions provided in the manual for proper attachment.

Step 5: Connecting the Cables

You will need the following parts and hardware:

• L x2 Drawing Pin
• Cable Clip (not included)

Connect the cables according to the instructions provided in the
manual. Use the drawing pins and cable clips to secure the cables
in place.

Step 6: Using the Felt Board

Now that the desk is assembled and all the components are in
place, you can start using the felt board. Use it to pin important
notes, reminders, or any other items you need to keep within easy
reach while working.

Electric Standing Desk
Instruction Manual
EGESD12B / EGESD12V Rev00(A)

Technical Support: (US/CA) 1-800-651-9525 (UK) 44-808-196-3875

Mon­Fri, 8am­8pm (CST) Mon­Fri, 2pm­10pm (UTC)

Website: https://ergear.com

Other Info: support@ergear.com

IMPORTANT SAFETY INFORMATION
· This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. · Children shall not play with the appliance. · Cleaning and user maintenance shall not be made by children without supervision. · The appliance is only to be used with the power supply unit provided with the appliance. · Disconnect the supply when carrying out maintenance and cleaning. · Examine the appliance frequently for signs of wear or damage. If there are such signs or if the appliance has been misused or does not work, contact the supplier for further information. · Do not allow children to play with fixed controls. · When operating a switch that initiates and maintains the movement of the furniture or terminates the movement of the furniture or causes a change of the direction of the movement of the furniture, make sure that other persons are kept away. · Properly place the appliance to avoid creating entrapment hazards with other furniture. · Dust off regularly to keep your desktop clean. Power off the desk, and then use a damp piece of cloth to gently rub.
For indoor use only
03

Tools Needed (Not lncluded)

Drill
Specifications

OR Phillips Screwdriver

Hammer

Height Adjustment Range 28.3″­46.5″ (72-118cm)

Power Input 100V-240V

Max. Speed 20mm/s

Operating Noise 55dB

RATED
Max. Load 176 lbs / 80kg

Step 1
Supplied Parts and Hardware

01 x 1
Crossbar
04 x 2

02 x 1

03 x 1

Left Desk Leg
A x4

Right Desk Leg
B x8

Leg Base
C x1

Bolt M6 x 11mm

Bolt M6 x 35mm

Step 2
Supplied Parts and Hardware

Large Allen Wrench 3/16″ (5mm)
05 x 2
Side Plate

06 x 1
Transmission Rod

A x4
Bolt M6 x 11mm
04

C x1

D x1

E x 10

Step 3
Supplied Parts and Hardware

Large Allen Wrench 3/16″ (5mm)
07 x 1
Desktop
I x2

Small Allen Wrench 5/64″ (2mm)
08 x 1

Rubber Pad
09 x 1

Controller
G x4

Cable Management Tray
H x2

Storage Hook
F x 20

Wood Dowel Pin

Desktop Panel Connector

J x4

Step 4
Supplied Parts and Hardware

Screw M5 x 16mm
10 x 1
Felt Board
K x4

Plastic Buckle

Screw M5 x 12mm
11 x 1

A x2

Felt Storage Bag
C x1

Bolt M6 x 11mm

Large Allen Wrench 3/16″ (5mm) 05

Step 5
Supplied Parts and Hardware
Step 6
Supplied Parts and Hardware

12 x 1
AC Adapter
M x6
Drawing Pin

“DUVBMQBSU NBZWBSZGSPN JNBHFTIPXO

L x2
Cable Clip

06

Step 1

Assembling and Connecting the Desk Legs

03

Large C Allen Wrench
02 01 A 03
01

HEAVY! You may need assistance with this step.
04 04
04

Large C Allen Wrench B

07

Step 2

Attaching the Side Plates and the Transmission Rod

05

05 A C Large Allen Wrench
05

Coupling nut 06

Loosen the coupling nut.
08

Fig 1

a

Turn

b

anti-clockwise

06

Left Leg

Fig 2

Before attaching the transmission rod,

measure the heights of the two desk legs to see

a

if they are set at the same level. If not, insert the

Turn clockwise transmission rod into the hole in the left leg.
b
Turn the rod to adjust the left leg so it’s level

Left Leg

with the right leg. Turn the rod clockwise to

lower the left leg or anti-clockwise to raise it.

