JVC GY-HD100 Series HD Camera Recorder Instructions
- June 14, 2024
- JVC
Table of Contents
JVC GY-HD100 Series HD Camera Recorder
Product Information: GY-HD100/GY-HD101 HD Camera Recorder
The GY-HD100/GY-HD101 HD Camera Recorder is a professional-grade camera designed for high-definition video recording. It comes with a lens, viewfinder, microphone, and battery pack for a complete shooting setup.
Key Features:
- High-definition video recording
- Professional-grade performance
- Included lens, viewfinder, microphone, and battery pack
Product Usage Instructions
Before operating the GY-HD100/GY-HD101 HD Camera Recorder, please read the following instructions carefully:
Preparations
Ensure that you have completed the necessary preparations before using the
camera recorder:
- Attach the lens, viewfinder, microphone, and battery pack to the camera recorder.
- Refer to the manual for detailed instructions on attaching these components.
Setting and Adjustments Before Shooting
Prior to shooting, it is important to configure the settings and make
necessary adjustments:
- Refer to the manual for instructions on setting up the camera recorder for optimal performance.
**Shooting Operation
**
To start recording high-definition videos, follow these steps:
- Power on the camera recorder.
- Frame your shot using the viewfinder or LCD screen.
- Press the record button to begin recording.
- Make any necessary adjustments to exposure, focus, and other settings as needed.
- Press the record button again to stop recording.
Playback Mode
To review and play back recorded videos:
- Enter playback mode using the designated button or menu option.
- Navigate through the recorded videos using the playback controls.
- Adjust volume and other playback settings as desired.
**Using External Components
**
The GY-HD100/GY-HD101 HD Camera Recorder supports external components for enhanced functionality:
- Refer to the manual for instructions on connecting and utilizing external components such as monitors, audio devices, and more.
Menu Screens
The camera recorder features various menu screens for accessing and
adjusting settings:
- Explore the menu screens to customize the camera recorder’s behavior according to your preferences.
- Refer to the manual for detailed information on each menu option.
We hope you enjoy using the GY-HD100/GY-HD101 HD Camera Recorder. For further assistance, refer to the user manual or contact our customer support.
GY-HD100/GY-HD101 HD CAMERA RECORDER
Downloaded from: https://www.usersmanualguide.com/
E
HD CAMERA RECORDER
GY-HD100 INSTRUCTIONS GY-HD101
INTRODUCTION
CONTROLS, INDICATORS AND CONNECTORS
PREPARATIONS
PREPARATIONS FOR OPERATION
SETTING AND ADJUSTMENTS BEFORE SHOOTING
SHOOTING OPERATION
PLAYBACK MODE
USING EXTERNAL COMPONENTS
MENU SCREENS
FEATURES OF THE CAMERA SECTION
OTHERS
is a registered trademark owned by Victor Company of Japan, Limited is a registered trademark in Japan, the U.S.A., the U.K. and many other countries. © 2005 Victor Company of Japan, Limited
Printed in Thailand LWT0278
Thank you for purchasing this JVC product. Before operating this unit, please
read the instructions carefully to ensure the best possible performance.
For Customer Use : Enter below the Serial No. which is located on the body.
Retain this information for future reference. Model No. Serial No.
- The illustration shows the GY-HD100/GYHD101 HD CAMERA RECORDER with the provided lens, viewfinder, Microphone and battery pack attached.
LWT0278
Downloaded from: https://www.usersmanualguide.com/
Important Safety Instructions
1. Read all of these instructions. 2. Keep these instructions. 3. Heed all
warnings. 4. Follow all instructions. 5. Do not use this apparatus near water.
6. Clean only with dry cloth. 7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions. 8. Do not install
near any heat sources such as radiators, heat resisters, stoves, or other
apparatus (includ-
ing amplifiers) that produce heat. 9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a
third grouding prong. The wide blade or the third prong are provided for your
safety. If the povided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. 10. Protect the power cord
from being walked on or pinched particularly at plug, convenience receptacles,
and the point where they exit from the apparatus. 11. Only use
attachments/accessories specified by the manufacturer. 12. Use only with the
cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury tip-over. 13. Unplug this apparatus
during lightning storms or when unused for long periods of time. 14. Refer all
servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug id
damaged, liquid has been spilled objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
I
Downloaded from: https://www.usersmanualguide.com/
Important Safety Instructions
FOR USA AND CANADA
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
INFORMATION FOR USA
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmfull interfrence to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: z Reorient or relocate the receiving antenna. z
Increase the separation between the equipment and
receiver. z Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. z Consult the dealer or an
experienced radio/TV technician for
help. CAUTION: CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA)
This Class B digital apparatus complies with Canadian ICES003.
Cet appareil numerique de la Class B est conforme a la norme NMB-003 du
Canada.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
This unit should be used with 7V DC only. CAUTION: To prevent electric shocks
and fire hazards, do NOT use any other power source.
NOTE: The rating plate (serial number plate) is on the bottom of the unit.
CAUTION: To prevent electric shock, do not open the cabinet. No user
serviceable parts inside. Refer servicing to qualified service personnel.
AVERTISSEMENT : POUR EVITER LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS
EXPOSER L’APPAREIL A L’HUMIDITE OU A LA PLUIE.
Ce magnétoscope ne doit être utilisé que sur du courant direct en 7V.
ATTENTION : Afin d’eviter tout resque d’incendie ou d’électrocution, ne pas
utillser d’autres sources d’alimentation électrique.
REMARQUE: La plaque signalétique (plaque du numéro desérie) est située sur le
cadre inférieur de l’unité.
Due to design modfications, data given in this instruction book are subject to
possible change without prior notice.
The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed close to the
apparatus.
Worded – “CAUTION – Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.”
II
Important Safety Instructions
FOR EUROPE
This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments: z residential area (in houses) z commercial and light industry; e.g. offices or theatres z urban outdoors In order to keep the best performance and furthermore for electromagnetic compatibility we recommend to use cables not exceeding the following length:
Camera
Port DC IN INPUT1/2 LINE OUTPUT PHONES 1/2 VIDEO/Y,PB,PR IEEE1394 (HDV/DV)
Cable Exclusive Cable Shielded Cable Shielded Cable Shielded Cable Shielded Cable Exclusive Cable
Length 2 m 3 m 1.5 m 2 m 3 m 4.5 m
AC ADAPTER
Port
Cable
Length
DC OUT
Exclusive Cable
2 m
AC IN
Exclusive Cable
2 m
The inrush current of the apparatus is 7 amperes.
Caution: Where there are strong electromagnetic waves or magnetism, for example near a radio or TV transmitter, transformer, motor, etc., the picture and the sound may be disturbed. In such case, please keep the apparatus away from the sources of the disturbance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
This unit should be used with 7V DC only. CAUTION: To prevent electric shocks
and fire hazards, do NOT use any other power source.
NOTE: The rating plate (serial number plate) is on the bottom of the unit.
CAUTION: To prevent electric shock, do not open the cabinet. No user
serviceable parts inside. Refer servicing to qualified service personnel.
Due to design modifications, data given in this instruction book are subject
to possible change without prior notice.
The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed close to the
apparatus.
Worded – “CAUTION – Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.”
Caution for AC Mains Lead FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
Appropriate mains cable must be used in each local area, since the other type
of mains cable is not suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K. ONLY
If the plug supplied is not suitable for your socket outlet, it should be cut
off and appropriate one fitted.
III
Downloaded from: https://www.usersmanualguide.com/
Thank you for purchasing the JVC GY-HD100U, GY-HD100E and GY-HD101E HD CAMERA RECORDER. These instructions are for the GY-HD100U, GY-HD100E and GY-HD101E. The text mainly deals with the GY-HD100U and GY-HD101E. Explanations concerning unique GY-HD100U and GYHD101E functions are set off by the (GY- HD100U/GYHD101E only) notice. Information applicable only to the GY-HD100U is marked by “(U model only)”. Information applicable only to the GY-HD100E and the GYHD101E is marked by “(E model only)”. (HDV/DV signal input is possible with the GY-HD100U/GYHD101E.)
ACCESSORIES
Lens
Microphone
/
This unit is a HDV/DV video system format camera recorder. Videocassettes
marked with the A symbol can be used.
The following phenomena may occur when tapes recorded on other units
(including another GY-HD100) are recorded or played back on this camcorder. ·
The transient section between scenes recorded on other
units and those recorded on this unit may appear disturbed. · Digital noise
may appear during playback due to tracking errors.
· This unit records and plays back in the SP mode. Recording or playback in
the LP mode is not possible. (In DV format)
· Due to manufacturing dispersion of tapes, we recommend not to record
pictures within the first 2 to 3 minutes from the beginning of the tape.
· Before recording important scenes, be sure to perform a test recording and
confirm that both video and audio are recorded correctly.
· Recorded video and audio contents are for private use. Other use may
infringe on the rights of copyright holders.
· JVC cannot assume liabilities that may derive from the impossibility of
normal recording or playback of video or audio due to malfunction of the
camcorder or the videocassette.
Battery pack
AC Adapter
DC Cable
Power Cord For GY-HD100U
Power Cord For GY-HD100E/GY-HD101E
Core Filters
Clamp Filters
For DC Cable (Gray)/View- For Audio/IEEE1394 Cable
finder Cable (Black)
Audio Cable
SD memory card
2
MAIN FEATURES
· This camcorder records in HDV format or DV format.
DV format can record and play back SD (Standard Defini-
tion) video on Mini DV videocassettes.
HDV format can record and play back HD (High Definition)
or SD (Standard Definition) video on Mini DV videocas-
settes.
There are two types of recording formats within HDV for-
mat.
HDV 720p (720 effective scan lines, progressive scan)
HDV 1080i (1080 effective scan lines, interlaced scan)
This camcorder supports HDV 720p format. (HDV 720p,
480p, 576p)
HDV and
are trademarks of Sony Corporation
and Victor Company of Japan, Limited.
· 24p mode shooting function In HDV format, it records in 24p mode. It uses a 2:3:2:3 pulldown when recording to tape and converts the images to 60 frames. Component output is converted to 60 frames during playback as well. 24p DV format video uses a 2:3:2:3 pulldown (24p Mode). A 2:3:3:2 pulldown (24p Advanced Mode) is also supported. It can shoot with the same number of frames as movie film.
· Tapes recorded in the DVCAM format can only be played back (simple playback). Recording in the DVCAM format is not possible. DVCAM is a registered trademark of Sony Corporation.
· Supports 60 Hz/50 Hz HD or HDTV signals Supports both 60 Hz/50 Hz HD or HDTV signals. You can select this in a menu screen.
· Cross-convert video output During playback, you can output converted video from the video output connectors. You can select this in a menu screen.
· Focus assist function Enables easy and accurate focusing during shooting.
· Motion smoothing function During progressive shooting (HDV 30p, 25p, 24p), you can record smoother video than with normal progressive video.
· User buttons added Enables you to switch camera settings instantly to suit the shooting conditions.
· Time code reader/generator The built-in time code reader/generator can be used to record the time code and user’s bits.
· Built-in large 3.5″ color LCD display In addition to displaying the camera image and the playback image, the LCD monitor shows the status screens, menu screens for settings, and alarm indications.
· Built-in monitor speaker for audio checking The input audio can be monitored
in recording or EE mode. The playback sound can be monitored in the playback
mode. The speaker also outputs an alarm tone in case an abnormal condition
occurs in the unit.
· Recording check function for convenient recording review function
· Camera section designed with 3-CCD system for highquality picture 1/3″ 3-CCD
with 1,110,000 effective pixels employed. Digital signal processing for
reproduction of HDV/DV highquality picture.
· Multi-Zone Auto Iris Detection Circuit Multi-zone auto iris detection
circuit ensures optimum iris position even in back light conditions or when a
bright subject moves in a frame.
· Safety Zone indication in viewfinder
· Zebra pattern video level indication in viewfinder
· Full Auto Shooting (FAS) function Eliminating the need for troublesome
switch or filter operations, the FAS function automatically provides a wide
range of compatibility with shooting conditions which varies as you move
between indoors and outdoors or between bright and dark locations.
· ND filters for 1/4ND, 1/16ND provided
· IEEE1394 connector IEEE1394 connector (6-pin) provided. Enables transfer of
digital data to other equipment provided with IEEE1394 connector, such as a
non-linear editing system. (Power cannot be supplied.)
· 1/3″ bayonet type lens
· Camera output, VTR playback output (composite/component) possible
· Built-in color bars (ARIB (multi-format color bars), SMPTE/ EBU type)
· Shutter speeds and menus can be selected using a dial, making it very easy
to use.
· Variable scan shutter There is no flicker when shooting computer screens and
other non-NTSC/PAL format screens.
· Slow shutter Makes it possible to brightly shoot video of dark subjects with
little motion by accumulating the images.
· Backup recording function Continuous extended recording is possible by
connecting to HDV/DV devices.
3
Downloaded from: https://www.usersmanualguide.com/
CONTENTS
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 3
INTRODUCTION
Precautions for Proper Use . . . . . . . . . . . . . . . . . . . . . . . . . 6
Routine and Periodical Maintenance . . . . . . . . . . . . . . . . . . 7
Precautions for Use of Head Cleaning Tape . . . . . . . . . . . . 7 Battery
Pack to be Used . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Videocassette to be Used . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 9 Characteristic CCD Phenomena . . . . . . . . . . . . . . . . . . . . . 9
CONTROLS, INDICATORS AND CONNECTORS
ZOOM Lens (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Front Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 Rear Section . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 12 LCD Door . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 13 Right Side Section . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 14 Left Side Section . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 16 Top Section . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 17 Indications on the LCD Monitor
and in the Viewfinder . . . . 19
PREPARATIONS
Basic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 28 Attaching the Zoom Lens (Provided) . . . . . . . . . . . . . . . . . 29
Attaching the Microphone (Provided) . . . . . . . . . . . . . . . . 29 How to
Attach the Viewfinder . . . . . . . . . . . . . . . . . . . . . . 29 Inserting
an SD Memory Card . . . . . . . . . . . . . . . . . . . . . . 30
· Inserting an SD Memory Card · Taking out the SD memory card · About SD
Memory Cards About the Viewfinder Cable . . . . . . . . . . . . . . . . . . .
. . . . . 30 AC Operation . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . 31 · Charging the Built-in Battery Battery Operation . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 32 · Charging the
Battery Pack · Attaching the Battery Pack on the GY-HD100 · Detaching the
Battery Pack from the GY-HD100 · Remaining Battery Power Display · Battery
Recharge Times · Operating Time with Battery Pack · Precautions for the
Battery Pack · Recharging
PREPARATIONS FOR OPERATION
Turning the Power ON . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
· Turning the Power ON · Turning the Power OFF
Loading/Unloading the Cassette . . . . . . . . . . . . . . . . . . . . .35
Setting and Displaying the Date and Time . . . . . . . . . . . . .36
· Setting the Date and Time Style · Setting the Date and Time · Displaying the
Time and Date on the Screen Displaying Time Code . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .38 Recording Time Codes in Continuation of Time
Codes Recorded on Tape . . . . . . . . . . . . . . . . . . . . . . . . . . .
