VEVOR HCP750A-D Sand Filter Pump for Above Ground User Manual

VEVOR HCP750A-D Sand Filter Pump for Above Ground

Product Information

• Product Name: Swimming Pool Pump
• Model: HCP750A-D
• Manufacturer: VEVOR
• Support and E-Warranty Certificate: https://www.vevor.com/support

Product Usage Instructions

1. Before operating the swimming pool pump, carefully read and understand all the instructions provided in the user manual.
2. Ensure that you have received the correct model, as the appearance of the product may vary.
3. Contact Customer Service at CustomerService@vevor.com if you have any product questions or need technical support.
4. Important Warning and Safety:
   • This sand filter must be installed and used correctly to prevent serious bodily injury or death.
   • Installers, pool operators, and pool owners must read all warnings and instructions before using this sand filter.
   • Comply with state and local codes that regulate the construction, installation, and operation of pools and spas.
   • Do not allow children to use or operate the sand filter.
   • Electrical equipment must be grounded before connecting to the power supply to avoid electrical shock hazards.
   • Turn off power to all electrical equipment before working onelectrical connections.
   • This sand filter is intended for use with storable pools only. Do not use it with permanently installed pools.
   • Release all pressure from the sand filter and read instructions before working on it to avoid injury or property damage.
5. Air Release: Press down the control valve handle to release air before starting the pump after winterizing, maintenance, and backwashing. Repeat this operation every time.
6. Ensure components such as the filtration system, pumps, and heater are positioned to prevent access to the pool by young children.

Support and E-Warranty Certificate https://www.vevor.com/support
SWIMMING POOL PUMP
USR MANUAL
MODEL:HCP750A-D
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

MODEL:HCP750A-D

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

CustomerService@vevor.com

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

IMPORTANT WARNING AND SAFETY3

DANGER

• SERIOUS BODILY INJURY OR DEATH CAN RESULT IF THIS SAND FILTER IS NOT INSTALLED AND USED CORRECTLY.
• INSTALLERS,POOL OPERATORS,AND POOL OWNERS MUST READ THESE WARNINGS AND ALL INSTRUCTIONS BEFORE USING THIS SAND FILTER.

WARNING

• This sand filter is intended for use in swimming pool applications.

• Most states and local codes regulate the construction, installation, and operation of public pools and spas and the construction of residential pools and spas.It is important to comply with these codes,many of which directly regulate the installation and use of this product. Consult your local building and health codes for more information.

• Do not permit children to use or operate this sand filter.
  Before installing this product,read and follow all warning notices and instructions in this Guide. Failure to follow warnings and instructions can result in severe injury,death, or property damage.

• BEFORE WORKING ON THE FILTER!
  Air Release:
  Press down the control valve handle to release the air.

NOTE: It is important to repeat this operation every time you start the pump after winterizing, maintenance, and backwashing.

CAUTION
Components such as the filtration system, pumps, and heater must be positioned so as to prevent being used as means of access to the pool by young children.

WARNING

• Electrical ground all electrical equipment before connecting to the electrical power supply.Failure to ground all electrical equipment can cause a serious or fatal electrical shock hazard.
• To avoid dangerous or fatal electrical shock, turn OFF power to all electrical equipment before working on electrical connections.

CAUTION
This sand filter is for use with storable pools only.Do not use it with permanently installed pools. The storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.

DANGER
High Pressure from the Sand Filter can cause severe injury or major property damage due to tank separation.
Release all pressure and read instructions before working on the sand filter.

If the filter clamp is adjusted under pressure,the tank can separate,causing serious injury or major property damage.

DANGER
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION: PUMPS REQUIRE HIGH VOLTAGE, WHICH CAN SHOCK, BURN, OR CAUSE DEATH.

BEFORE WORKING ON THE PUMP!
Always disconnect power to the pool pump at the circuit breaker from the pump before servicing the pump.Failure to do so could result in death or serious injury to the service person,pool users, or others due to electric shock.

WARNING
A pool or spa pump must be installed by a qualified pool and spa service professional in accordance with the National Electrical Code and all applicable local codes and ordinances Improper installation may create an electrical hazard which could result in death or serious injury to pool users, installers,or others due to electrical shock and may also cause damage to property.

