Panasonic F-56MZG Ceiling Fan Instruction Manual

Panasonic F-56MZG Ceiling Fan

Product Information

The product is a Ceiling Fan designed to provide air circulation and cooling in a room. It is important to follow the safety precautions and instructions provided in the user manual to avoid injury to users or damage to properties. The Ceiling Fan should be installed properly by a qualified individual to prevent any mishaps.

Product Usage Instructions

• Installation: Follow strictly all the instructions given in the manual for installation. Electrical or installation work needs to be performed by a qualified individual.  Installation errors can cause fire, electrical shock, injury, orthe Ceiling Fan to drop. Ensure that the Ceiling Hook can sustain  more than 10 times the Ceiling Fan weight.
• Cleaning and Maintenance: Switch off the power supply and wait until the Blades are fully static before cleaning or doing any maintenance jobs. This prevents the possibility of  injury or electrical shock if the Ceiling Fan moves suddenly.Kindly refer to your authorized dealer for repairing or maintenance.
• Abnormality or Failure: If any abnormality or failure occurs, stop using the Ceiling Fan and turn OFF the Miniature Circuit Breaker (MCB). There is a risk of smoke, fire, electrical shock, and drop. Please contact your authorized dealer for maintenance/repair.
• Dismantling: If the Ceiling Fan is broken or damaged, dismantle it carefully to avoid injury in case the Ceiling Fan drops.
• Oscillating Movement: If unusual oscillating movement is observed, immediately stop using the Ceiling Fan and contact the manufacturer, its service agent, or suitably qualified persons. This can cause injury if the Ceiling Fan drops.
• Installation Location: Do not install the Ceiling Fan at oily and dusty places, near flammable areas such as a gas cooker, near chemicals and alkaline substances. This can cause fire, explosion, short circuit, and electrical shock.
• Wire Handling: Do not damage the wire during installation (e.g., deform due to heat, twist, bend, etc.). This can cause fire, explosion, short circuit, and electrical shock.
• Power Supply: Use only the rated voltage mentioned. Using a different power supply can cause overheating, electrical shock, or fire.
• Battery Area: Do not insert any metal items in the battery area. This can cause fire, explosion, short circuit, and electrical shock.
• Hanging onto the Ceiling Fan: Do not hang onto the Ceiling Fan as it can cause injury if the Ceiling Fan drops.
• Disassembling: Do not disassemble the Ceiling Fan unless stated by the manual. Use only the supplied parts to avoid fire, electrical shock, injury, or the Ceiling Fan from dropping.
• Operating: Do not touch the Ceiling Fan while it is operating as it can cause injury, damage, or the Ceiling Fan to drop.
• Water Contact: Do not sprinkle water on the  Ceiling Fan or wet it. This can cause fire, explosion, shortcircuit, and electrical shock.

Note: Always follow these instructions to avoid the possibility of causing injury to users or damage to properties. The manufacturer will not be responsible for any accidents or injuries caused by defective or deficient installation or installation that does not follow the instruction manual.

Safety precautions

To avoid the possibility of causing injury to users or damage to properties, please follow all the explanations written below.
This symbol denotes an action that is COMPULSORY.
This symbol denotes an action that is PROHIBITED.
WARNING
A state that may be caused by the mishandling of products, which, if not avoided, may lead to the possibility of death or serious injury of users.
CAUTION
A state that may be caused by the mishandling of products, which, if not avoided, may result in the injury of users or property damage.
WARNING

• Follow strictly all the instructions given in this manual for installation. Electrical or installation work needs to be performed by a qualified individual. Installation error can cause fire, electrical shock, injury or Ceiling Fan to drop.

• Switch off the power supply and wait until the Blades is fully static, before cleaning or doing any maintenance jobs. Can cause injury or electrical shock if Ceiling Fan move suddenly.

• Kindly refer to your authorized dealer for repairing or maintenance.

• Ensure that the Pipe has been fully tighten to Motor Shaft (Bolt tightening torque is 800~1200 N•cm) and Cotter Pin must fix into Bolt and bent.
  Can cause injury if Ceiling Fan drops.

• Tighten the Blade Screws firmly using a screwdriver. (250-300 N•cm)
  Can cause injury if Blade drops.

• Ensure that the Ceiling Hook can sustain more than 10 times the Ceiling Fan weight. Can cause injury if Ceiling Fan drops.

• Stop using the Ceiling Fan when any abnormality or failure occurs and turn “OFF” the Miniature Circuit Breaker (MCB). Risk of smoke, fire, electrical shock and drop. Please contact your authorized dealer for maintenance/repair.