.39 Presetting and Recording of Time Code . . . . . . . . . . . . . . .39 ·
Presetting time cord data · Presetting user’s bit data Screen Adjustment . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Viewfinder
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Back
Focus Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .42 White
Balance Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .43 · White
Balance Adjustment · Full Auto White Balance (FAW)
SETTING AND ADJUSTMENTS BEFORE SHOOTING
Setting the Video Format . . . . . . . . . . . . . . . . . . . . . . . . . .44
Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .45 Screen Size (4:3/16:9) Mode Selection . . . . . . . . . . . . . . .45
Audio Input Signal Selection . . . . . . . . . . . . . . . . . . . . . . . .46
· Selecting the CH-2 channel input connector · Selecting the audio signal
input · Adjusting Audio during Recording · Monitoring Audio during Recording
CONTENTS
SHOOTING OPERATION
Basic Recording Operation . . . . . . . . . . . . . . . . . . . . . . . . 48 ·
If the Record-Standby Mode Continues · Checking Recorded Contents in Record-
Standby Mode (Recording Check Function)
HEADER REC Function . . . . . . . . . . . . . . . . . . . . . . . . . . 50
PLAYBACK MODE
Playback Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52 Fast-Forward, Rewind . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 52 Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 52 Outputting Audio . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 53
USING EXTERNAL COMPONENTS
Connecting the Video Signal Cables . . . . . . . . . . . . . . . . . 54 ·
Connecting the IEEE1394 Cable · Composite and Component Connections
Dubbing with AV Devices . . . . . . . . . . . . . . . . . . . . . . . . . 55
HDV/DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56 Backup Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 58
MENU SCREENS
Menu Screen Configuration . . . . . . . . . . . . . . . . . . . . . . . . 59
Setting Menu Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60 TOP MENU Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61 VIDEO FORMAT Menu Screen . . . . . . . . . . . . . . . . . . . . . 62
CAMERA OPERATION Menu Screen . . . . . . . . . . . . . . . . 64 CAMERA PROCESS
[1/2] Menu Screen . . . . . . . . . . . . . 65 CAMERA PROCESS [2/2] Menu
Screen . . . . . . . . . . . . . 66 ADVANCED PROCESS Menu Screen . . . . . . .
. . . . . . . . 67 COLOR MATRIX ADJUST Menu Screen . . . . . . . . . . . . .
68 SKIN COLOR ADJUST Menu Screen . . . . . . . . . . . . . . . . 68 SWITCH
MODE Menu Screen . . . . . . . . . . . . . . . . . . . . . 69 AUDIO/MIC Menu
Screen . . . . . . . . . . . . . . . . . . . . . . . . . 70 LCD/VF [1/3] Menu
Screen . . . . . . . . . . . . . . . . . . . . . . . . 71 LCD/VF [2/3] Menu
Screen . . . . . . . . . . . . . . . . . . . . . . . . 72 LCD/VF [3/3] Menu
Screen . . . . . . . . . . . . . . . . . . . . . . . . 73 TC/UB/CLOCK Menu
Screen . . . . . . . . . . . . . . . . . . . . . . 74 HEADER REC Menu Screen .
. . . . . . . . . . . . . . . . . . . . . . 75 TIME/DATE Menu Screen . . . . .
. . . . . . . . . . . . . . . . . . . . 76 OTHERS [1/2] Menu Screen . . . . .
. . . . . . . . . . . . . . . . . . 77 OTHERS [2/2] Menu Screen . . . . . . .
. . . . . . . . . . . . . . . . 78 FILE MANAGE Menu Screen . . . . . . . . . .
. . . . . . . . . . . . 79
· Loading a menu settings file · Saving settings · Resetting the menu settings
to the factory settings · Initializing (formatting) an SD memory card
FEATURES OF THE CAMERA SECTION
How to Use Skin Detail . . . . . . . . . . . . . . . . . . . . . . . . . . .
.82 Outputting color bars . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .84
OTHERS
Warnings and Responses . . . . . . . . . . . . . . . . . . . . . . . . . .85
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .88 How to Display the Hour Meter . . . . . . . . . . . . . . . . . . . . .
.89 Information for Users on Disposal of Old Equipment . . . . .89
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .90
· EXTERNAL DIMENSIONS
4
5
Downloaded from: https://www.usersmanualguide.com/
INTRODUCTION
Precautions for Proper Use
· Supply voltage Make sure that the power is between 6.5 V and 7.9 V DC. If
the power voltage is too low, abnormal color and increased noise may occur. Do
not exceed 7.9 V DC in any case, or the unit could be damaged.
· Allowable ambient temperature and humidity Be sure to use the unit within
the allowable temperature range of 0°C to 40°C and a relative humidity of 30%
to 80%. Using the unit at a temperature or humidity outside the allowable
ranges could result not only in malfunction but the impact on the CCD elements
could be serious as small white spots may be generated.
· Strong electromagnetic waves or magnetism Noise may appear in the picture or
audio and/or the colors may be incorrect if the camera is used near a radio or
television transmitting antenna, in places where strong magnetic fields are
generated by transformers, motors, etc., or near devices emitting radio waves,
such as transceivers or cellular phones.
· Use of wireless microphone near the camera When a wireless microphone or
wireless microphone tuner is used near the camera during recording, the tuner
could pick up noise.
· Avoid using or placing the unit in places; · subject to extreme heat or
cold; · with excessive dirt or dust; · with high humidity or moisture; ·
subject to smoke or vapour such as near a cooking stove; · subject to strong
vibrations or on an unstable surface; · also do not leave the unit for long
hours in a parked car under direct sunlight or near room heating equipment.
· Do not leave the unit where it is subject to radiation or xrays or where
corrosive gasses occur.
· Protect the unit from being splashed with water (especially when shooting in
the rain).
· Protect the unit from being wet when shooting on a beach. In addition, salt
and sand may adhere to the camera body. Be sure to clean the camera after use.
· Protect the unit against penetration of dust when using it in a place
subject to sandy dust.
· Optical performance of lens Due to the optical performance of the lens,
color divergence phenomena (magnification chromatic aberration) may occur at
the periphery of the image. This is not a camera malfunction.
· Noise may appear in the viewfinder when switching between the playback
picture and the EE picture.
· Use the unit in an upright position. If placed on its side, heat release
efficiency will deteriorate, adversely affecting the tape transport. Depending
on circumstances the tape may also be damaged.
· Vibrations Colors may fail to appear and/or the image and sound may be
disturbed during VTR playback in locations subjected to strong vibrations.
· Precautions for transportation Do not drop or hit the unit against a hard
object.
· Remove the videocassette before transporting the unit. · Do not insert an
object other than a videocassette in the
cassette insertion slot. Be sure to close the cassette cover when the unit is
not to be used for a long period.
6
· Do not set the POWER switch to OFF or remove the power cable during
recording or playback. Otherwise the tape may be damaged.
· The sensitivity level of the provided microphone is set lower than the
reference input (60 dBs) setting.
· When the unit is not in use, be sure to set the POWER switch to OFF in order
to reduce power consumption.
· Cleaning the body: Wipe body with a dry, soft cloth. To prevent deformation
of the body, etc. and to avoid operation hazards, do not allow volatile
liquids such as benzine and thinner to touch the body, and do not wipe it with
a cloth soaked in such a liquid. When it is extremely dirty, soak the cloth in
a solution of neutral detergent, wipe the body with it, and then use a clean
cloth to remove the detergent.
· The camera may not show stable pictures in the period immediately after the
power is turned on, but this is not a malfunction.
· A sound occurs when the built-in head cleaner that runs when you load or
eject a videocassette operates, but this is not a malfunction.
· The LCD monitor and the viewfinder screen The LCD monitor and the viewfinder
screen are manufactured using high-precision technology. Black spots may
appear on the LCD monitor and the viewfinder screen, or red, blue, green
and/or white spots may not turn off. However, this is not a malfunction and
these spots are not recorded on the tape.
· If you use the camcorder continuously for a long period of time, the
characters displayed in the viewfinder may temporarily remain on the screen.
This is not recorded on the tape. In addition, they are no longer displayed if
you turn the power off and then on again.
· If you use the camcorder in a cold location, the images may appear to lag on
the screen, but this is not a malfunction. This is not recorded on the tape.
· Do not insert fingers or foreign objects into the cassette insertion slot as
this may result in personal injury or damage to the mechanism.
· Use the provided AC adapter for the power supply. · Use the specified power
cord (accessory).
Using a power cord other than the one specified or using a damaged cord will
result in a fire or electric shock. · Do not use the provided power cord with
a device other than this one. · To prevent damage to the connectors, use the
camcorder with the connector covers on when you are not using the video signal
output connectors.
CAUTION
· Do not point the lens or viewfinder directly at the sun or other strong
light source. · Eye damage could result. · If the lens or viewfinder is left
pointed at the sun, rays may collect inside the unit and cause damage or a
fire.
· When carrying the camera, be sure to hold the carrying handle. Holding the
lens or viewfinder may result in damage.
INTRODUCTION
Routine and Periodical Mainte-
nance
The GY-HD100 incorporates precision mechanical parts, which will collect dirt,
wear out and deteriorate as the unit is used. After the unit has been used for
a long period even in a normal environment, the heads, drums and tape
transport mechanisms also collect dirt. Especially, dust which penetrates the
inside of the VTR section during outdoor use will promote the wear and
deterioration of mechanical parts by causing poor contact between tape and
heads or failing to maintain the video and audio quality at high levels. To
prevent wear and deterioration, clean the mechanical parts using a head
cleaning tape as routine maintenance. However, cleaning with a head cleaning
tape alone is not enough for cleaning the entire tape transport mechanism, so
it is also recommended to apply periodical maintenance (inspection) to prevent
the sudden occurrence of failure. As the replacement, adjustment and servicing
of parts require advanced skill and equipment, please consult the person in
charge of professional video equipment at your nearest JVC-authorized service
agent.
Head Cleaning
· To maintain beautiful pictures and sound, be sure to use a head cleaning
tape to clean the head periodically. (X See “Precautions for Use of Head
Cleaning Tape”.) If headcleaning is not performed periodically, a type of
mosaic noise called block noise may appear in the picture or sound may be
interrupted.
Block Noise
· Please use cleaning tape produced by JVC. Do not use head cleaning tapes
other than specified. X See “Precautions for Use of Head Cleaning Tape” about
how to use the head cleaning tape and precautions for use of the head cleaning
tape.
· When dust adheres to the heads, the warning message “HEAD CLEANING
REQUIRED!” is displayed on the LC monitor and in the viewfinder during
playback, edit search, and recording check using the RET button on the lens
section.
Periodical Maintenance
Contents : Check or replace the following mechanical parts according to the
running time.
Usage Time
500H 1000H
Drum assembly (including heads)
G
E
Tape guides, rollers
G
E
Belt gears
H
E
Drive parts
H
H
G: Clean, check and adjust. E: Clean and check. Replace as required. F: Replace.
1500H
E
E E E
2000H
F
F F F
· The maintenance contents vary depending on the operating environment and
method. Therefore, the above data should be considered as a reference.
Time management The accumulated running time of the unit can be confirmed with
the hour meter display (which shows the accumulated drum and fan motor running
time). X See “How to Display the Hour Meter” on page 89.
For consultations related to the maintenance planning or cost, please contact
the person in charge of professional video equipment at your nearest JVC-
authorized service agent.
Precautions for Use of Head Cleaning Tape
Please use cleaning tape produced by JVC. Adhere to the following precautions
when using the head cleaning tape.
1. Insert the cleaning tape.
Press the PLAY/STILL button after the cleaning tape is fully loaded. The tape
runs for 10 seconds at a time in the PLAY mode. (The tape stops automatically
and then the unit enters the STOP mode.)
2. Do not use the tape more than four times at the most for
each cleaning.
Use the following chart as a guide for periodical head cleaning.
Running
Low temperature
Room temperature
High temperature
Operating envi- 0°C to 10°C ronment
10°C to 35°C 35°C to 40°C
Yardstick for 1 to 2 times ev- 1 to 2 times ev- 1 to 2 times ev-
use of cleaning ery 5 hours
ery 20 to 30 ery 5 hours
tape
hours
Note 1) Note 2)
Note 3) Note 4)
Note 5)
When used in a low humidity environment, head cleaning should be conducted at intervals half of those given in the below chart. If an M-DV80 tape is used immediately after head cleaning, the “HEAD CLEANING REQUIRED!” indicator may remain on. In this case, let the tape run as the indicator will turn off after the tape has run for a while. Use the cleaning tape in the room temperature (10°C to 35°C). The cleaning tape case contains instructions for use of the cleaning tape. However, some of these instructions differ from the contents of this sheet. When using the cleaning tape, please follow the instructions of this sheet. If the “HEAD CLEANING REQUIRED!” does not disappear after repeated head cleanings, the recording tape may be abnormal. Avoid excessive repeated use of the head cleaning tape.
7
Downloaded from: https://www.usersmanualguide.com/
INTRODUCTION
Battery Pack to be Used
The GY-HD100 can use any of the following batteries. · BN-V428, BN-V438
Videocassette to be Used
· Use JVC’s videocassette tapes marked with the A symbol.
· Mini DV videocassette : M-DV63HD M-DV63PROHD
- Do not use M-DV80. · Videocassettes cannot be used upside down. · Avoid storing a videocassette with its tape not being com-
pletely wound, as this may damage the tape. Rewind it to the beginning before placing a cassette into storage. · Store videocassettes in a place with little humidity and good ventilation where mould does not form. · After a videocassette tape has been used repeatedly, it becomes unable to maintain full performance due to an increase in noise caused by dropouts, etc. Do not continue to use a dirty or damaged tape, as this will reduce the rotary head life. · Videocassette tapes with the A symbol are provided with a switch on the back to prevent accidental erasure. · Slide the switch to SAVE to protect the required recording in the tape from being overwritten. · To record on the tape, slide the switch to REC.
Switch
For recording and storing videotapes in the best condition
Observe the following instructions for the best recording and storage of
videotapes. · Take care of the conditions of handling videotapes. It is rec-
ommended that you record and store videotapes in the environment below.
Temperature Humidity
Hourly temperature change
Hourly humidity change
Recording
17°C to 25°C 30% to 70%
Less than 10°C
Less than 10%
Storage
Short period (Up to 10 years)
Long period (Over 10 years)
15°C to 23°C 15°C to 19°C
40% to 55% 25% to 35%
H
H
H
H
· Do not leave the videotapes neglected for a long period. If videotapes are
left wound for a long period of time, it may result in distortion of the tape.
Also it may cause tape-totape adhesion (known as blocking). It is recommended
that videotapes be unspooled and rewound once a year for refreshing.
· When tapes are not in use, store them in cases and on end. Storage cases
protect videotapes from humidity, dust and ultraviolet light. Keep tapes in
cases and do not store them lying flat. When housed in a horizontal position,
pressure from other tapes can cause distortions and deformations of the tape
edges.
INTRODUCTION
Condensation
· If the unit has been cooled down in a cold place and is then carried to a warm place, the moisture contained in the warm air may adhere to the head drum or tape guides and be cooled into water droplets. This phenomenon is referred to as condensation (dewing). When this occurs, the head drum and tape guides are covered with droplets allowing the tape to be stuck to them, leading to tape damage.
· Condensation occurs in the following cases: · When the unit is suddenly moved from a cold place to a warm place. · When a room heater has just started or when the unit is exposed directly to cold air from an air conditioner. · When the unit is placed in a very humid place.
Head drum Video tape
Do not leave the videocassette inserted when moving the camera under conditions where the temperature environment changes. After moving the unit, do not use until the internal parts have stabilized.