ASSEMBLY DIAGRAM

FILTER OVERVIEW

Your high-rate sand filter is designed to produce clear,sparkling water and operate for years with a minimum of maintenance when installed,operated and maintained in accordance with these instructions.

Your filter uses special filter sand to remove dirt particles from pool water.
Filter sand is loaded into the filter tank and functions as the dirt-removing media.The pool water,which contains suspended dirt particles,is pumpedthrough your piping system and is automatically directed by the filtercontrol valve to the top of the filter tank.As the pool water is pumped through the filter sand,dirt particles are trapped by the sand bed and filtered out.The cleaned pool water flows from the bottom of the filter tank,up through the standpipe,and back to the valve on top of the filter where the clean water is returned to the pool through the piping or hoses.

After a period of time,the accumulated dirt in the filter causes a resistance to flow,and the flow diminishes.This means it is time to clean(backwash) your filter.With the control valve in the backwash position,the water flow is automatically reversed through the filter So that it is directed to the bottom of the tank,up through the sand flushing the previously trapped dirt and debris out of the waste line.Once the filter is back washed(cleaned)of dirt,the control valve is manually resequenced to Rinse and then Filter to resume normal filtering.

SPECIFICATIONS

PUMP

| Model| HCP750A-D
---|---|---
Nominal voltage| AC110-120V,60Hz

750W

Amp| 6.5A
Max.head| 43ft
Max.flow| 3500GPH
Protection class| IPX5
Insulation class| F

Top Mount Filter

| Filter Diameter| 16”
---|---|---
Effective filtration area| 0.12 ㎡
Tank volume| 38L
Required media type| #20 silica sand
Required media amount| 30kg
Max.Working pressure| 35psi

INSTALLING THE FILTER

Read and understand all instructions before attempting to install,operate or maintain your pump and sand filter system.

1. Carefully remove all individual components from the carton and inspect for any visible damage.If the carton or parts are damaged,contact the seller or freight company.
   WARNING
   Blockage of suction fittings can cause serious or fatal injury due to drowning.To reduce the risk of injury,do not permit children to use
   Never work on the pump while it is running or power is still connected.High voltage can cause serious or fatal injury.A suitable ground fault interrupter(GFCI)should always be installed at the power supply source of this unit.Be sure to ground the motor before connecting it to the electrical AC power supply.Failure to ground the motor can cause a serious or fatal electrical shock hazard.DO NOT ground to a gas supply pipeline.

2. The filter system should be installed not more than 50cm above pool water level,on a level concrete slab,very firm ground,or equivalent,as recommended by your pool dealer.When the filter is filled with sand and water,it can weigh several hundred pounds.Position the filter so that the piping connections,control valve and winter drain is accessible for operation,service,and winterizing.

3. Assemble the drain to the lower outlet at the bottom of the filter tank.Make sure that the o-rings are correctly assembled to prevent water leakage.See the figure below.

4. Place the filter tank on the system base and rotate clockwise a little bit. Position the filter tank,so the winter drain faces the opposite direction of the pump.

5. Assemble the pump to the system base.

6. Place the standpipe and underdrain assembly in the center of the tank. Cap the standpipe with a sand shield to prevent sand from entering it.Fill the tank with about half-full water.Be sure the winter drain cap is securely in place).Carefully pour in the correct amount and grade of filter sand(Be sure the standpipe remains centered in the opening).
   IMPORTANT
   You must use only No.20 standard silica sand having a uniformity coefficient of 1.75 or less. No.20 silica sand has a particle size of.018-.022 inches(.45 to.55 mm).
   Note:Sand is not included.

7. Remove the sand shield from the standpipe.Wash away all sand around the opening at the top of the tank.Be sure the top of the filter is free of any sand or debris and valve o-ring is in place on the valve body. Insert Filter
   Control Valve into the tank neck, taking care that the standpipe slips into the hole in the bottom of the valve.

8. Position the valve so that the port locations are in the desired final position.Valve ports are marked with the location of where they should be connected,i.e.,the pump port must go to pump discharge,the waste port must go to the waste line,and the return port must go to the pool return.

9. Wipe the filter flange clean.Place the flange clamp around the tank and valve flange and assemble the screws and nuts with the hex key.Tighten clamp screws firmly and visually check the valve tank and clamp assembly to ensure that the joint is correctly assembled.
   WARNING
   High Pressure:
   Improper tank valve assembly could cause the valve to separate and cause serious injury and/or major property damage.