NOTE: Make sure the set screw faces out.

Right Leg

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.
09

D Small Allen Wrench
Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.
E
Tighten the coupling nut to fine-tune transmission rod fit.
10

Step 3 Assembling and Attaching the Desktop
Assemble the desktop.
07
G 07

Attach the desktop to the frame.

07

(not

Drill included)

OR

Phillips Screwdriver (not included)

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

OR F
F H
11

Attach the controller, storage hooks and cable management tray to the desktop.

a

OR

F I

OR
c
J
09

a c
b

OR
b
F 08
12

Step 4

Attaching the Felt Board and Felt Storage Bag to the Desktop

Attach the felt board and felt storage bag on the left or right as you need.

Left

OR

Right

Hammer (not included)

K 10

Large Allen Wrench A
C 11

Left

OR

Right

Large

A

Allen Wrench C

11

13

Step 5 Connecting the Cables
12

L

08

08

12

Not lncluded

14

Step 6 Using the Felt Board
M 10
Not lncluded
15

Using the Controller
Save Current Height Setting
Short-press the button, and the display will flash. Press the , , or button to save the current height setting to that button.
Select Height Setting 1
Press the button, and the desk will move to the height that was previously set for that button.
Select Height Setting 2
Press the button, and the desk will move to the height that was previously set for that button.
Select Height Setting 3
Press the button, and the desk will move to the height that was previously set for that button.
Raise the Desk
Press the button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.
Lower the Desk
Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.
16

Change Display Height Units

Settings
Press and hold the button until a flashing S-‘ is displayed. Press again, and Un’ is displayed. Press to select it, press or to switch between IN’ (imperial) andSI’ (metric), and press to save your choice.

Change Collision Detection Sensitivity

Long press the button, S- shows and flashes. Press again and the display shows Un. Press or to switch to CF. Press to select. Press or to switch between OFF, Low (L), Normal (n) or Heavy (H) collision force detection. Press to save your choice.

Reset

Press and hold the button for 5 seconds, and the screen will show `RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Overheating Protection: When the motor has been working

Hot

continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes

before making any further height adjustment.

Sensor Malfunction Warning: Motor safety sensor can’t be

E10

detected. Power off, check the connection between the

motor and controller, and power back on again.

Overloading Warning: Max load exceeded. If raising the

desk, take the things off the desk and try again. If lowering

E20

the desk, power off, take the things off the desk, power

back on, and try again.

If error code persists, follow the reset instructions.

Operation Status Warning: The desk stops moving if

E02

vibration, impact, or incline are detected. If this detection

is incorrect, follow the reset instructions before continuing

use.

17

Overvoltage Protection: Input voltage too high. If the correct

E32

AC adapter is being used, power off the desk, check the

connection between power and the controller, and power

on again.

Undervoltage Protection: Input voltage too low. If the correct

E31

AC adapter is being used, power off the desk, check the

connection between power and the controller, and power

on again.

Unequal Leg Height Warning: Power off the desk and

E60

check whether the left and right legs are at the same

height. Adjust if necessary by following the instructions.

Power on again.

Cable Disconnection Warning: Check motor and controller

­

cable connections. Normal operation should return once

all connectors are properly connected.

18

Complete Flexibility. Total Freedom

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support: (US/CA) 1-800-651-9525 (UK) 44-808-196-3875

Mon­Fri, 8am­8pm (CST) Mon­Fri, 2pm­10pm (UTC)

Other Info: support@ergear.com

Website: https://ergear.com

860-00966-00 Rev00

References

• Complete Flexibility. Total Freedom – ErGear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>