• Dismantle the broken or damaged Ceiling Fan.
  Can cause injury if Ceiling Fan drops.

• If unusual oscillating movement is observed, immediately stop using the Ceiling Fan and contact the manufacturer, its service agent or suitably qualified persons.
  Can cause injury if Ceiling Fan drops.

• Do not install the Ceiling Fan at oily and dusty places.
  Can cause fire, explosion, short circuit and electrical shock.

• Do not install the Ceiling Fan near flammable areas such as a gas cooker. Can cause fire, explosion, short circuit and electrical shock.

• Do not install the Ceiling Fan near chemicals and alkaline.
  Can cause fire, explosion, short circuit and electrical shock.

• Do not damage the wire during installation e.g. deform due to heat, twist, bend, etc. Can cause fire, explosion, short circuit and electrical shock.

• Do not use power supply other than rated voltage mentioned
  Overheating can cause electrical shock or fire.

• Do not insert any metal items in the battery area with the Battery.
  Can cause fire, explosion, short circuit and electrical shock.

• Do not hang onto the Ceiling Fan. Can cause injury if Ceiling Fan drops.

• Do not disassemble the Ceiling Fan unless stated by this manual.
  Must use only supplied parts.
  Can cause fire, electrical shock, injury or Ceiling Fan to drop.

• Do not touch the Ceiling Fan while it is operating.
  Can cause injury, damage or Ceiling Fan to drop.

• Do not sprinkle water to Ceiling Fan or do not wet the Ceiling Fan.
  Can cause fire, explosion, short circuit and electrical shock.

CAUTION

• To avoid the possibility of causing injury to users or damage to properties, please follow all the explanation written in this manual. The manufacturer will not be responsible for any accidents or injuries caused by defective, deficient installation or installation which does not follow the instruction manual. Can cause the injury of users or property damage.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  Children should be supervised to ensure that they do not play with the appliance. Can cause the injury of users or property damage.

• The Ceiling Fan must be mounted above 2.3 m from the floor and 1 m from the wall to the Blade.
  Can cause unstable air flow and affect Ceiling Fan to wobble.
  Can cause injury if Ceiling Fan drops. Refer to page 12 (step 4) for the measurement method.

• After installation make sure the Ceiling Fan does not wobble extremely.
  Can cause injury if Ceiling Fan drops.

• Replace all the Blades if any of them breaks or cracks.
  Can cause injury if Ceiling Fan drops.

• The mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualifed persons.
  Can cause injury if Ceiling Fan drops.
  The Ceiling Fan suspension system should be examined at least once every two years.
  Can cause the injury of users or property damage.

• The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.
  Can cause the injury of users or property damage.

• This product is for in house use only. Do not install at a windy places. Can cause injury if Ceiling Fan drops.

• Do not install at places where there is high vibration and impact.
  Can cause injury if Ceiling Fan drops.

• Avoid fixing inside dome ceiling. Can cause unstable air flow and affect Ceiling Fan to wobble.
  Can cause injury if Ceiling Fan drops.

• Wipe away dirt with a clean soft cloth, ordinary soap and water to keep the Ceiling Fan clean. Do not use solvents (gasoline and petroleum) or any other chemicals.
  Can cause plastic part deformation or metal corrosion.
  Can cause injury if parts drop.

• Do not install the Ceiling Fan at a wet, high temperature and high humidity area such as shower room.
  If an electrical current leakage occurs, it can cause electrical shock or fire easily.

Maintenance

1. Check the Ceiling Fan condition annually. If a problem occurs, stop using the Ceiling Fan. Refer to a service, sales or maintenance shop.
   Check point:
   Loosened screws, safety wire condition, motor shaft damage, etc.

2. Ensure Safety Switch in good condition.

3. If a problem occurs, stop using the Ceiling Fan. Refer to a service, sales or maintenance shop. Keep the Ceiling Fan clean. Wipe with a clean soft cloth, ordinary soap and water. Wipe it again to dry it. Do not use solvents (gasoline/ petroleum).

   • Hold the Blade tip during cleaning process to avoid bending the Blade.
   • Do not bend the Blade while cleaning.