· “CONDENSATION ON DRUM” is displayed on the LCD monitor and in the viewfinder when condensation occurs in this unit.
Characteristic CCD Phenomena
Smear and Blooming Due to the physical structure of a CCD it is possible to
induce vertical streaking (called “smear”) when shooting an extremely bright
light source. Another effect is the expansion of light around a bright light
or object (called “blooming”). The CCD employed in this unit is characterized
by inducing very little smear or blooming. Nevertheless, please take note that
smear or blooming may be induced when shooting a bright light source.
Smear Vertical pale streaking appearing at high luminous object
Monitor screen
High luminous object (Electric light, sunlight, etc.)
Blooming Blurring in highlight
Moire or Aliasing Shooting stripes or fine patterns may cause a jagged effect
or a banding in fine mesh patterns.
White dots High temperatures can cause CCD sensor pixels to produce the effect
of white dots in the image. This condition is conspicuous especially when gain
is applied. This is a characteristic of the charged-coupled device (CCD). As
far as possible, use the unit under conditions where the temperature of the
unit does not increase.
Keep the power on until the warning message disappears. · Pay attention to
condensation even before the condensa-
tion indication appears. As condensation forms gradually, the condensation
indication may not appear for the first 10-15 minutes after condensation has
formed inside. In an extremely cold place, the condensation could freeze and
turn into frost. In such a case, it takes an additional 2-3 hours for the
frost to first melt into condensation and then to be dissolved. · To prevent
condensation When moving the unit from one place to another where the
temperatures are greatly deferent, first remove the videocassette, place the
unit in a tightly sealed vinyl bag, and then move it to a new environment. To
ensure no condensation occurs, allow the temperature of the unit in the bag to
reach that of the new environment before using it.
8
9
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
ZOOM Lens (Optional)
Th16 x 5.5BRMU
32
1
RET
M
A
W
T
4
5
6
78 9
0
d
MACRO
ab
c
1FOCUS ring Manual focus ring.
2ZOOM lever/ring This is the manual zoom ring equipped with a zoom lever. To
adjust the zoom manually, turn the zoom mode knob b to position “M”.
3IRIS ring Manual iris ring. To activate the auto iris feature, set the Iris
Mode switch 7 to “A”.
4[VTR] VTR trigger button To start/stop shooting.
5[RET] Return video button You can only monitor the return video signal from
the VTR from the viewfinder, LCD monitor and video signal connector while this
button is pressed. When you set the LENS RET item to “FOCUS ASSIST” in the
SWITCH MODE menu screen, you can use this button as the FOCUS ASSIST button. X
See page 69.
6ZOOM servo control lever To operate the servo zoom feature with this lever,
set the ZOOM knob b to “S”. · Pressing the “W” section of this lever increases
the angle of the lens for a wider shooting angle. · Pressing the “T” section
of this lever narrows the lens angle perspective for telephoto shots. ·
Pushing harder changes the speed of the zoom.
7IRIS mode switch
A : Activates the auto iris feature. M : Allows manual iris control.
8Momentary auto iris button When the IRIS mode switch 7 is at “M”, pushing
this button activates the Auto Iris Function while it is held down only.
9[S] IRIS speed adjusting control For adjusting the iris operation speed.
MEMO
If the speed becomes too fast, hunting may occur. To avoid the phenomena
described above, perform adjustment again. 0FILTER thread Protect the lens
with a clear filter or UV filter by screwing the filter onto the thread inside
the lens hood from the front. Other filters can be used for various effects.
aZOOM servo connector Connect an optional zoom servo unit here. b[ZOOM] ZOOM
mode knob
S : Servo zoom mode. Allows operation by the zoom servo control lever 6.
M : Manual zoom mode. Allows zoom control by the zoom lever/ring 2.
cBACK FOCUS ring/fixing screw For back focus adjustment only. Secure with the
screw knob after adjustment. X See “Back Focus Adjustment” on page 42.
dMacro focusing ring (for close-up shooting) By rotating this ring in the
direction of the arrow, close-up shooting of very small objects becomes
possible. Normal focus adjustment and zooming are not available in the macro
mode. To shoot images in the macro mode, set the focus ring 1 to the infinite
position (f) and the zoom ring 2 to the maximum wide-angle position. To adjust
the focus of the macro image, rotate this ring in the direction of the arrow
until the object is focused.
CAUTION
· The back-focus knob is located close to the macro ring, be careful not to
mistake the back-focus knob for the macro ring.
· After the required operation, be sure to return the macro focusing ring to
the normal position.
X See “Attaching the Zoom Lens (Provided)” on page 29. X See “Back Focus
Adjustment” on page 42.
10
CONTROLS, INDICATORS AND CONNECTORS
Front Section
32
1
4 8
7
5
6
1Shoe Makes it possible to mount separately sold lights and accessories.
2Knob This is the mounting knob for the microphone holder 3.
3Microphone holder Makes it possible to attach the provided microphone or a
separately sold microphone. X See “Attaching the Microphone (Provided)” on
page 29.
4Front tally lamp This lamp lights up when the GY-HD100 enters the record
mode. It blinks during the transition to the record mode. When the tape has
run out, or the VTR enters the warning mode, it blinks quickly. · Use the
FRONT TALLY item on the OTHERS [1/2] menu screen to select whether or not the
lamp should light and the lighting pattern. X See page 77.
5[LENS] Lens control connector Connect 12-pin lens control cable from lens
here.
Pin No.
Function
Pin No.
Function
1 Return switch
7 Iris position
2 VTR trigger
8 IRIS A/R INPUT
3 GND
9 EXTENDER position
4 Lens AUTO/MANU control 10 ZOOM position
5 IRIS control
11
6 +12V DC
12
6[ZEBRA] Zebra switch When this switch is ON, a zebra pattern is imposed on
the viewfinder or LCD areas having luminance levels in accordance with the
menu settings made for the video signal. This pattern can be used as a
reference for manual adjustment of the lens iris. Zebra patterns are also
displayed during color bar display when this switch is set to ON. · The
default value is 70% – 80%. The luminance level can be changed with the ZEBRA
setting in the LCD/VF [1/3] menu screen. X See page 71. While this switch is
pressed to the SKIN AREA side, the color tone areas specified with the SKIN
COLOR ADJUST item on the ADVANCED PROCESS menu are indicated in the
viewfinder. The switch returns to the OFF position when released. X See “How
to Use Skin Detail” on page 82. The Skin Detail color tone areas are not
indicated while the color bar or VTR playback picture is shown in the
viewfinder or on the LCD monitor.
7[AWB] Auto white balance button When the WHT.BAL switch c on page 15 is set
to A or B and you press this button, the white balance is automatically
adjusted. It is not activated in preset, full auto shooting, full auto white
balance and color bar modes. X See “White Balance Adjustment” on page 43.
8Lens mounting ring/Lens lock lever Hold the lens and use the lever to turn
the ring anticlockwise to release lens. To mount lens make sure the lens guide
pin fits well, and then turn the ring clockwise until firm. X See “Attaching
the Zoom Lens (Provided)” on page 29.
11
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Rear Section
3 4
3Shoulder belt hooks
Allows you to attach a separately sold shoulder belt.
4LCD monitor
Shows a color camera image or the VTR playback picture.
It is also used for displaying the following:
· Menu Setting screens
1
· Characters showing the whether the GY-HD100 is set to
shooting mode or VTR playback mode
2
· Date and time and time code
· Audio level meter
· Warning indications, etc. X See page 19.
5Tripod mount
Use this hole when mounting the camera onto a tripod.
(Use a screw shorter than 8 mm.)
Always make sure that the camera is securely mounted.
6Rotation-preventive hole
Use this to prevent the camera from falling off the tripod.
Always make sure that the camera is securely mounted.
6
5
1Back tally lamp This lamp lights up when the GY-HD100 enters the record mode.
It blinks during the transition to the record mode. When the tape has run out,
or the VTR enters the warning mode, it blinks quickly. · Use the BACK TALLY
item on the OTHERS [1/2] menu screen to select whether or not the lamp should
light and the lighting pattern. X See page 77.
2[PHONES] Earphone jack This is a stereo mini-jack for connecting an earphone
for audio monitoring. Plug in an earphone or headphone with a 3.5 mm diameter
plug. The earphone can also be used to monitor alarm tones in accordance with
the circumstances. The audio channel to be output is selected with the AUDIO
MONITOR item on the AUDIO/MIC menu screen and MONITOR SELECT switch e on page
18. The audio output level is adjusted with the Audio monitor volume control 3
on page 14.
MEMO · The volume of the alarm sound is set with the ALARM VR
LEVEL item on the OTHERS [1/2] menu screen. · When using a stereotype jack and
stereo sound should
be output, the following setting should be performed. Set the MONITOR SELECT
switch e on page 18 to BOTH. Set the AUDIO MONITOR item on the AUDIO/MIC menu
screen to STEREO.
12
CONTROLS, INDICATORS AND CONNECTORS
LCD Door
1
5
2
34
1[LCD BRIGHT +/] LCD brightness +/ button This button is for adjusting the brightness of the LCD monitor display. · Pushing the button in the + direction makes the monitor brighter. · Pushing the button in the direction makes the monitor darker. · Pushing the +/ buttons simultaneously returns the setting to the standard setting.
2[CH-1/CH-2 AUDIO SELECT] CH-1/CH-2 audio selector switch Selects the method of adjusting the CH-1 and CH-2 audio channel audio levels.
AUTO MANUAL
: A limiter works to suppress the audio level when excessive audio is input.
When the input level is low, the audio level does not increase. The “AUTO” LED
in the CH-1/CH-2 AUDIO LEVEL area g on page 15 lights.
: Allows you to adjust the audio levels using the CH-1/CH-2 AUDIO LEVEL volume
controls g on page 15. When “ON” is set for the FULL AUTO switch h on page 18,
this becomes “AUTO” mode.
3[TC DISPLAY] TC/UB display switch Selects the contents displayed on the TC counter of the LCD monitor or in the viewfinder. (This switch works when the TC/UB item on the LCD/VF [2/3] menu screen is set to ON.)
TC : Set to this position to display time code values. UB : Set to this position to display the user’s bits values.
4[TC GENE.] Time code generator setting switch Switch for setting the time code generator to preset mode or regeneration mode. It is also used to select the time code run mode when the preset mode is selected.
FREE REC REGEN
: The preset mode is selected, and the time code run mode becomes the FREE run mode. Set to this position to record with the time code or user’s bits set anew (preset). In this setting, the time code always operates in the run mode.
- If this setting is used when recording scenes one after another, the time
codes become discontinuous at the transition points between scenes.
: The preset mode is selected, and the time code run mode becomes the REC run mode. Set to this position to record with the time code or user’s bits set anew (preset). The time code operates in the run mode during recording only. If this setting is used when recording scenes one after another, the time codes are recorded as continuous time codes.
: Regeneration mode, in which the unit reads existing time codes on the tape and records time codes in continuation of the existing ones. Set to this position when you want to add additional time codes to time codes already recorded on the tape.
MEMO
Preset of time code and user’s bits is performed on the TC/
UB/CLOCK menu. X See page 39. X See “TC/UB/CLOCK Menu Screen” on page 74.
5[CAM/VTR] Camera/VTR mode switch button
Each time you press this button, the mode switches
between camera mode and VTR mode. When you do this, the VTR indicator g on page 18 dis-
plays the following statuses.
While the mode is being switched : Flashing
In VTR mode
: Lit
In camera mode
: Off
· Select the Camera mode to record the camera image.
· Select the VTR mode to playback VTR or to input the HDV/DV signal from the IEEE1394 connector 4 on
page 16. (HDV/DV signal input is possible with the GY-
HD100U/GY-HD101E.)
· When the power is turned on, the mode becomes the
Camera mode.
13
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Right Side Section
2
1
54 3
7
6
8 9 0 a
b c
d
VF BRIGHT
USER 1 USER 2 USER 3
ND FILTER 2 1 MENU
STATUS
WHT.BAL
AUTO
AUTO
AUDIO
CH-1 LEVEL CH-2
ON
OFF
POWER
REC
e f gh
j
i
1Monitoring speaker (Ear pad) · In the Camera mode, the input sound can be EE
monitored. In the VTR mode, the speaker outputs the VTR playback sound. The
sound to be output is selected with the MONITOR SELECT switch e on page 18. ·
The sound level is adjusted with the MONITOR sound level volume 3. This
speaker also outputs various warning sounds superimposed on other sound. X See
“Alarm Sound” on page 87.
2Ear pad set screw Screw for adjusting the height of the ear pad.
3[MONITOR] Audio monitor volume control Adjusts the volume of the monitoring
loudspeaker and earphone.
4[VF BRIGHT] Viewfinder brightness adjustment To adjust the brightness of the
viewfinder. X See page 41.
5[PEAKING] Contour adjustment To adjust the contours of the LCD monitor and
viewfinder image. * When the Focus Assist function is running, this control
does not operate. X See page 41.
6[FOCUS ASSIST] Focus assist button When you press this button during
shooting, the area of focus is displayed in blue, red or green, making it easy
to focus accurately. X See “LCD/VF [1/3] Menu Screen” on page 71.
7Clamp Attach the cable from the viewfinder here.
8[USER1/2/3] User buttons You can assign camera functions to the USER1 – 3
buttons. Use them to switch shooting conditions depending upon the subject.
Set them using the USER1 – 3 items in the SWITCH MODE menu screen. X See page
69.
MEMO
· The USER buttons work together with the menu settings. · When a menu screen
is being displayed, they also func-
tion as menu operation buttons. X See “Setting Menu Screens” on page 60.
9[SHUTTER] Shutter/Menu dial · Every time this dial is pressed while in the
normal screen mode (when the menu screen is not displayed), the shutter speed
switches between on/off. · When this dial is turned 1 click up or down in the
normal screen mode, the shutter speed indicator is shown for about 3 seconds
on the LCD monitor or in the viewfinder. The shutter speed is changed when
this dial is turned while the shutter speed indicator is shown. X See page 69.
· When this dial turned upward or downward while the menu screen is displayed,
the cursor (K) also moves upward or downward to allow selection of items in
the menu. To change the setting value of the item, press this dial. When the
setting value starts blinking, turn this dial upward or downward to change the
setting. X See “Setting Menu Screens” on page 60.
0[ND FILTER] ND filter switch Switches the built-in ND filter.
OFF : Turns the filter OFF (FILTER OFF) 1 : Cuts the light intensity to
approximately 1/4. (1/4ND) 2 : Cuts the light intensity to approximately 1/16.
(1/16ND) When you change this switch, the type of the new ND filter is
displayed in the LCD monitor or viewfinder.
CAUTION
If you switch the ND filter while shooting is in progress, the picture may be
disturbed or noise may occur in the audio. X See “Camera Settings” on page 45.
a[STATUS] Status/Menu button · Pressing this button in the normal screen mode
(condition in which the menu screen is not shown) displays a status screen in
the viewfinder or on the LCD monitor. The displayed status screen changes each
time the button is pressed. X See “Status Screens” on page 19. · Pressing this
button for more than 1 second in the normal screen mode displays the menu
screen in the viewfinder or on the LCD monitor. Pressing this button while the
menu screen is displayed in the viewfinder or on the LCD monitor makes the
menu screen disappear. X See “Setting Menu Screens” on page 60.
