VEVOR SV-500VA Voltage Converter Transformer Instruction Manual
- June 14, 2024
- VEVOR
Table of Contents
VEVOR SV-500VA Voltage Converter Transformer
Important Information
We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands
MODEL:SV-500VA/SV-1000VA/SV-2000VA/SV-3000VA/SV-5000VA
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
[email protected]
This is the original instruction, please read all manual instruction scare fully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
ATTENTION
The voltage input range of this product can be selected by toggles witch, please check that the voltage of the mains and the switching voltage of the product should be consistent before powering on.
RODUCT PARAMETERS
Model| SV-500VA| SV-1000VA| SV-2000VA| SV-3000VA|
SV-5000VA
---|---|---|---|---|---
Input
voltage
| AC110V±15% or AC 230V±15%
Output
voltage
| AC110V±15% and AC 230V±15%
Output
power
| 500VA| 1000VA| 2000VA| 3000VA| 5000VA
Overload
protector
| 5A| 10A| 18A| 28A| 45A
Operating
temperature
| -30℃~55℃
relative humidity| 5%~95%
Instructions for use of the product
Set the input toggle switch of the product to a position consistent with the mains voltage.(As shown in the figure below).
- Set the input toggle switch of the product to a position consistent with the mains voltage.(As shown in the figure below).
The input voltage is 220V-240V rule Switch to position 220.
The input voltage is 100V-120V rule Switch to position 1102.
-
Insert the input power cord into the end of the product, and then insert the plug of the power cord into the mains outlet.
✮Note :Before plugging in the mains, please check whether the position of the input voltage transfer switch is consistent with the mains voltage. -
Please use the load according to the voltage of the panel output socket, the load power must be less than the nominal power of the device, and there commended load power is 80% of the rated power.
✮Because the equipment itself has a certain loss, the load use power must be less than the nominal power of the equipment, other wise there is a risk of damage to the equipment. 4.The panel USB output port outputs 5V/1.5A DC as an emergency to charge other smart devices.
Notes:
- This equipment is equipped with an overcurrent fuse (SV-500VAorSV2000VA), which will blow when the load exceeds the load of thee equipment. When you find that there is no output, check the replacement fuse.
- This equipment has an overload protection switch, when the load exceeds the load of the equipment, the overload protection switch will automatically spring up and disconnect the output; When the load overload is solved, you can press the overload protection by hand to open it and resume work.
- This equipment is equipped with an air switch, when the load is overloaded for a long time, or the load is short-circuited, the air switch will immediately turn off the output, thereby protecting the equipment from damage. When the load fault is lifted, close the air again and open it, and it can work normally.
Device panel
Warning
This equipment is a high voltage device, please do not attempt to disassemble this equipment at any time to avoid danger. After a device failure, if the external switch fails to restart the device, please contact your reseller for handling.
Technical Support
Technical Support and E-Warranty
Certificatewww.vevor.com/support