Waterdrop WD-TSA-10 Triple Stage Undersink Water Filtration System Instructions

Waterdrop WD-TSA-10 Triple Stage Undersink Water Filtration System

WARNING I Please read it carefully before installation.

Specifications

• Operating temperature: 2-38°C/3s-100° F
• Working pressure: 10-125psi (0.7-8.6bar)
• Flow rate: 1gpm
• Filter capacity:
  • WD-1 OPP: up to 6 months
  • WD-1 OGC: up to 8-12 months
  • WD-1 OCT: up to 12-18 months
• Feed water requirement: Municipal tap water

Note: The service life mentioned above is subject to chlorine reduction. Actual result varies according to the local water quality.

Precautions

• Do not use it with water that’s microbiologically unsafe or of unknown quality without adequate disinfection.
• For use only with cold water.
• Do not freeze the filter, as this can cause cracking and water leakage.
• Do not allow children under 3 years old to have access to small parts during installation of this product.
• This installation must comply with all applicable state and local regulations.
• Turn off the water supply while replacing the filter.

Installation of the filter system

Tips: How to disconnect the quick-connect?
Use your thumb and index finger to press down on the lock sleeve. Use your other hand to pull out the hose from the fitting.

Note: Please do not pull out the tubing directly, or else it will damage the fitting and cause leakage.

Step 1: Fix the filter head and the filter

1. Paste the assistant label to finish drilling.
   Note: Mount the water filter at least 2 inches higher than the ground for easier filter change.

2. Install the screw and reserve enough space to hang the filter.

3. Hang the filter system on the screw.

Step 2: Connect the water supply (cold water only)

1. Shut off the water supply. Remove the faucet hose. (Figure 1)
2. Connect the inlet hose to the cold water valve.
   • If the angle valve outlet is 3/8′; it can be directly connected to the water supply. (Figure 3)
   • If the angle valve outlet is 1 /2′; connect it with a No.1 converter at first. (Figure 4)

Step 3: Conned to the faucet

1. If the angle valve outlet is 3/8′; it can be directly connected to the water supply. (Figure 5)
2. lf the angle valve outlet is 1/2′; connect it with a No.2 converter at first. (Figure 6)

Note: If a female threaded connector is needed, please contact our service team for help.

Step 4: Connect to the filter system
Connect the inlet hose and the outlet hose to the filter head. Make sure the hoses hit the bottom of the filter head.
Note: When the hose is tightly inserted, there will be a 1/8 inch gap between the hose and the filter head, which is designed for easy replacement and won’t affect the sealing performance.

Step S: Flush the filter and check the leaks

1. Flush the filter for 5 minutes before use.
2. If water leakage occurs, turn off the water supply. If the water leakage is occurring at position 1 and 2,wrap Teflon tape on the external thread. If the water leakage is occurring at position 3 or 4, insert the quick-connect fitting to the end and make sure the hoses hit the bottom of the fitting.

Filter replacement

1. It’s recommended to turn off the water supply and turn on the faucet to release the water pressure.
2. Rotate 1/4turn to the left to remove the filter.
3. Take out the new filter and remove the protective cap. 4. Rotate 1/4 turn to the right to install the filter. Ensure that the filter’s triangle mark is aligned with the connection mark.
4. Turn on the cold water valve and flush for 5 minutes.

Frequently asked questions

• Q:What should I do if water leaks after installation?
  A: In the event of water leakage, turn off the water supply. If the water leakage is occurring at the thread, wrap Teflon tape on the external thread. If the water leakage is occurring at the quick connection position, insert the quick-connect fitting to the end and make sure the hoses hit the bottom of the fitting. Contact us for solutions if the water leakage persists.

• Q: Why doesn’t the TDS value lower after filtration?
  A: The main purpose of this waterdrop filter is not to remove TDS. TDS stands for total dissolved solids, and it is basically composed of inorganic salts and a small amount of organic matter. The filter can remove harmful substances while keeping beneficial trace elements. Please choose Waterdrop RO system if you are looking for physical removal ofTDS.

• Q: When should I replace the filter?
  A:The filter’s service life is related to the water quality. If the flow rate is significantly reduced or if the water has a peculiar smell, we suggest that you replace the filter. The recommended service life of the filter is as follows: The PP filter has a 6 month lifetime; the GC filter has an 8-12 months lifetime; the CT filter has an 12-18 months lifetime.

• Q: What substances can the filter reduce?
  A: Our premium coconut carbon block filter has been tested by an independent laboratory against NSF standards. It can effectively reduce chlorine, taste and odor, cysts, hydrogen sulfide, and other heavy metals.

• Q: What is the difference between the WD-TSA system and the WD-TSB system?
  A: The WD-TSA system does not come with a faucet. It will connect to your existing faucet. Meanwhile, the WD-TSB system comes with an additional water faucet.

1 -year quality assurance
All mechanical devices with moving parts have a normal life span and will need to be replaced periodically. For this reason, mechanical devices such as water fittings, filter head, and faucets have a limited replacement assurance of 1 year. No assurance is given as to the service life of any filter cartridge, as the service life will vary based on local water conditions and water consumption.
If the product proves to be defective within 1 year from the date of purchase, please contact our customer service department. During the assurance period, we will replace or repair any part that is deemed to be defective if the product has not been subjected to tampering, alteration, or improper use after delivery, and has not been repaired by the manufacturer.
We do not make any promises in the event of misuse, use in abnormal temperature conditions, conditions outside those listed in the operating parameters, or use in commercial operations.

Manufacturer Technical Support
Tel: 1-888-352-3558 (U.S.)

E-mail: service@waterdropfilter.com

Made in China V04
Qingdao Ecopure Filter Co., Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>