CONTROLS, INDICATORS AND CONNECTORS
b[GAIN] Sensitivity selector switch Electronically boosts the light sensitivity when there is insufficient illumination on the subject. The boosting level differs depending on the switch position as follows: (Factory presets) L : 0 dB (no boosting is applied) M : 9 dB (boosted to approximately 3 times the original) H : 18 dB (boosted to approximately 8 times the original) · The boosting level for each switch position can be changed with the SWITCH MODE menu screen. X See page 69. The more the boosting level is increased, the more the resulting image will be noisy. · When the FULL AUTO switch h on page 18 is “ON”, this is fixed at “ALC”.
c[WHT.BAL] White balance switch Three white balance modes are selectable with this switch.
B
: Switch into white balance mode memorized in
B. If white balance is performed with the
switch in this position, it will be memorized
into B.
A
: Switch into white balance mode memorized in
A. If white balance is performed with the
switch in this position, it will be memorized
into A.
PRST : Switch into white balance mode (3200K or
(PRESET) 5600K) set in PRESET TEMP. item on the
CAMERA OPERATION menu screen.
X See page 64.
FAW (Full Auto White Balance) mode can be set to A, B or PRESET with the
SWITCH MODE menu screen. X See page 69. In the FAW mode, video color
temperatures are constantly sampled for automatic adjustment to a proper white
balance. · When the FULL AUTO switch h on page 18 is “ON”,
this is fixed at “FAW”.
dStand When attaching the lens, slide the stand forward.
CAUTION
There is a risk that the camcorder will fall onto the viewfinder side when the
lens is not attached, so leave the lens attached even if you are not using it.
e[POWER] Power ON/OFF switch Switch that turns the power ON/OFF. When the
power is OFF, “POFF” is displayed in the LCD monitor or viewfinder. * Wait at
least 5 seconds if you need to turn the power on again.
f[REC] REC trigger button (start/stop recording) Start and stop recording
using this button. (This works together with the REC trigger button on the top
and the lens VTR trigger button.) When “SPLIT” is set for the 1394 REC TRIGGER
item on the OTHERS [2/2] menu screen, this button becomes the start/stop
recording button for an external device. X See page 78. X See “Backup
Recording” on page 58.
g[CH-1/CH-2 AUDIO LEVEL] CH-1/CH-2 Audio level controls and AUTO LED Allow you
to adjust the audio level for the CH-1 and CH-2 audio channels. · To use these
controls, set the CH-1/CH-2 AUDIO SELECT switch 2 on page 13 to “MANUAL”. ·
When the FULL AUTO switch h on page 18 or the CH1/CH-2 AUDIO SELECT switch 2
on page 13 is set to “AUTO”, “AUTO LED” lights. (The audio level controls do
not work.)
h[HDV/DV LED] · In camera mode, this lights according to the setting for the
video format being shot. · In VTR mode, it lights according to the video
format being recorded on tape or the IEEE1394 input video format.
HDV : Lights when the format is HDV. DV : Lights when the format is DV.
MEMO
· During a system error, HDV/DV flash alternately. X See page 86.
· Select whether or not to have this light in the FORMAT LED item on the
OTHERS [1/2] menu screen. X See page 77.
iLCD door lock and release knob To open the LCD door, move this knob on the
direction toward the rear section.
jLCD door LCD monitor door. The LCD monitor is located on the inner side of
the door. The LCD monitor can be viewed when this door is opened. The door can
be turned to change the orientation of the LCD monitor, and it can be rotated
so that it can be accommodated in the main body of the camera. X See page 41.
14
15
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Left Side Section
2 34 5 6
7 8 9
1
b
a
0
1[DC INPUT] DC connector Power input for 7.2 V DC accepts the supplied AC
adapter. X See “AC Operation” on page 31.
2[LINE OUTPUT] Line output connector ()3.5mm) Output connector for audio
signals. · Outputs the input audio signal in the Camera mode. · Outputs the
playback audio signal in the VTR mode. · When a HDV/DV signal (IEEE1394) is
input, the EE sound of the input audio signal is output in the VTR mode. (GY-
HD100U/GY-HD101E only)
MEMO
Alarm sound is not output.
3[IEEE1394] IEEE1394 switch Input/output signal and playback signal video from
the IEEE1394 connector 4. Set this switch according to the format.
HDV : For HDV format DV : DV format
4[IEEE1394] IEEE1394 connector (6-pin) Using an IEEE1394 cable (optional), a
digital video component with IEEE1394 connector can be connected here. X See
“Connecting the IEEE1394 Cable” on page 54. X See “HDV/DV Dubbing” on page 56.
5[VIDEO/Y, PB, PR] Video Signal Output Connectors (RCA) These are connectors
for component or composite video signal output. The signal switches
automatically depending upon the cables connected to these connectors. · You
can select the output signal using the OUTPUT TERMINAL item on the VIDEO
FORMAT menu. You can also select whether or not to add a setup signal in the
SET UP item. X See page 63. · When the OUTPUT CHAR. item on the OTHERS [1/2]
menu screen is ON, the menu setting screen is also displayed in the video from
the video signal output connector. X See page 77. X See “Dubbing with AV
Devices” on page 55.
MEMO
Put the covers on the connectors when you are not using them.
6Cassette cover Sliding the EJECT switch a on page 17 located on the top
section opens this cover to allow insertion or removal of the videocassette.
CAUTION
To prevent foreign objects from entering the internal parts of the VTR unit, do not leave the unit with the cover open for extended periods of time.
7Viewfinder connector (6-pin) Connect the cable from the viewfinder here.
8[CH-2 INPUT] CH-2 audio input connector selector switch Selects the CH-2 audio input connector.
INPUT1 INPUT2
: Inputs the audio from the INPUT1 connector 0 into CH-2.
: Inputs the audio from the INPUT2 connector 0 into CH-2.
MEMO
The audio from the INPUT1 connector is also input into CH-1 regardless of the setting.
9[AUDIO INPUT] Audio input signal selector switch This switch is used to select the input sound signal from INPUT1 or INPUT2 connector.
LINE
MIC MIC+48V
: Set to this position when connected to audio equipment, etc. The reference
input level is +4 dBs.
: Set to this position when the dynamic microphone is connected.
: Set to this position when a microphone requiring +48 V power supply (phantom
microphone, etc.) is connected.
CAUTION
When connecting a component that does not require +48 V power supply, make
sure that the switch is not set to MIC+48V before the component is connected.
MEMO
You can select the normal input level for MIC and MIC+48V in the INPUT1, 2 MIC
REF. item on the AUDIO/MIC menu screen. X See page 70.
0[INPUT1/INPUT2] INPUT1/INPUT2 audio input connectors These are audio input
connectors for connecting to an external audio device or microphone. · Set the
[AUDIO INPUT] switch 9 according to the device to be connected. · Set the CH-2
audio input connector using the [CH-2 INPUT] switch 8. The CH-2 audio from the
set connector is recorded.
aShoulder pad slide button Button to adjust the position of the shoulder pad.
When you press this button, you can move the position of the shoulder pad b
forward or backward.
bShoulder pad
16
CONTROLS, INDICATORS AND CONNECTORS
Top Section
5
6
4 3 2
1
7 8 9
0
e
f
a
g
h b
i
c
j d
k
l
1Viewfinder Displays the camera image and the playback picture.
2Eyepiece Ensures that ambient light does not reach the viewfinder screen or
falls into the eye of the cameraman.
3Eyepiece focus ring You can adjust the focus by turning this ring.
4Eyepiece mounting ring You can adjust the position of the eyepiece forward or
backward by loosening this ring.
5Slide mounting ring You can adjust the position of the viewfinder left or
right by loosening this ring.
6Clamp Attach the microphone cable here.
7[FOCUS ASSIST] Focus assist button When you press this button during
shooting, the area of focus is displayed in blue, red or green, making it easy
to focus accurately. X See “LCD/VF [1/3] Menu Screen” on page 71.
8[REC] REC trigger button (start/stop recording) Start and stop recording
using this button. (This works together with the REC trigger button on the
right panel and the lens VTR trigger button.)
9[REC LOCK] REC LOCK switch Slide this switch in the direction of the arrow to
lock the [REC] trigger button 8. Use this to prevent unwanted recording. (The
REC trigger button on the right panel and the lens VTR trigger button are not
locked.)
0SD memory card cover When you open this cover, you can insert and remove the
SD memory card. X See “Inserting an SD Memory Card” on page 30. When an SD
memory card is loaded · You can save, call up and reset the menu settings on
this camcorder. · You can initialize (format) an SD memory card. X See “FILE
MANAGE Menu Screen” on page 79.
a[EJECT] Eject switch and LED Slide this switch to the side to insert or eject
a videocassette tape. The LED lights while ejecting is in progress.
MEMO
· It takes a few seconds before the videocassette is ejected. Do not close the
cassette cover during the eject operation.
· Do not touch the cassette insertion slot or cassette during the eject
operation. This could result in damage.
bOperation cover Open this cover when operating in the playback mode.
Otherwise, keep this cover closed. This cover can be opened by sliding it to
the side.
MEMO When the STOP button i is pressed in the Camera mode to set the VTR
operation mode indicator to indicate STOP, playback operations become
possible.
c[BATTERY RELEASE] Battery pack lock release lever Slide this lever forward to
remove the battery pack.
dBattery pack Attach the provided battery pack (BN-V428). X See “Battery
Operation” on page 32.
17
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Top Section (Cont’d)
e[MONITOR SELECT] Audio monitor selector switch
This switch is used to select the monitor sound output and playback sound output from the monitoring speaker 1 on page 14 or the PHONES jack 2 on page 12.
CH-1 : The CH-1 channel audio is output. BOTH : CH-1 and CH-2 channel audio
are output mixed.
When this setting is selected, the menu screen can be used to select whether
the mixed sound or stereo sound should be output via the PHONES
jack. (AUDIO MONITOR item on the AUDIO/MIC menu screen)
CH-2
When AUDIO MONITOR item on the AUDIO/MIC menu screen is set to “STEREO”, only the audio of CH-1 is output from the monitoring speaker. : The CH-2 channel audio is output.
X See “Outputting Audio” on page 53. X See “AUDIO/MIC Menu Screen” on page 70.
CAUTION
Make sure to move switches all the way. Do not leave a switch stopped in a
midway position. Noise will be generated and operation irregularities will
occur.
f[DISPLAY] Display button Each time you keep pressing the DISPLAY button about
2 seconds, switch LCD monitor display and viewfinder display.
g[VTR] VTR indicator This indicator lights when the camera is in the VTR mode.
To perform VTR playback or to input the HDV/DV signal from the IEEE1394
connector 4 on page 16, press the CAM/VTR button 5 on page13 to turn on this
indicator. It flashes when the mode is being changed. (DV signal input is
possible with the GY-HD100U, GYHD101E.)
h[FULL AUTO] Full auto shooting (FAS) switch This is the ON/OFF switch for FAS
mode. · During FAS mode, “FAS” is displayed on the LCD monitor or the
viewfinder. · FAS mode works together with the auto iris and auto level
control (ALC) modes and automatically adjusts to the optimal video signal
level and white balance. · The audio recording level sets to automatic
adjustment mode. · Even if there are color bars, this automatically sets to
camera video. · SMOOTH TRANS mode does not run. X See page 64. · Auto iris
mode operates even if the lens iris mode switch is set to the manual position.
· The gain changes continuously until it reaches the maximum ALC MAX setting,
and the shutter speed also changes continuously. · When you release FAS mode,
all of the settings return to their previous modes.
CAUTION
When the power is turned on while the camera is in the FAS mode, it takes
about 10 seconds before the automatic adjustment of FAS is completed. All of
the previous setting contents are recalled when the FAS mode is cancelled.
i[STOP] Stop button Press to enter the stop mode.
j[REW] Rewind button Press this button to rewind the tape. · Pressing this
button in the stop or fast forward mode initiates the rewind mode. (Only for
VTR mode) · Pressing this button during playback, still picture playback or
forward search initiates reverse search.
k[PLAY/STILL] Play/still button Press to start playback. Press to enter the
still picture mode during playback, in the stop mode or in the search mode.
Depending on the ambient temperature, if still image playback mode continues
for between 30 seconds and 3 minutes, it stops automatically. (Tape protect
mode) During still picture playback and search mode, press this button to
return to the normal playback mode. * If the auto tracking is active at the
moment the play mode is entered, the playback video will be interfered with
digital noise.
l[FF] Fast forward button Press this button to fast forward the tape. ·
Pressing this button in the stop or rewind mode initiates the fast forward
mode. (Only for VTR mode) · Pressing this button during playback, still
picture playback or reverse search initiates forward search.
CONTROLS, INDICATORS AND CONNECTORS
Indications on the LCD Monitor and in the Viewfinder
In addition to showing the EE image and the playback picture, the LCD monitor
and viewfinder are also used for the following character displays. To show
characters on the LCD monitor, press the DISPLAY button briefly.
DISPLAY button
USER 1 USER 2 SHUTTER
ND FILTER
2 1
MENU OFF
USER 3
STATUS
WHT.BAL
AUTO
AUTO
STATUS button
· CAMERA MODE (display example)
STATUS 0
STATUS 1
Status screens (screens for checking the current camera settings)
Auto white display (only displayed in the Camera mode)
Menu setting screens Alarm message display Safety zone display (only displayed
in the Camera
mode)
MEMO
When the OUTPUT CHAR. item on the OTHERS [1/2] menu screen is ON, the menu
setting screen is also displayed in the video from the video signal output
connector.
Status Screens
Press the STATUS button while normal screen is displayed to show one of the
status screens. The contents of the status display are divided into those for
the Camera mode and those for the VTR mode. · Each time the STATUS button is
pressed in the Camera
mode, one of 5 status screens is displayed. (STATUS 0, 1, 2, 3, 4) · One type
of screen is displayed in the VTR mode.
MEMO
· When the STATUS button is pressed for 1 second or longer, the menu setting
screen is displayed. To display the Status screen while the menu setting
screen is displayed, press the STATUS button to return to the normal screen.
· You can switch between the LCD monitor and the viewfinder by holding down
the DISPLAY button for about 2 seconds.
STATUS 4
STATUS 2
· VTR MODE (display example)
STATUS 3
STATUS
18
19
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Indications on the LCD Monitor and in the Viewfinder (Cont’d)
Status Screens in the Camera Mode
1
9
8 7 6 5 4
2
3
STATUS 0 Screen
· STATUS 0 1 Event Indication When the Gain or Shutter Speed is changed
manually, the setting condition is displayed for about 3 seconds at the time
the change is made.