10. Wrap some Teflon pipe manufactured for the plastic pipe on the 14″NPT male end of the gauge.Carefully screw the pressure gauge into the 1/4″NPT tapped hole in the valve body.Do not over-tighten.

11. Screw the hose adaptors into the control valve port marked PUMP and pump discharge port.Wrap five turns of Teflon pipe on each hose adaptor.Connect the hose adaptors with a 1.5”hose and use a hose clamp to fix them

12. Make a return to the pool pipe connection to the control valve opening marked RETURN and complete other necessary plumbing connections,waste lines,suction lines to pump,etc.

13. To prevent water leakage,be sure the winter drain cap is securely in place and all pipe connections are tight.

CAUTION
KEEP SAFETY LABELS IN GOOD CONDITION AND REPLACE IF MISSING OR DAMAGED.

FILTER CONTROL VALVE FUNCTIONS

• FILTER: From the pump,through the valve,downward through the filter sand bed,up through the center pipe to the valve return port,and back to the pool for normal filter action and vacuuming the pool through the filter.
• BACKWASH: From the pump,through the valve,down through the center pipe,up through filter sand to the valve,and out waste port.This position is used for cleaning the filter by reversing flow.
• RINSE: From the pump,through the valve,downward through filter sand,up through the center pipe to the valve,and out waste port.This position is used for start-up cleaning and resettling the filter bed after backwashing.
• WASTE: From the pump,through the valve,bypasses the filter and goes to the waste port.This position is for vacuuming directly to waste,lowering the pool level,or draining the pool.
• CLOSE: NO FLOWIN THIS POSITION-DO NOT USE THIS SETTING WHILE THE PUMP IS OPERATING.
• WINTER: Valve position for a winterized filter.

INITIAL START-UP

1. On a new pool,clean the pool before filling the pool with water.
   Excessive dirt and large particles can cause damage to the pump and filter.

2. Ensure that all pool suction and WASTE lines are open so that water is free to flow from the pool to the WASTE line.Set the control valve to the BACKWASH position.

3. Check the valve clamp for tightness.

4. Check the pump strainer pot to be sure it is full of water(Ensure the hose is full of water if there is no strainer basket).Tighten the pump lid.
   Prime and start the pump,allowing the filter tank to fill with water.
   CAUTION
   DO NOT DRY RUN THE SAND FILTER.

5. Once the water flow is steady out the WASTE line,run the pump for at least 2 minutes or until the backwash water is clean.This initial backwashing of the filter is recommended to remove any impurities of fine sand particles in the silica sand media.

6. Turn the pump off and set the valve to the“RINSE”position.Ensure that all pool suction and WASTE lines are open so that the water is free to flow from the pool to the WASTE line.STAND CLEAR OF FILTER and start the pump.

7. Run the pump for at least two minutes.

8. Turn the pump off and set the valve to the“FILTER”position.Be sure that all pool suction and RETURN lines are open so that water is free to flow from and back to the pool.STAND CLEAR OF FILTER and start the pump.

9. The filter has now started its filtering cycle.You should ensure that water is returning to the pool and take note of the operating pressure when the filter is clean.

10. Check the system for water leaks.If a leak is found,shut the pump off before correcting the leak.

11. As the filter removes dirt and impurities from the pool water,the accumulation will cause the filter pressure to rise and flow to diminish.When the pressure gauge reading is 5-10 psi higher than the clean filter reading noted above,it is time to backwash the filter.

CLEANING

1. The filter on a new pool should be back-washed,and cleaned after approximately 48 hours of operation to clean out plaster dust and/or construction debris.

2. There are three different ways to identify when the filter needs backwashing.

3. The most accurate indicator on pool systems with a flow meter is to backwash when the flow decreases 30%from the original(clean filter)flow.For example,if the original flow was 60 GPM,the filter should be back-washed when the flow is reduced by about 20 GPM(or 30%)to 40 GPM.
   A more subjective and less accurate indicator is to observe the amount of water flowing from the flow directionals located in the wall of the pool.The filter should be back-washed once it is detected that the flow has been reduced.
   The most commonly used but less accurate indicator is to backwash when the filter gauge reading increases by 10 PSI over the initial(clean filter)reading.

