VirtualFly TRIMSneo Virtual Fly Switch Trim Panel User Guide
- June 14, 2024
- VirtualFly
Table of Contents
VirtualFly TRIMS neo Virtual Fly Switch Trim Panel User Guide
TRIMS neo
Guick Start Guide
Rev. 1.0 – July 2023
IN THE BOX
A) TRIMSneo
B) Clamp
C) Allen keys (n.2.5, n.3)
D) Adapter to Attach TQneo/ TQ6/ V3RNIO
E) USB-A to USB-B Cable
F) Allen Screws DIN 912 M4
G) Allen Screws DIN 7991 M4
G) Power Supply
H) Rubber Feet
For support, contact us at support@virtual-fly.com
© 2023 Virtual Fly, SL
All trademarks and brand names are trademarks or registered trademarks of
their respective owners. All rights reserved.
C. Maria Aurèlia Capmany, 21
P.I. La Fàbrica – 08297 Castellgalí (Spain)
Phone: (+34) 938 333 301
https://www.virtual-fly.com
HARDWARE SETUP
ATTACHING TO DESKTOP/HOME COCKPIT
SETUP
Attach the TRIMSneo using the included clamp (B) and allen screws (C). Manually unscrew the TRIMSneo rubber feet (H) and place the TRIMSneo on the surface it will rest and tighten the knob (a) until you feel strong resistance.
ATTACHING TQneo/ TQ6/ V3RNIO to TRIMSneo
If you own a TQneo, TQ6 or V3RNIO product, you can attach it to the TRIMSneo using the provided Adapter (D) as follows:
-
Detach the Adapter (D) from the TRIMSneo by pressing the pin-button (b) indicated below, and slide it to the right and up to extract it.
-
Unscrew the TQ’s rubber feet (if applicable), align the holes from the Adapter and TQ and attach the TQ into the Adapter with the screws provided with it as shown below.
-
Insert the Assembly’s guides on the TRIMSneo‘s slots as indicated below.
-
Slide the Assembly all the way until the end.
-
Secure it by pressing the pin-button again.
CONNECTING TO PC
Connect the power supply (G) to the back of the TRIMSneo and plug it to the power source. Connect the USB cable (E) to the back of the TRIMSneo and the computer where the flight simulator software is running.
SOFTWARE SETUP
The TRIMSneo interacts with any computer being compatible with any flight simulation software through VFHub, the software developed by Virtual Fly to simplify setting up our products.
To use TRIMSneo, there is only one way to configure it and that is through the VFHub. With VFHub, you can fly your favorite software without worrying about configuring your Virtual Fly flight controls.
You can download the latest VFHub version from this link: https://www .virtual-fly.com/setup-support. The VFHub installer takes care of installing VFHub and all the required modules. VFHub is compatible with MSFS, Prepar3DV4-V5 and X-Plane 11/12.
After installing VFHub, make sure your TRIMSneo is connected to your computer. Run VFHub, and verify that the TRIMSneo status displayed in the Dashboard is “Connected”
VFHub takes care of making your TRIMSneo work with MSFS, Prepar3DV4-V5 and X-Plane 11/12, so it must always be running when you use the TRIMSneo.
References
- Cheap Flights: Flights Tickets, Airline Tickets, Search Flights | Fly.com us
- Virtual Fly | Professional Flight Simulators and Controls
- Virtual Fly | Professional Flight Simulators and Controls
- Flight Simulation Setup & Support | Virtual Fly
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>