Setting Status
Contents of Indications
Gain value was changed
GAIN 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB, 18 dB
Gain value reached the ALC
GAIN ALC
FULL AUTO was turned ON/OFF
FULL AUTO ON, FULL AUTO OFF
ZEBRA was turned ON/OFF
ZEBRA ON, ZEBRA OFF
Shutter speed value was changed *1
SHUTTER 1/6, 1/6.25, 1/7.5, 1/12, 1/12.5, 1/15, 1/24, 1/25, 1/30, 1/48, 1/50, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000,1/4000, 1/10000
Variable shutter speed value was changed *1 V. SHUTTER 1/24.01 to 1/1998.0
Shutter was turned OFF
SHUTTER OFF [1/*] 4
White balance value was changed
(Example) WHITE BAL A <3200K> Numeric value: Any of 2300, 2500, 2800, 3000,
3200, 3400, 3700, 4300, 5200, 5600, 6500,
8000
FILTER value was changed
FILTER OFF, FILTER ND 1 [1/4ND], FILTER ND 2 [1/16ND]
AE LEVEL value was changed *2
AE LEVEL 3, 2, 1, NORMAL, +1, +2, +3
BLACK gain value was changed *2
BLACK NORMAL BLACK STRETCH 1, 2, 3 BLACK COMPRESS 1, 2, 3
PRESET TEMP. value was changed 2 3
WHITE BAL PRST <3200K>, WHITE BAL PRST <5600K>
HEADER REC is running
HEADER REC
FOCUS ASSIST was turned ON/OFF
FOCUS ASSIST ON, FOCUS ASSIST OFF
Timecode was set to zero reset REC LOCK switch was turned ON/OFF
TC ZERO PRESET X See page 40. REC SWITCH LOCKED, REC SWITCH UNLOCKED X See page 17, 9 REC LOCK switch.
A REC command was sent from the IEEE1394 TRIGGER TO HDV, TRIGGER TO DV connector
Other Displays
X See “FILE MANAGE Menu Screen” on page 79-81. X See “Warnings and Responses” on page 85.
1 The range for the shutter speed differs depending on the video format setting. X See page 69. 2 Displayed if functions were assigned to the USER1 – 3 buttons. X See page 69. 3 Displayed when the [WHT.BAL] white balance selector switch c on page 15 is set to PRST (PRESET).
4 ” ** ” depends on the video format.
CONTROLS, INDICATORS AND CONNECTORS
No.
Item
Contents
2 VTR mode indication
STBY : In record standby mode (record-pause mode) REC : During recording PLAY
: During playback FF : During fast forward REW : During rewind STL : During
still picture playback mode FWD : During playback in forward direction (FWD1:
About ×2 speed, FWD2: About ×5 speed, FWD3:
About ×10 speed) REV : During playback in reverse direction (REV1: About ×2
speed, REV2: About ×5 speed, REV3:
About ×10 speed) STOP : Stop mode (Tape protect mode) EJECT : Cassette being
ejected – – – : No tape loaded
3 Indication of date and time
Indicates the date and time. Whether or not the date and time should be displayed as well as the display style are set on the TIME/ DATE menu.
LCD BRIGHT indication
When the brightness of the monitor screen is adjusted with the LCD BRIGHT button, the date and time indications and the VTR mode indication 2 are turned off and the LCD BRIGHT indicator is displayed. (Example) BRIGHT +5 · · · · · + · · · · · O Numeric value: Any of 5, 4, 3, 2, 1, 0, +1, +2, +3, +4, +5.
4 Indication of Black operation B : Displayed when the black stretch or black compress settings are other than NORMAL.
5 Indication of skin tone detail SD : Indicated when skin tone detail is ON. color operation
6 Indication of Iris level opera- I : Displayed when the AE LEVEL setting is other than NORMAL tion
7 Indication of FAW operation FAW : Indicated when Full Auto White Balance is ON.
8 Gain operation indication
- dB : Indicates gain value when gain is other modes than 0 dB and ALC.
9 Indication of various function FOCUS
: Displayed when the Focus Assist function is ON.
operations
SKIN AREA : Blinks while the skin detail color area is displayed.
ALC
: Displayed when ALC function alone is ON.
FAS
: Displayed when the Full Auto Shooting function is ON.
S
: Displayed when the SHUTTER function is ON.
20
21
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Indications on the LCD Monitor and in the Viewfinder (Cont’d)
1
2
3
7
0 4
9
86
5
STATUS 1 Screen
· STATUS 1 In addition to the information on the STATUS 0 screen, this screen displays the following items.
No.
Item
Contents
1 VIDEO FORMAT display
Displays the currently selected video format. Allows you to select the REC item on the VIDEO FORMAT menu screen. X See page 62.
You can switch this display ON/OFF using the FORMAT item on the LCD/VF [2/3] menu screen. X See page 72.
2 Time Code (TC)/User’s Bits Indicates the time code (h:m:s:frame) or user’s bits data.
(UB) indication
(Example) Time code TC 00 : 00 : 00 : 00
3 Remaining tape indication 4 Voltage indication
Colon (:) when non-drop frame mode Dot (.) when drop frame mode
User’s bits UB FF EE DD 20
Whether or not to display this item is set with the TC/UB item on the LCD/VF
[2/3] menu screen. X See page 72. Whether the time code or user’s bits should
be shown is selected with the TC DISPLAY switch inside the LCD door.
Remaining tape indication (displayed in 1-minute steps) This indicator blinks
when remaining tape time is equivalent to less than 3 minutes. Whether or not
to display this item is set with the TAPE REMAIN item on the LCD/VF [2/3] menu
screen. X See page 72. When inserting a brand-new tape, the remaining tape
time is not indicated.
When the tape has been run, the indication will appear. The remaining tape
indication is to be regarded only as a guide. * When the unit is used at low
temperatures, it may take a while before the indication of the remaining tape
time appears.
(Example) 7.0V: Indicates remaining battery level in 0.1V steps.
CONTROLS, INDICATORS AND CONNECTORS
No.
Item
Contents
5 Audio sampling frequency in- 32 K : Indicated when the AUDIO MODE item on the AUDIO/MIC menu screen is set to 32 K. (Audio is
dication
recorded with 12-bit, 32 kHz sampling.)
48 K : Indicated when the AUDIO MODE item on the AUDIO/MIC menu screen is set to 48 K. (Audio is
recorded with 16-bit, 48 kHz sampling.) X See page 70.
6 Audio level meter indication
Displays the CH-1, CH-2 audio level meters. Whether or not to display this item is set with the AUDIO item on the LCD/VF [2/3] menu. X See page 72.
7 Standard audio level indication The level at which audio is recorded on the tape is indicated by “O”.
20 dB, 12 dB X See “AUDIO REF.LEVEL” on page 70.
8 Iris indicator display 9 Iris F-value indication
0 Filter position indication
20 dB
12 dB
OO CH-1 O O O O O · · · + CH-2 O O O O O · · · +
M: Iris set higher than normal b: Iris set to normal N: Iris set lower than normal
Indicates the F-number of the connected lens. OPEN, F2, F2.8, F4, F5.6, F8, F11, F16, CLOSE It is not displayed when the lens is removed. For some lenses, no display appears. The indication can be switched ON/OFF with the F.NO/IRIS IND. item on the LCD/VF [1/3] menu screen. X See page 71.
Indicates the current filter position. No display: FILTER OFF ND1: FILTER ND1 (1/4ND) ND2: FILTER ND2 (1/16ND) The indication can be switched ON/OFF with the FILTER item on the LCD/VF [1/3] menu screen. X See page 71.
22
23
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Indications on the LCD Monitor and in the Viewfinder (Cont’d)
STATUS 2 Screen
STATUS 3 Screen
· STATUS 2 This screen displays the camera setup statuses. Event display is not available while this screen is displayed.
Indication FILE
FULL AUTO GAIN SHUTTER
WHITE BAL AE LEVEL FILTER ZEBRA REMAIN AUDIO
Indication Contents
FILE F CAM1 [****], CAM2 [****], and EXT1 – 4 [****] indicates
SUB NAME X See page 7981. A F symbol is displayed when a menu setting read
from LOAD FILE was changed. The display disappears when the setting is saved
using STORE FILE.
ON, OFF
0dB, 3dB, 6dB, 9dB, 12dB, 15dB, 18dB, ALC
(When STEP is selected) OFF, 1/6, 1/6.25, 1/7.5, 1/12, 1/12.5, 1/15, 1/24,
1/25, 1/30, 1/48, 1/50, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000 (When VARIABLE is selected) 1/24.01 – 1/1998.0 (Displayed when
FAS or ALC mode is selected) EEI The range for the shutter speed differs
depending on the video format. X See page 69.
A<##00K>, B<##00K>, PRESET<##00K>, FAW
3, 2, 1, NORMAL, +1, +2, +3
OFF, ND1 (1/4ND), ND2 (1/16ND)
60-70%, 70-80%, 85-95%, OVER 95%, OVER 100%
Displays the remaining tape (minutes) and the type of tape (Ex: 60MIN (Y)) Y
(Mini DV Videocassette) Displays the audio sampling frequency and the audio
level adjustment mode (Ex: 32K (CH1 Z CH2 a) Z (for AUTO mode) a (for MANUAL
mode)
· STATUS 3 Displays a list of setting statuses for USER1, 2, and 3 as well as LENS RET item on the SWITCH MODE menu screen. X See page 69. Events are not displayed while these statuses are being displayed.
Indication USER1 USER2 USER3
LENS RET
Indication Contents
NONE, BARS, PRESET TEMP., B.STRETCH1, B.STRETCH2, B.STRETCH3, B.COMPRESS1,
B.COMPRESS2, B.COMPRESS3, AE LEVEL+, AE LEVEL NONE, BARS, PRESET TEMP.,
B.STRETCH1, B.STRETCH2, B.STRETCH3, B.COMPRESS1, B.COMPRESS2, B.COMPRESS3 RET,
FOCUS ASSIST
· STATUS 4 This screen only displays VTR mode indication, date and time, event display and alarm indications. * Whether or not date and time should be displayed and the display style are set on the TIME/DATE menu screen. X See “Displaying the Time and Date on the Screen” on page 37.
CONTROLS, INDICATORS AND CONNECTORS
Status Screen in VTR MODE
1
2
3
4 5 6
7
0 9
8
No.
Item
Contents
1 VIDEO FORMAT display
Displays the video format recorded on the tape when in VTR mode. You can switch this display ON/OFF using the VIDEO FORMAT item on the LCD/VF [2/3] menu screen. X See page 72.
MEMO
This camcorder cannot play back or output tape recorded in HDV 1080i format. “INVALID TAPE!” is displayed in the event display area 4.
2 Time code (TC) and user’s bits Displays the time code data being recorded (hour, minute, second, frame) when in VTR mode.
(UB) display
You can switch this display ON/OFF using the TC/UB item on the LCD/VF [2/3] menu screen. X See page 72.
You can select to display either the time code or the user’s bits using the TC DISPLAY switch in the LCD
door.
3 Remaining tape time
Remaining tape indication (displayed in 1-minute steps)
This indicator blinks when remaining tape time is equivalent to less than 3 minutes.
Whether or not to display this item is set with the TAPE REMAIN item on the LCD/VF [1/2] menu screen.
X See page 72.
- When inserting a brand-new tape, the remaining tape time is not indicated.
When the tape has been run, the indication will appear.
-
The remaining tape indication is to be used only as a guide.
-
When the unit is used at low temperatures, it may take a while before the indication of the remaining tape
time appears.
4 Event display
Displays messages related to VTR operations. X See page 85-86.
5 Audio sampling frequency in- The audio sampling frequency used for the recording is displayed during playback.
dication
(32 K, 48 K, 44.1 K)
6 Audio level meter indication Displays the audio level meters during playback.
Whether or not to display this item is set with the AUDIO item on the LCD/VF [2/3] menu screen. X See page 72.
7 VTR mode indication
Indicates the VTR operation status
STBY, STOP, PLAY, REC, FF, REW, FWD, REV, STL, – – – (No tape loaded), SLOW: During variable play-
back in forward direction (Displayed when using non-linear editing software.)
(SLOW+1: About ×0.1 speed, SLOW+2: About ×0.2 speed, SLOW+3: About ×0.5 speed)
During variable playback in reverse direction (Displayed when using non-linear editing software.)
(SLOW1: About ×0.1 speed, SLOW2: About ×0.2 speed, SLOW3: About ×0.5 speed)
8 Time/Date indication
Recorded data are displayed during playback, fast forward, and rewind.
During recording, the data from the IEEE1394 connector is displayed.
(GY-HD100U/GY-HD101E only)
Whether or not the date and time should be displayed and the display style are set on the TIME/DATE menu screen. X See page 76.
When the date and time have not been set, the following indication appears.
– -/- -/- – – -: – -: – –
9 Voltage indication
(Example) 7.0V : Indicates remaining battery level in 0.1V steps.
0 Audio Lock indication
Displayed when the audio signal from DV recording or playback is locked to the video signal.
24
25
Downloaded from: https://www.usersmanualguide.com/
CONTROLS, INDICATORS AND CONNECTORS
Indications on the LCD Monitor and in the Viewfinder (Cont’d)
Auto White Balance Indication (Camera mode only)
The AUTO WHITE indication and the result of the operation are displayed during
the auto white balance adjustment operation. X See “White Balance Adjustment”
on page 43.
Menu Setting Screen
Screen used for making various settings. The Menu Setting Screen appears when
the STATUS button is pressed for 1 second or more. X See “Setting Menu
Screens” on page 60.
TOP MENU screen (Camera mode) Alarm display area
Alarm Message Display
· The following alarm messages are displayed while the STATUS (0, 1, 4) screen
is shown in the Camera mode, or a STATUS screen is shown in the VTR mode. If
an alarm is generated while the STATUS 2, 3 screen is shown, the STATUS 0
screen returns to display the alarm. X See page 85.
· When an abnormality occurs in the VTR, a warning message with an error code
is displayed. X See page 85-86.
Safety Zone Indication (Camera mode only)
The indication of the following safety zone and center mark indications can be
turned ON/OFF with the SAFETY ZONE item and CENTER MARK item on the LCD/VF
[1/3] menu screen. X See page 71. In addition, the safety zone display is on
or off depending on the REC item setting and the ASPECT item setting in the
VIDEO
FORMAT menu screen, as shown below.
SAFETY ZONE
CENTER MARK
REC
ASPECT
DV-60I
DV-24P
4:3
DV-24PA
DV-50I
DV-25P
16:9
HDV-SD60P HDV-SD50P HDV-HD30P HDV-HD25P HDV-HD24P
[16:9]
OFF –
4:3
OFF
ON
14:9
OFF
ON
16:9
OFF
ON
16:9+4:3
OFF
ON
Cannot be selected
26
CONTROLS, INDICATORS AND CONNECTORS
DISPLAY button
Inverted LCD
Normal LCD
LCD BRIGHT
AUDIOSELECT CH-1
CH-2 AUTO MANU
CAM/VTR
TC
DISPLAY TC
GENE.
UB
FREE
REC
REGEN
LCD open 40° or more
LCD close less than 40°
The LCD monitor and the viewfinder (VF) display are on or off depending on whether the LCD monitor is open or closed as well as normal or inverted, as shown below.
LCD Monitor Status LCD Closed Normal LCD
Inverted LCD LCD Open Normal LCD
Inverted LCD
LCD Display OFF ON ON ON
VF Display ON OFF OFF OFF
MEMO
· You can switch between the LCD monitor and the viewfinder by holding down
the DISPLAY button for about 2 seconds.
· After you set up the function that switches the display between the LCD
monitor and the viewfinder by holding down the DISPLAY button, the display
mode is cancelled by the LCD monitor open/close and normal/inverted
operations.
· If the LCD monitor is closed inside the camcorder with the screen in the
normal display orientation, holding down the DISPLAY button does not work.