4. It is important not to backwash the filter solely on a timed basis,such as every three days.It is also important to note that backwashing too frequently actually causes poor filtration.Factors like weather conditions, heavy rains,dust or pollen,and water temperatures all affect the frequency of backwash.As you use your pool,you will become aware of these influences.

5. To prevent damage to the pump and filter and for proper operation of the system,clean the pump strainer and skimmer baskets regularly.

6. If,at any time,the starting pressure after backwashing the filter indicates 4 to 6 PSI higher than the normal starting pressure,it is time to perform a chemical cleaning procedure.

FILTER BACKWASH PROCEDURE

1. Stop the pump.
   WARNING
   Always turn the pump off before changing valve positions.
   Changing valve positions while the pump is running can damage the control valve,which may cause serious injury or property damage.

2. Ensure that the suction and WASTE lines are open so that water is free to come from the pool and flow out the WASTE line.Set the control valve to the“BACKWASH”position.

3. STAND CLEAR OF FILTER and start the pump.

4. Backwash filter for approximately 3 to 5 minutes or until backwash water is clean

5. Stop the pump and set the valve to the“RINSE”position.

6. STAND CLEAR OF FILTER and start the pump.

7. Rinse the filter for approximately 30 seconds.

8. Stop the pump and set the valve to the“FILTER”position.

9. Ensure the pool RETURN line is open so that water may flow freely from the filter back to the pool.

10. STAND CLEAR OF FILTER and start the pump.

11. The filter has now started its filtering cycle.Verify the water is returning to the pool,and take note of the filter pressure when the filter is clean.

12. The filter pressure in Step 11 above should not exceed the pressure originally observed on the filter when it was initially started.If,after backwashing,the pressure is 4 to 6 psi above the start condition,it will be necessary to chemically clean the sand bed.

WINTERIZING YOUR FILTER

WARNING
Allowing water to freeze in the system will damage the system and cause potential water damage/flooding and potential property damage

In areas that have freezing winter temperatures,pool equipment must be winterized to protect against damage.

1. Backwash the sand filter.

2. After back washing,shut the pump off and move the handle of the valve to the WINTER position.
   CAUTION
   The multiport valve should be left in the“WINTER”position during the shutdown season.Failure to do so can damage the system,which can cause property damage from leaking water.
   

3. Remove the drain cap on the bottom of the filter tank and leave the cap off during winter. Completely drain the filter tank.

4. Drain and winterize the pump.

5. Drain all appropriate system piping.

WINTERIZING YOUR FILTER TROUBLESHOOTING

Pool water is not sufficiently clean.| 1. Pool chemistry is not adequate to inhibit algae growth.

2. Improper amount or wrong sand size.

3. Inadequate turnover rate.

| 1. Maintain pool chemistry or consult a service technician.

2. Check sand bed depth and sand size or consult a pool service technician. 3.Run the system for a longer time or consult a dealer or pool service

technician.

---|---|---
Control Valve leakage| 1. Control Valve is set between two functions.

2. The gasket is broken.

| 1. Set the valve to the correct function.

2. Replace the gasket.

The motor is Running,but no water flows through the pump.| 1.Air is entering the system. 2.Suction height too high,incorrect position.| 1. Check all hose/pipe connections and ensure the strainer lid is tightened.

2. Position the

system/pump to a lower place.

Sand is flowing into the pool.| 1.Sand is too small. 2.The level of the sand is too high.

3.Broken underdrain

assembly.

| 1.Use#2O silica sand 2.Lower the sand level to 2/3 of the filter

3.Replace broken or

damaged assembly.

---|---|---
Higher filter pressure.| 1.Insufficient Backwashing. 2.Partially closed valve or restriction.| 1. Backwash until effluent runs clear.

2. Open the valve or remove

the obstruction in the

return line.

Return flow to pool diminished,low filter pressure,| 1.Obstruction in the pump. 2.Obstruction in the suction line to pump.| 1. Disassemble and clean the pump.

Clean strainer/skimmer basket.

2. Remove obstruction in

lines.

Manufacturer: Ningbo HongTong Motor Co.,Ltd
Address： No.28 Rongda Road, Lizhou Street, Yuyao, Zhejiang 315400CHINA
Made In China

Support and E-Warranty Certificate https://www.vevor.com/support

References

• Hjem - LESS
• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>