27
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS
Basic System
SHOULDER BELT
EARPHONE
MICROPHONE
MV-P615U
MV-P618U
3P
FOCUS MANUAL UNIT *1 HZ-FM13 (FUJINON)
HZ-FM15 (CANON)
1/3 ZOOM LENS Th13 × 3.5BRMU (FUJINON)
MICROPHONE
GY-HD100
COMPONENT CABLE RCA pin
COMPOSITE CABLE RCA pin
AUDIO CABLE Stereo-mini RCA pin
MONITOR
MACRO
Wide Converter WCV-82SC
1/3 ZOOM LENS Th16 × 5.5BRMU (FUJINON)
BATTERY BN-V428
FOCUS MANUAL UNIT *1
ZOOM SERVO UNIT HZ-ZS13B
DC cable (2m)
AC
AC ADAPTER
GY-HD100 STANDARD PACKAGE
BATTERY BN-V438
1/2 ZOOM LENS S14 × 7.3B12U (FUJINON) S17 × 6.6BRM (FUJINON) S20 × 6.4B12U (FUJINON) YH16 × 7K12U (CANON) YH19 × 6.7K12U (CANON)
Mount Converter (1/2-1/3) AMC-12
CARRYING CASE
TRIPOD TP-P300
DOLLY TP-P205
IEEE1394 CABLE 6P-6P
*1 An HZ-FM13 cannot be used with a Th16×5.5BRMU or S14×7.3B12/U zoom lens. Use a FUJINON focus manual unit (FMM-8, CFH-3, CFC-12-990). For details, please consult your JVC authorized dealer.
DV VTR
BR-HD50 Non-linear Editing SYSTEM
PREPARATIONS
Attaching the Zoom Lens (Provided)
1. Loosen the mount ring.
2. Attach the lens with its pin aligned with the hole in the
mount.
Pin
3. Tighten the mount ring.
Hole
4. Connect the cable connector.
5. Clamp the lens cable.
Clamp
CAUTION
· Be sure to tighten the mount ring completely. Incomplete tightening may
result in the lens dropping off or disturbed back focus.
· Set the GY-HD100’s power switch to “OFF” before the zoom lens is attached or
detached.
Attaching the Microphone (Provided)
1. 3. Knob
2. Microphone
Microphone holder
5. Clamp
Connect the provided microphone to the microphone holder. Provided microphone
is a phantom microphone.
1. Turn the knob on the microphone holder anticlockwise to
loosen it and open the microphone holder.
2. Place the microphone in the microphone holder.
Place the microphone toward the front to prevent it from interfering with the
cassette cover.
3. Turn the knob on the microphone holder clockwise to
secure the microphone.
4. Connect the microphone cable to the INPUT1 or INPUT2
input connector on the GY-HD100.
5. Attach the microphone cable to the clamp. 6. Make sure to perform the
correct setting for use of a phan-
tom microphone. X See page 46.
4. INPUT1, 2 connector
How to Attach the Viewfinder
Knob Taking off the viewfinder
To attach the viewfinder, slide it in the direction of the arrow.
To take off the viewfinder, pull the knob in the direction of the arrow as you
slide the viewfinder.
28
29
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS
Inserting an SD Memory Card
Cutout SD memory card cover
LOCK switch
By using an SD memory card, you can save and call up menu settings and camera
settings for this camcorder. X See “FILE MANAGE Menu Screen” on page 79. Check
that the POWER switch is OFF.
Inserting an SD Memory Card 1. Open the SD memory card cover. 2. Face the
cutout end of the SD memory card inward and
insert it in the direction of the arrow.
CAUTION Be sure not to touch the metal connector area of the SD memory card.
3. Close the SD memory card cover.
Taking out the SD memory card 1. Push the SD memory card in the direction of
the arrow.
· The SD memory card comes out slightly.
2. Pull the SD memory card straight out.
About SD Memory Cards
· When you use an SD memory card that was either just purchased or formatted
on a device other than this camcorder, format it on this camcorder. X See page
81. Recommended SD memory cards Panasonic: 32 MB or more
· You can write-protect the card so that saved files are not mistakenly
erased. Set the switch on the side of the SD memory card to the “LOCK”
position.
About the Viewfinder Cable
To reduce the emission of unwanted radio waves, be sure to attach the provided
core filter as shown in the figure on the left. z Attach the core filter
(black) as close to the camcorder as
possible, as shown in the figure.
Core filter (black)
AC Operation
POWER lamp
DC IN connector
AC adapter Ferrite core
To plug outlet
DC OUT connector
DC cable
Core filter (gray)
PREPARATIONS
The GY-HD100 is operable with AC power supply or battery pack. Use the
supplied AC adapter as the AC power supply.
1. After making sure that the power switches of the GY-
HD100 and of the AC adapter are set to OFF, connect the DC cable from the AC
adapter to the DC IN connector of the GY-HD100 as shown in the illustration.
2. Press the POWER switch of the GY-HD100 to ON. Power
is supplied to the VTR section and the camera.
CAUTION · When using the DC cable make sure to connect the end
of the cable with the ferrite core to the AC adapter. · Do not remove or
connect the DC cable while recording is
being performed. · Do not use any power source with large fluctuations in the
power source voltage, power sources generating noise, such as ripples or power
sources with lower voltage.
Attach the supplied core filter (gray) as shown in the diagram on the right to
reduce unwanted electromagnetic emission.
z Attach the core filter as shown in the diagram on the left to this unit as
near as possible.
Charging the Built-in Battery
The built-in, rechargeable backup battery retains the date and time and the
time code data. The built-in battery is constantly being charge whenever the
GY-HD100 is connected to a power supply, but it gradually discharges while the
GY-HD100 is disconnected from a power supply. The battery will be fully
discharged when the GY-HD100 is not used for about three months, in which case
the set date and time and time code data are reset. In this case, recharge the
built-in battery and then set the date and time and time code data again.
However, it is possible to use the GY-HD100 even if the builtin battery is
discharged but the date and time and time code data cannot be recorded.
How to charge 1. Connect the provided AC adapter to the GY-HD100 and
an AC outlet or mount a charged battery on the GYHD100.
2. Set the POWER switch on the GY-HD100 to “ON” or
“OFF” (charging takes places with the POWER switch set to either of the
positions.)
3. Leave the equipment in this condition for about 4 hours.
· The built-in battery will remain charged for about 3 months after being
charged for about 4 hours.
30
31
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS
Battery Operation
AC outlet
AC cord
AC adapter
CHARGE lamp 1 POWER lamp CHARGE lamp 2
Connector
32
Battery pack
Battery pack Lock release lever
Charging the Battery Pack
Before use the battery pack should be charged using the provided AC Adapter. *
Be sure to pull the DC cable out of the AC adapter when
you charge the battery.
1. Plug the AC cable of the AC Adapter into an AC outlet.
The POWER lamp illuminates.
2. While pushing the battery pack down, slide it in the direc-
tion of the arrow to mount it on the AC Adapter. Charging starts, and the
CHARGE lamp blinks green. It changes to light steadily when charging is
completed.
3. When charging is completed, remove the battery pack by
sliding it in the opposite direction of the mounting direction.
Attaching the Battery Pack on the GYHD100
If the DC cable is connected to the GY-HD100, unplug the cable.
1. Hold the battery pack with the connector side facing the
GY-HD100.
2. While pressing the battery pack against the GY-HD100,
slide it downward to attach it to the GY-HD100.
Detaching the Battery Pack from the GYHD100
Ensure that the POWER switch on the GY-HD100 is set to OFF.
1. While sliding the battery pack lock release lever, slide the
battery pack upward to remove it.
CAUTION
Do not detach the battery pack while recording is taking place.
MEMO
· Do not connect or disconnect the DC cable while operating with a battery
pack. The following symptoms may occur if the DC cable is connected or
disconnected while operating with a battery pack. · The power is cut off for a
moment when the DC cable is disconnected. · Noise to the video and audio
signals occurs. Audio signal are muted.
· When operation is continued with DC input after the battery pack capacity
has been used up, set the POWER switch to OFF after the DC power is applied.
Then switch ON again.
· If the GY-HD100 is left with the battery pack attached, a small amount of
power is consumed even if the POWER switch on the GY-HD100 is set to OFF.
Remove the battery pack when the GY-HD100 is not going to be used.
PREPARATIONS
Remaining Battery Power Display
LCD monitor/Viewfinder
When the remaining battery power is nearly exhausted, the following warnings
will be generated. Viewfinder screen or LCD monitor
When a Status screen is displayed (excluding the STATUS 2, 3 screen in the
Camera mode) · Alarm indication: LOW VOLTAGE displayed. FRONT and BACK TALLY
lamp on camera: Blinks Monitoring loudspeaker and PHONES jack: Alarm sound
MEMO
After the remaining battery power warnings appear, the GYHD100 automatically
stops operation if the battery power operation is continued.
Battery Recharge Times
Battery pack
Recharging time of a single pack
Successive recharging time of two packs
BN-V428 Approx. 3 hr. 20 min
Approx. 6 hr. 40 min
BN-V438 Approx. 4 hr. 20 min
Approx. 8 hr. 40 min
· When charged at temperatures between 20°C (68°F) and 25°C (77°F).
· When charging battery packs after a long storage period, charging time will
be longer than indicated above.
· When two battery packs are attached, they will be recharged in the order
that they are attached.
Operating Time with Battery Pack
When a fully charged battery pack is attached, the approxi-
mate continuous operating time is as follows
Battery Pack
Continuous Operating Time (at 25°C)
BN-V428
Approx. 40 minutes
BN-V438
Approx. 60 minutes
· Battery operating time may differ depending on the age of the battery pack,
charging conditions and the operating environment, etc. Use the values in the
table on the above for approximate reference times.
· Operating time is reduced in areas with a cold environment.
· Operating time is reduced when the power zoom lens and LCD are used
frequently.
Precautions for the Battery Pack
· When the battery pack is not in use, it must be stored in a cool, dry place.
Do not leave the battery pack in a place where it might be subject to a high
temperature (under direct sunlight in a car, etc.), this could cause leakage
of the fluid or shorten service life.
· When the terminal section of the battery pack gets dirty, the operating time
will be shortened.
· If the operating time becomes greatly reduced even immediately after
recharging, the service life of the battery pack is nearly finished. Purchase
a new battery pack.
Recharging
· Recharge the battery pack after completely discharging it. Repeated
recharging with residual charge remaining could result in reduced battery
capacity.
· If the battery capacity is reduced by repeating incomplete recharging, or
recharging without discharging, once discharge the battery pack completely,
then recharge it to restore the battery capacity.
· If the battery pack is recharged with its internal temperature raised
immediately after use, recharging may not be performed completely.
· Perform charging in an environment where the temperature is between 10°C
(50°F) and 35°C (95°F). 20°C (68°F) to 25°C (77°F) is the ideal temperature
range for charging. If the environment is too cold, charging may not complete.
33
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS FOR OPERATION
Turning the Power ON
CH-1 BOTH CH-2 MONITOR SELECT
DISPLAY
ON OFF
VTR
FULL AUTO
VTR indicator
POWER switch
VF BRIGHT
USER 1 USER 2 SHUTTER
ND FILTER
2 1
MENU OFF
USER 3
STATUS
WHT.BAL
AUTO
AUTO
AUDIO
CH-1 LEVEL CH-2
ON
OFF
POWER
REC
LCD BRIGHT
–
AUDIO SELECT
CH-1
CH-2
AUTO
MANU
CAM/VTR
TC
ProHD DISPLAY GENE.
TC
FREE
UB
REC
REGEN
CAM/VTR button
Turning the Power ON 1. Set the POWER switch to ON.
The unit turns on in Camera mode.
The operation differs according to whether the unit is in the Camera mode or in the VTR mode. The mode switches each time you press the CAM/VTR button. When the mode is switched, the VTR indicator displays the following statuses.
While the mode is being switched : Flashing
In VTR mode
: Lit
In Camera mode
: Off
Camera mode The GY-HD100 enters the Camera mode. The camera image is displayed
in the viewfinder or on the LCD monitor. When a recordable videocassette is
loaded, the GY-HD100 enters the record-standby mode automatically. “STBY” is
displayed in the VTR operation mode indication area of the LCD monitor or in
the viewfinder. In this condition, press the REC/VTR trigger button to start
recording. * Playback is also possible in the Camera mode.
Playback operation becomes possible when the STOP button is pressed to set the
VTR operation mode indicator to indicate “STOP”. VTR mode The GY-HD100 enters
the VTR mode. The camera image will not be displayed in the viewfinder or on
the LCD monitor. When a videocassette is loaded, the GY-HD100 enters the stop
mode. “STOP” is displayed in the VTR operation mode indication area of the LCD
monitor or in the viewfinder. HDV/DV input is possible through the IEEE1394
connector. (GY-HD100U/GY-HD101E only)
Turning the Power OFF 1. Place the GY-HD100 in the record-standby or STOP
mode.
2. Set the POWER switch to OFF. 3. Remove the battery pack or the power
supply to the DC
IN connector. (When the camera is not going to be used for a longer period.)
CAUTION
· Do not set the POWER switch to OFF while recording is taking place. Confirm
that the “STBY” or “STOP” indication is shown in the VTR operation mode
indication area before the power is turned off. Should the POWER switch
accidentally be set to OFF during a recording, wait at least 5 seconds before
turning the power on again.
· Always set the POWER switch to OFF before disconnecting the power supply. Do
not turn the battery pack or AC power supply OFF while the POWER switch on the
camera is still set to ON.
34
Loading/Unloading the Cassette
PREPARATIONS FOR OPERATION
EJECT switch Cassette holder
REC/SAVE switch
Tape window
Cassette cover
Cassette Loading
Use a videocassette tape marked MiniDV. · To record, slide the switch on the
back for use in preventing
accidental erasure to the “REC” side. · Remove any the tape slack before
loading.
1. Turn the POWER switch ON. 2. Slide the EJECT switch on the top panel of
the camcorder
to the side. The videocassette cover opens automatically and a videocassette
tape can be inserted.
3. Insert a videocassette tape into the videocassette holder.
With the tape window facing out, move the switch on the back of the
videocassette up and firmly push the center back of the videocassette straight
in as far as it will go.
4. Carefully push the center of the videocassette cover in the
direction of the arrow as far as it will go to close it. · After the cover is
closed, it takes about 10 seconds until
recording can begin or the camcorder can enter stop mode. If the power is on,
the modes are as shown below.
MODE
REC/SAVE switch
REC
SAVE
Camera Record-standby mode
VTR
STOP mode
STOP mode REC INHIBIT is displayed on the LCD monitor and in the viewfinder.
Unloading the Cassette 1. Turn the POWER switch to ON. 2. When the camcorder
is in shooting standby mode or stop
mode, slide the EJECT switch to the side and wait until the videocassette
cover opens completely. · The LED next to the EJECT switch flashes.
A few seconds pass before the videocassette tape is ejected.
3. The LED turns off and the videocassette cover opens.
· Take out the videocassette tape.
4. Carefully push the center of the videocassette cover in the
direction of the arrow as far as it will go to close it.
CAUTION
· When you close the videocassette cover, push it in firmly as far as it will
go. If the videocassette cover is not closed properly, it becomes half-locked
and the camcorder cannot function. If this happens, firmly push the
videocassette cover in again as far as it will go to lock it.
· Do not slide the EJECT switch while recording is in progress. If you slide
the EJECT switch while recording is in progress, the tape is ejected.
· Do not leave the videocassette cover open for a long time. Dust or dirt may
enter the inside and cause damage.
· Do not touch the videocassette cover or interfere with the eject operation
while ejecting is in progress. This will cause damage.
35
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS FOR OPERATION
Setting and Displaying the Date and Time
- SHUTTER dial
-
STATUS button
USER 1 USER 2 SHUTTER
ND FILTER
2 1
MENU OFF
USER 3
STATUS
WHT.BAL
AUTO
AUTO
AUDIO
CH-1 LEVEL CH-2
ON
OFF
POWER
REC
1. POWER switch
TC/UB/CLOCK menu screen
TIME/DATE menu screen
The date and time of the built-in clock should be set. Powered by the built-in
backup battery the set date and time data continue to count even when the
power is switched off. · The set date and time data are displayed on the LCD
mon-
itor or in the viewfinder and recorded on the tape in accordance with the
settings made on the menu screen.
Setting the Date and Time Style
The date and time are set on the menu screen. When setting while observing on
a monitor connected to the connector, set the OUTPUT CHAR. item on the OTHERS
[1/2] menu screen to ON.
1. Set the POWER switch to ON. 2. Press the STATUS button for 1 second or
longer to dis-
play the TOP MENU screen.
3. Rotate the SHUTTER dial to align the cursor (K) with the
TC/UB/CLOCK item, and then press the SHUTTER dial in the direction of the
camera body. · The TC/UB/CLOCK menu screen appears.
4. Rotate the SHUTTER dial to align the cursor (K) with the
TIME/DATE item, and then press the SHUTTER dial. · The TIME/DATE menu screen
appears. · Set the DISPLAY item on the TIME/DATE menu screen
to ON.
5. Make settings on the TIME/DATE menu screen. (This
includes display style, etc.)
DATE STYLE : Selects the style for displaying the date. YY/MM/DD (Year, month,
day) MM/DD/YY (Month, day, year) DD/MM/YY (Day, month, year)
TIME STYLE : The time can be set to display as a 12hour or 24-hour clock
system.
SEC DISPLAY : To select whether or not indication of seconds should be
displayed on the screen.
TIME SHIFT : Adds time to the built-in clock (time compensation) and displays
it. The adjusted time is also recorded on the tape.
1Rotate the SHUTTER dial to align the cursor (K) with the item to be set, and
then press the SHUTTER dial. · The setting area of the selected item starts
blinking.
2Rotate the SHUTTER dial to change the setting, and then press the SHUTTER
dial. · The setting area stops blinking and the setting is entered.
MEMO
The TIME STYLE, SEC DISPLAY, DATE STYLE and TIME SHIFT items can also be set
and changed after the date and time have been set.
TIME/DATE menu screen
- Date
CLOCK ADJUST menu screen
Time (Hour:Min)
Date
Time
36
PREPARATIONS FOR OPERATION
Setting the Date and Time 1. Display the CLOCK ADJUST menu screen.
Select the CLOCK ADJUST item on the TIME/DATE menu screen.
2. Set the date and time.
The blinking digit is the one to be set. 1When the SHUTTER dial is pressed,
the blinking digit
moves to the next digit. 2When the SHUTTER dial is rotated, the value of the
blinking digit changes. When the SHUTTER dial is rotated upward, the value
becomes higher. When rotated downward, the value becomes smaller. 3Repeat the
procedure described in 1 and 2 above to set the day, month, year, hours,
minutes. The digits indicating seconds cannot be set. 4Press the SHUTTER dial
in sync with a time signal to enter the date and time precisely.
3. When all the settings are completed, rotate the SHUTTER
dial to align the cursor with the PAGE BACK item, and then press the SHUTTER
dial. · The TIME/DATE menu screen returns.
4. To return to the normal screen, use either of the following
methods. Press the STATUS button or Return to the TOP MENU screen and then
select the
EXIT item on the TOP MENU screen before pressing the SHUTTER dial.
Displaying the Time and Date on the Screen
Whether or not the time and date should be displayed on the screen and how to
display them are set on the TIME/DATE
menu screen.
1. Display the TIME/DATE menu screen.
1Select the TC/UB/CLOCK item on the TOP MENU
screen. 2Select the TIME/DATE item on the TC/UB/CLOCK
menu screen.
2. Set the TIME/DATE menu screen.
· DISPLAY item
: Sets whether or not date and time should be displayed. Set to ON to display the indications.
· DISPLAY MODE : Sets the video output mode in
item
which date and time should be dis-
played.
BARS
: Displayed when outputting the color bar.
CAM
: Displayed when outputting the color camera image.
BARS+CAM : Date and time are always displayed.
· DISPLAY STYLE : Sets the style in which the date and
item
time are displayed.
DATE+TIME : Date and time are displayed.
DATE
: Date only is displayed.
TIME
: Time only is displayed.
Display of date and time in the various operation modes.
In Camera mode
: The date and time of the internal
clock are displayed.
In VTR playback mode : The date and time recorded on the
tape are displayed.
In VTR stop mode
: The last read date and time values
are displayed.
When an HDV/DV sig- : Displays the date and time of the
nal is input from the HDV/DV input. (GY-HD100U/GY-
IEEE1394 connector HD101E only)
37
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS FOR OPERATION
Displaying Time Code
LCD/VF [2/3] menu screen
TC DISPLAY switch TC GENE. switch
Time code indication
(Example) Time code indication 00:00:00:00
User’s bits indication FF EE DD 20
STATUS 1 screen
The GY-HD100 records SMPTE-standard (NTSC) or EBUstandard (PAL) time codes and
user’s bits. In the play mode or the record mode, the reproduced time codes or
user’s bits are shown on the LCD monitor or in the viewfinder. · Time code
data cannot be output through the unit’s con-
nectors.
The time codes or user’s bits can be shown on the LCD monitor or in the
viewfinder during playback and recording as follows. (Status screen)
Setting 1. Set the TC/UB item on the LCD/VF [2/3] menu screen to
ON. · Time codes or user’s bit data are displayed on the STA-
TUS screen.
2. Whether time codes or user’s bit data should be displayed
is selected with the TC DISPLAY switch inside the LCD door. TC : Time codes
are displayed. UB : User’s bit data is displayed.
Time code input entered the IEEE1394 connector (GY-HD100U/GY-HD101E only)
Pressing the STOP button for 1 second in the EJECT or stop mode displays the
DV input time code data or user’s bit data from the IEEE1394 connector on the
STATUS screen. DTCG : The time code data from the IEEE1394 connector DUBG :
The user’s bit data from the IEEE1394 connector
To return to display of the original time code or user’s bit, press the STOP
button. (Display of the normal time code or user’s bit is also restored by
performing VTR operation.)
MEMO
· To record DV input time cord and user’s bit from the IEEE1394 connector, set
the TC DUPLI. [DV] item on the TC/UB/CLOCK menu screen to ON. X See page 74.
· To maintain the continuity of time code data, use with the TC GENE. switch
set to REGEN mode when recording DV input signal from the IEEE1394 connector.
· There is no timecode display for HDV input.
CAUTION
A time code with a duration of more than 2 hours may not be displayed
correctly by DV components for general consumer use, as some of these lack the
capability to display longer time codes.
PREPARATIONS FOR OPERATION
Recording Time Codes in Continuation of Time Codes Recorded on Tape
The GY-HD100 also incorporates a time code reader. Therefore, when the unit
enters record mode from record-standby mode, it can read the time code data
recorded on the tape and record time codes in continuation of the existing
data. The recorded user’s bit data are identical to the user’s bit data
recorded on tape. * However, approximately ±1-frame variations may occur in
scene accuracy. To enable this function, set the time code related switches as
follows before starting recording.
Setting
Set the TC GENE. switch inside the LCD door to REGEN.
MEMO The time code framing mode automatically becomes the mode (drop frame or
non drop frame) already recorded on the tape.
Presetting and Recording of Time Code
TC/UB/CLOCK menu screen (FRAME RATE: 60/30)
The time codes from the internal time code generator can be recorded at the
time of recording scenes. · The TC/UB/CLOCK menu screen differs depending on
whether the FRAME RATE item on the VIDEO FORMAT menu screen is “60/30” or
“50/25”.
Framing mode: Drop frame/ Non-drop setting
TC/UB/CLOCK menu screen (FRAME RATE: 50/25)
To preset the Time Code, make the following settings.
TC GENE. switch Set to REC or FREE.
REC
: The data preset in the time code generator
runs only during recording. Use this setting if it is necessary to record
continual time codes across different scenes. * However, approximately ±1-frame varia-
FREE
tions may occur in scene accuracy. : The time code starts to run from the time
it is
preset in the time code generator.
TC/UB/CLOCK menu screen (FRAME RATE: 60/30) Use the DROP/NON DROP item to
select the framing
mode for the time code generator.
DROP
NON DROP
: The time code generator’s running method is set the drop frame mode. Use
this setting when placing emphasis on the recording time.
: The time code generator’s running method is set to the non drop frame mode.
Use this setting when placing emphasis on the number of frames.
MEMO
Drop frame/Non-drop frame mode In the NTSC system, the actual number of frames
per 1 second is approximately 29.97 frames, but per time code 30 frames are
processed. To compensate for this difference, the mode called “drop mode”
drops frame 00 and 01 for every minute not divisible by 10. The “non-drop
frame mode” is when no frames are dropped and the actual time shift neglected.
TC/UB/CLOCK menu screen (FRAME RATE: 50/25) Whether or not user’s bit data should be recorded can be selected with the UB REC item on the TC/UB/CLOCK menu screen.
38
39
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS FOR OPERATION
Presetting and Recording of Time Code (Cont’d)
Time code (hour, min, sec, frame)
Presetting time cord data
The time code and user’s bit data are preset on the TC/UB/ CLOCK menu screen.
1. Display the TC/UB/CLOCK menu screen.
Select the TC/UB/CLOCK item on the TOP MENU screen.
2. Set the time code (hours, minutes, seconds, frames).
1Rotate the SHUTTER dial to align the cursor (K) with TC PRESET, and then
press the SHUTTER dial. · The first digit of the time code blinks. The
blinking digit is the one to be set.
2When the SHUTTER dial is pressed, the blinking digit changes.
3When the SHUTTER dial is rotated, the value of the blinking digit changes.
When the SHUTTER dial is rotated upward, the value becomes higher. When
rotated downward, the value becomes smaller.
4Repeat the procedure described in 2 and 3 above to set the desired value for
all digits.
5After setting the frame digit, press the SHUTTER dial to make EXECUTE blink.
The setting values are confirmed when the SHUTTER dial is pressed again. To
cancel the setting, select CANCEL and press the SHUTTER dial.
3. When all the digits are set
· Press the STATUS button to return to the normal screen or
· Rotate the SHUTTER dial to align the cursor (K) with the PAGE BACK item, and
then press the SHUTTER dial to return to the TOP MENU screen.
Presetting user’s bit data
The user’s bit data are preset with the UB PRESET item on the TC/UB/CLOCK menu
screen. The method for setting is the same as the method for setting the time
code described above. · The user’s bit can be specified using numerals or
alpha-
betic letters from 0 to F for each digit. · To record user’s bit data, set the
UB REC item to ON.
CAUTION
It is not possible to set all the digits of the user’s bit data to “F”.
Reading of the data during playback will not be possible for an all-F setting.
Zero-resetting the Time Code or User’s Bit Data
This is performed with the TC or UB PRESET item on the TC/ UB/CLOCK menu
screen. (Performed separately for the time code and the user’s bit data.)
1Rotate the SHUTTER dial to align the cursor (K) with the
TC or UB PRESET item, and then press the SHUTTER dial. 2Rotate the SHUTTER
dial to select ZERO PRESET as the setting value, and then press the SHUTTER
dial.
MEMO
When a menu screen is not being displayed, you can zero reset the time code
data by simultaneously holding down the USER2 button and the STOP button for
about 1 second.
PREPARATIONS FOR OPERATION
Screen Adjustment
PEAKING volume LCD BRIGHT button
180° up
90° down
LCD lock release lever
Viewfinder Adjustment
Eyepiece focusing ring
Eyepiece
VF BRIGHT volume PEAKING volume Sliding securing ring
LCD monitor direction, angle, screen brightness, etc. can be adjusted.
Adjusting the Direction and Angle of the LCD monitor
· With the LCD door in the open condition, rotate the LCD door.
· It can be turned 180° in upward direction and 90° in downward direction.
When turned 180° upward direction, the LCD monitor can be viewed from the lens
side (vertically inverted image).
Adjusting the LCD monitor
· PEAKING: Adjusts the contour of the LCD monitor.
· LCD BRIGHT: Adjusts the brightness of the LCD monitor.
Adjustments are made on the LCD/VF [3/3] menu screen. X See page 73. · LCD
CONTRAST:
Adjusts the contrast of the LCD monitor.
Direction of the Viewfinder
Adjust the position and angle of the viewfinder.
Diopter Adjustment
Rotate the eyepiece focusing ring until the viewfinder screen image is clearly
visible.
Adjustment of the Viewfinder Screen
· PEAKING: Adjusts the contour of the LCD monitor and the viewfinder screen.
· VF BRIGHT: Adjusts the brightness of the viewfinder screen.
Adjustments are made on the LCD/VF [3/3] menu screen. X See page 73. · VF
CONTRAST:
Adjusts the contrast of the viewfinder screen.
Viewfinder mount base
MEMO
The screen size of the viewfinder can be changed by selecting the desired size
with the ASPECT item on the VIDEO FORMAT menu screen (4:3 or 16:9).
40
41
Downloaded from: https://www.usersmanualguide.com/
PREPARATIONS FOR OPERATION
Back Focus Adjustment
It is only necessary to perform this when the lens is attached for the first
time or when focusing is not correct in both the telephoto and wide-angle
positions.
· It is easier to adjust back focus when the subject is more than 3 meters
from the camera. The optimal subject for this adjustment is a Siemens star
chart.
1. Set the IRIS mode switch to M (Manual). 2. Set the zoom mode to M
(Manual). 3. Open the iris by turning the iris ring.
If the illumination is too strong, reduce it or move to a darker place.
4. Turn the zoom lever until the lens is at the maximum tele-
photo position.
5. Bring the subject into focus. 6. Set the lens to maximum wide-angle. 7.
Loosen the back focus ring retaining knob. 8. View the same subject and adjust
the back focus ring for
the best possible focus.
9. Repeat steps 4. through 8. about three times for fine
adjustment until the subject remains in focus in both the telephoto position
and the wide-angle position.
10.Tighten the back focus ring retaining knob to secure the
ring.
Siemens star chart
42
PREPARATIONS FOR OPERATION
White Balance Adjustment
Iris mode switch
ND filter
AWB button
WHT.BAL switch
POWER switch
During operation
Result message
Improper object
Insufficient illumination
Excessive illumination
CAUTION
· Do not adjust using any highly reflective objects, such as metal, etc., as
this may result in improper white balance adjustment.
· The FAW (Full Auto White balance) function cannot provide optimum white
balance with a subject outside the FAW adjustment range, for example when it
contains only a single color or not enough white color.
· The accuracy of the FAW (Full Auto White balance) is inferior to that of the
Auto white balance.
· When the power is turned on with the FAW mode selected, it takes about 10
seconds for the FAW adjustment to be completed. Do not shoot within this
interval.
Since the color of light (color temperature) varies depending on the light
source, it is necessary to re-adjust the white balance when the main light
source illuminating the subject changes.
White Balance Adjustment
Two kinds of white balance adjustment results can be stored in memories AUTO A
and AUTO B.
Adjustment procedure 1. Set the following switches.
· Set the POWER switch to ON. · Set the IRIS mode switch of the lens to A
(Auto). · Set the FULL AUTO switch to OFF.
2. Set the ND filter switch according to the current lighting. 3. Set the
WHT.BAL switch to A or B. 4. Place a white object near the center of the
screen under
the same lighting conditions as the target subject and zoom in to fill the
screen with white.
5. Press the AWB (Auto White Balance) button.
“AUTO WHITE A, B OPERATION” is displayed in the viewfinder while the auto
white balance adjustment circuit operates. When correct white balance is
obtained, the approximate color temperature is displayed together with “AUTO
WHITE A, B OK” for about 5 seconds.
Error messages
If the adjustment ends abnormally, an error message, as described below,
blinks for about 5 seconds. · NG: OBJECT (Improper object)
Displayed when there is not enough white color on an object or the color
temperature is not suitable. Replace the color temperature conversion filter
or use another white object and re-adjust the white balance. · ERROR: LOW
LIGHT (Insufficient illumination) Displayed when the illumination is dim.
Increase the illumination and then re-adjust the white balance. · ERROR: OVER
LIGHT (Excessive illumination) Displayed when the light is excessively bright.
Decrease the illumination and then re-adjust the white balance.
Full Auto White Balance (FAW)
The FAW function adjusts the white balance value automatically as the lighting
condition changes.
This mode is convenient when you have no time to adjust the white balance or
when the camera is moved frequently in and out of places under different
lighting conditions. Setting procedure
The FAW function can be activated with the FAW item on the SWITCH MODE menu
screen. The FAW function can be allocated to one of the white balance
switching switches A, B, or PRESET. X See page 69.
43
Downloaded from: https://www.usersmanualguide.com/
SETTING AND ADJUSTMENTS BEFORE SHOOTING
Setting the Video Format
SHUTTER dial
STATUS button
Set the video format using the FRAME RATE item and the REC item on the VIDEO
FORMAT menu screen.
Setting the FRAME RATE Item 1. Press the STATUS button for at least 1 second.
· The TOP MENU screen is displayed.
2. Turn the SHUTTER dial and bring the cursor (K) to the
VIDEO FORMAT.. item and press the SHUTTER dial. · The VIDEO FORMAT menu screen
is displayed.
3. Turn the SHUTTER dial and bring the cursor (K) to the
FRAME RATE item and press the SHUTTER dial. · The setting for the selected
item flashes and can be
changed. “CHANGE THE SYSTEM” is displayed on the screen.
4. Turn the SHUTTER dial, change the setting and push the
SHUTTER dial. · The setting stops flashing and is temporarily set. · Move the
cursor (K) to the EXECUTE item and EXE-
CUTE flashes.
5. Push the SHUTTER dial.
· “REBOOT! SYSTEM CHANGE” is displayed on the screen and after a few seconds
the system is rebooted.
Setting the REC Item
Set the REC item using the same steps as for the FRAME RATE item.
MEMO
· If you change the FRAME RATE item setting, the system is rebooted.
· The synchronous video signal is momentarily disturbed when the REC item
setting is switched.
About the Motion Smooth Function
When you set the MOTION SMOOTH item on the CAMERA PROCESS [2/2] menu screen to
ON with the REC item set to HDV-HD30P, HDV-HD25P or HDV-HD24P, the video can
be played back more smoothly than with normal progressive video. X See page
66.
SETTING AND ADJUSTMENTS BEFORE SHOOTING
Camera Settings
VTR indicator
4. 3. 1.
A B
1. Set the switch positions.
A. [GAIN] switch: Set to L ( 0 dB). B. [WHT. BAL] (Auto White Balance) switch:
Set to A or B.
2. Set the lens’ iris mode switch to “A” (Auto iris side). 3. Select the ND
filter.
ND FILTER OFF OFF
1 1/4ND 2 1/16ND
Suitable Location Indoors, dark outdoors Outdoors under clear sky Outdoors under extremely clear sky
4. Set the shutter speed to OFF with the SHUTTER dial.
CAM/VTR button
Screen Size (4:3/16:9) Mode Selection
ASPECT item 4:3
4:3 TV
The screen size of recorded images can be selected with the ASPECT item on the VIDEO FORMAT menu screen. X See page 62. · To record using the standard screen, set ASPECT to 4:3. · To record using the 16:9 screen, set ASPECT to 16:9.
16:9 TV
16:9
4:3 TV
16:9 TV
MEMO
· When you set the REC item on the VIDEO FORMAT menu to HDV format, the ASPECT
item is fixed at 16:9 and “[16:9]” is displayed.
· In the SAFETY ZONE item on the LCD/VF [1/3] menu screen, you can display the
safety zone for a standard screen as well as a 16:9 screen in the viewfinder
or LCD monitor. X See page 71.
· When the ASPECT item is set to 4:3, the screen that is displayed may differ
depending on the 16:9 television you are using.
44
45
Downloaded from: https://www.usersmanualguide.com/
SETTING AND ADJUSTMENTS BEFORE SHOOTING
Audio Input Signal Selection
CH-2 INPUT switch
AUDIO INPUT switch
MONITOR SELECT FULL AUTO switch switch
MONITOR volume
Monitor speaker
CH-1 audio input level volume
CH-2 audio input level volume
CH-1/CH-2 AUDIO SELECT switch
STATUS 1 screen
Audio level Indicator level (reference)
f
The GY-HD100 is provided with the INPUT1 connector and the INPUT2 connector for audio input. Select the audio from the INPUT1 connector or the INPUT2 connector using the CH-2 INPUT switch for the audio to be recorded in CH-2.
Selecting the CH-2 channel input connector
Select using the CH-2 INPUT switch.
INPUT1
: Inputs the audio from the INPUT1 connector into CH-2.
INPUT2
: Inputs the audio from the INPUT2 connector into CH-2.
MEMO
The audio from the INPUT1 connector is also input into CH1 regardless of the
setting.
Selecting the audio signal input
Select the sound to be input to the INPUT1 or INPUT2 con-
nector using the AUDIO INPUT switch.
The setting is made for each of INPUT1 or INPUT2 connec-
tor.
LINE
: Set to this position when connected to audio
equipment, etc.
The reference input level is +4 dBs.
MIC
: Set to this position when using a dynamic micro-
phone.
MIC+48V : Set to this position when a microphone (phan-
tom microphone) requiring +48 V DC power sup-
ply is connected.
CAUTION When connecting a component that does not require +48 V power supply,
make sure that the switch is not set to MIC+48V before the component is
connected.
MEMO You can select the normal input level for MIC and MIC+48V in the INPUT1,
2 MIC REF. item on the AUDIO/MIC menu screen.
Adjusting Audio during Recording
For each audio channel, use the CH-1/CH-2 AUDIO SELECT switch to select
whether the audio level adjustment should be set to AUTO mode or MANUAL mode.
Adjusting the audio input level control The audio input level can be adjusted
manually when the GYHD100 is in the record, record-standby or stop mode.
1. Set the CH-1/CH-2 AUDIO SELECT switch of the channel
whose audio level that you want to adjust manually to MANUAL.
2. Rotate the audio input level control corresponding to the
audio input level to be adjusted. · Adjust so that the peak level does not
exceed the 3 dB
point when a loud sound is input.
46
PHONES jack
SETTING AND ADJUSTMENTS BEFORE SHOOTING
CAUTION
· When the AUDIO INPUT switch is set to MIC, be sure to check that the
microphone is connected to the INPUT1/2 connector. If the microphone is not
connected, increasing the audio level could cause noise from the input
connector to be recorded on the tape. When the microphone is not connected to
the INPUT1/2 connector, set the AUDIO INPUT switch to “LINE” or turn down the
audio level control.
· In the FULL AUTO mode, the audio level volume cannot be adjusted with the
audio level controls on the CH-1 and CH-2.
MEMO
The reference level for audio recorded on the tape can be set with the AUDIO
REF. LEVEL item on the AUDIO/MIC menu screen. (20 dB or 12 dB) The level
will change for both CH-1 and CH-2.
Monitoring Audio during Recording
The audio input during recording, in record-pause or stop
mode can be monitored through the monitoring speaker or earphone.
· Select the audio channel to be monitored using the MONITOR SELECT switch.
CH-1 BOTH
CH-2
: The sound input to the CH-1 channel is output. : The sound input to the CH-1
and CH-2 channels
is output mixed. : The sound input to the CH-2 channel is output.
· The MONITOR volume control adjusts the monitoring volume.
· The loudspeaker or earphone outputs an alarm tone in the case of an abnormal
condition occurring in the unit. An alarm tone is also output when the tape
end is reached or when the battery is running down. * Do not increase the
audio monitoring volume excessively; otherwise howling with the camera
microphone may occur.
MEMO
· When connecting a stereotype earphone, make the following settings to output
stereo sound. 1Set the MONITOR SELECT switch to BOTH. 2Set the AUDIO MONITOR
item on the AUDIO/MIC menu screen to STEREO.
· When AUDIO MONITOR item on the AUDIO/MIC menu screen is set to “STEREO”,
only the audio of CH-1 is output from the monitoring speaker.
· The volume of the alarm tone is set with the ALARM VR LEVEL item on the
OTHERS [1/2] menu screen. (OFF/ LOW/MIDDLE/HIGH)
47
Downloaded from: https://www.usersmanualguide.com/
SHOOTING OPERATION
Basic Recording Operation
FRONT TALLY lamp
1. Set the POWER switch to ON.
· The unit turns on in camera mode.
2. Start recording.
Press the REC/VTR trigger button on the GY-HD100 to start recording. Once
recording has started, the FRONT TALLY lamp and BACK TALLY lamp light red.
MEMO
The way the FRONT TALLY and the BACK TALLY lamps flash differ depending on
what you set in the FRONT TALLY and BACK TALLY items on the OTHERS [1/2] menu
screen. X See page 77.
POWER switch REC trigger button
BACK TALLY lamp
FOCUS ASSIST button
RET button
CAUTION
· The unit enters the stop mode automatically at TAPE END. If this mode
continues for 3 minutes, the mode switches to the tape protect mode. X See
“OTHERS [1/2] Menu Screen” on page 77. (LONG PAUSE TIME item)
· If the REC/VTR trigger button is pressed very quickly and repeatedly, or the
POWER switch is moved immediately after the trigger button is pressed, the GY-
HD100 may not enter the record mode. To remedy this condition set the POWER
switch to OFF and wait for 5 seconds or more before turning the power on
again.
· A neat transition to the next recorded scene cannot be guaranteed if a
recording is ended by turning the POWER switch or DC power supply OFF, or by
removing the battery pack.
· Trial-shooting is always recommended before recording important events to
confirm the recording is satisfactory.
· The microphone may pick up the sound of the lens’ iris if the iris is
changed abruptly or the iris is manually moved abruptly during recording.
VTR trigger button
About the QUICK REC START Mode If the REC/VTR trigger button is pressed
immediately after the videocassette is inserted, the mode becomes the QUICK
REC START mode that enables quick start of recording. However, when shooting
starts in the middle of the tape, a blank space appears as the new scene will
not be linked smoothly with the previous image. Also, the time code does not
continue. (Some overlap may also occur.)
About the Focus Assist Function
When you press this button during shooting, the area of focus is displayed in
blue, red or green, making it easy to focus accurately. X See “LCD/VF [1/3]
Menu Screen” on page 71. You can also set this function from the RET button. X
See “SWITCH MODE Menu Screen” on page 69. (LENS RET item)
48
SHOOTING OPERATION
VTR mode indication
1. RET button
If the Record-Standby Mode Continues
Setting the time before the tape protection mode is engaged The time before
the tape protection mode is engaged from the record-standby mode can be set to
5 minutes or 3 minutes with the LONG PAUSE TIME item on the OTHERS [1/2]
screen menu. X See page 77. When the record-standby mode has continued for
about 5 minutes or 3 minutes, the GY-HD100 automatically stops drum rotation
in order to protect the tape. (Tape protect mode)
In the tape protect mode, STOP is shown as the VTR mode indication on the LCD
monitor and in the viewfinder screen. (STATUS 1 screen) To start recording
from the tape protect mode, press the REC/VTR trigger button. · The drum
starts rotating, and recording starts after about
3 seconds. To return to the record-standby mode from the tape protect
mode, press the RET button. CAUTION This function does not work when using RET
button is used as FOCUS ASSIST button.
Checking Recorded Contents in RecordStandby Mode (Recording Check Function)
This function is available only when the GY-HD100 is in the standby mode. In
standby mode, about 5 seconds of the last part of the content recorded in DV
format can be played back, and about 7 seconds when the content was recorded
in HDV format can be played back. · The recorded contents can be checked on
the LCD moni-
tor, in the viewfinder or on a monitor connected to the video signal output
connectors. · The video image from the VTR section is shown on the LCD
monitor, in the viewfinder or on the monitor connected to the video signal
output connectors.
1. In the record-standby mode, press the RET button on the
camera lens section. · The tape rewinds and about 6 seconds of the content
recorded in DV format is played back, and about 8 seconds of the content
recorded in HDV format is played back. After playback, the camcorder returns
to standby mode at the position on the tape where the RET button was pressed.
If you continue to hold down the RET button, up to about 18 seconds of content
recorded in DV format and up to about 20 seconds of content recorded in HDV
format can be rewound and played back. · Pressing the REC/VTR trigger button
during playback will put the unit in REC standby mode. The camera will
automatically return to recording mode after playback.
CAUTION
· This function does not work when using RET button is used as FOCUS ASSIST
button.
· This function does not work when the GY-HD100 is in the stop mode.
· During recording check, the following indication will appear if the error
rate increases due to head clogging, etc. “HEAD CLEANING REQUIRED!” is shown
on the LCD monitor or in the viewfinder. (When the STATUS 0, 1, 4 screen is
displayed.)
49
Downloaded from: https://www.usersmanualguide.com/
SHOOTING OPERATION
HEADER REC Function
When the REC/VTR trigger button is pressed while the STOP button is pressed,
this function first records the color bar video and the test tone (1 kHz sine-
wave) of the built-in signal generator at the beginning of the tape. Then it
records the black video signal and the mute audio signal for the duration
specified in advance. When the recording is completed, the unit enters the
RecordStandby mode. The time code value at the Record-Standby position becomes
the time code specified in advance. (HEADER REC function) · Settings related
to the HEADER REC function, such as whether the HEADER REC function should be
enabled, the HEADER
REC execution duration, and the time code value setting when the HEADER REC
recording is completed, etc., are made on the HEADER REC menu screen. · The
HEADER REC function is executed under the following circumstances: CAM/VTR
button: Set to CAM mode. In the Record-Standby or Stop mode
Tape beginning
HEADER REC (Example) 30 sec
Record-Standby mode
(Example) 30 sec
Normal recording
Color bar video signal Test tone (1 kHz) (Setting range: 0 to 99 sec)
Time code, user’s bits recording
Black video signal Mute audio (No sound) (Setting range: 0 to 99 sec)
Time code, user’s bits recording
Time code: The value specified on the HEADER REC menu screen- HEADER REC time (Example) 23:59:
References
- JVC Europe
- User Manual, users guide, operation instruction
- User Manual, users guide, operation instruction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>