4. Do not paint the Blades. If damaged, order a new set of parts from a service, sales or maintenance shop.

5. When referring to a service, sales or maintenance shop, show these operating instructions to them and maintain correctly. If the product is broken or damaged, remove it from the ceiling and replace with new one. This is to avoid Ceiling Fan drops. The

6. Ceiling Fan suspension system should be examined at least once every two years.

Name of parts

• A Upper Canopy            1
• B Pipe (9 or 16 inch)      1
• C Lower Canopy                 2
• D Motor Assembly             1
• E Blade Assembly Set        4
• F Pulley Set                1
• G Ellipse Bolt             1
• H P-R Washer           1
• I Spring Washer         1
• J Hexa Nut                 1
• K Cotter Pin                1
• L Batteries                      1
• M Remote Control             1
• N Remote Control Holder Set          1

Attention:

• Do not place the Ceiling Fan directly on the floor. Can cause scratches to the product.
  Note:

• The illustrations in this manual are for explanation purposes only and may differ from the actual unit.

How to install

Insert the Canopy

1. Pull out the Safety Wire from Pipe as shown.
   Remove Safety Wire Screw and remove Lower Canopy Screws from Pipe .
   Keep these screws for page 13 step 4- and page 16 step 6- .

2. Insert the Upper Canopy to the Pipe
   Do not screw the Upper Canopy Screw Check point after installation
   Insert the Upper Canopy to Pipe Assembly and the screw is not tightened.

Assemble the Motor Assembly to the Pipe

1. Pull the Power Cord (from the power supply) and insert into the Pipe hole as shown.

2. Assemble the Motor Assembly to the Pipe that hang on Ceiling.
   Fix the Pipe to Motor Shaft as shown. Ensure the Switch Lever press the Switch . Ensure that the Pipe hole and the Motor Shaft hole are aligned. CAUTION
   Do not remove the Switch Lever at Pipe. Fix the Pipe correctly to the Motor Shaft. Can cause injury if the Ceiling Fan drops.

3. Fix the Pipe and the Motor Assembly with the Ellipse Bolt , the P-R Washers , the Spring Washer , the Hexa Nut and the Cotter Pin . The Slit of the Ellipse Bolt should be at top and bottom. Bend the Cotter Pin at last as shown. WARNING
   Ensure that the Pipe is fully tightened to the Motor Shaft. (Bolt tightening torque is 800-1200 N•cm). And the Cotter Pin must be inserted into the Ellipse Bolt hole and bent.
   Can cause injury if the Ceiling Fan drops.

4. Remove the Safety Wire Screw at the Motor Shaft . Fix the Safety Wire firmly to the Motor Shaft with Safety Wire Screw .
   Tighten the Safety Wire Screw . WARNING
   The Safety Wire must be fixed correctly and connected at all times.
   Can cause injury if the Ceiling Fan drops. Ensure that the angle (a) keeps 40-45 degree and the Safety Wire does not touch the motor surface.

5. Connect the Power Cord to the 3 pin Terminal WARNING
   Make sure all the terminals are connected correctly by a competent person to avoid electrical hazards.
   Make sure all the wires must be fully insert and the 3 pin terminal screw is fi rmly tightened. Can cause fire, electrical shock.
   Check point after installation
   Switch Lever press the Switch.
   The Ellipse Bolt, the P-R Washers, the Spring Washer and the Hexa Nut are fi rmly tightened, and the Cotter Pin is inserted and bent for safety reason.
   The Safety Wire Screw is firmly tightened.
   All wires are connected correctly by a competent personnel.

Assemble the Blade Assembly Set to the Motor Assembly

1. Remove the Blade Screws (8 pieces, silver colour) from the Motor Assembly .

2. Assemble the Blade towards the Motor Assembly .

3. Tighten the Blade Screws (Silver colour) firmly. Use 2 screws for one Blade.
   For reference, tightening torque is 250-300 N•cm. Attention:

   • Ensure that the Blade is fixed correctly.
   • Ensure the Safety Plate is fixed correctly at the Blade frame.
     Do not install the Blade without Safety Plate.

Install to the ceiling

1. Take out the Pulley Set from the parts set.
2. Cross the C Hook of the Pulley Set to the  Pipe , inclining the C Hook and aligning  it parallel with the Pipe hole.
3. Place the Pulley onto the Ceiling Hook .

Note:

1. Step can be done before step .

2. Make sure that the Ceiling Fan maintain a straight position during installation to avoid the Blade from touch the wall or ceiling.

3. In case “U” Hook is being used, installation method is the same.
   WARNING
   Ensure that the Ceiling Hook can sustain more than 10 times the Ceiling Fan weight.
   Can cause injury if the Ceiling Fan drops.
   Product weight approximately 6.9 k?.
   CAUTION
   Ensure that the Ceiling Fan is not tilted so that the Blade does not touch the wall during installation. Can cause injury if the Ceiling Fan drops.

4. Loop the Safety Wire to the Ceiling Hook and fix it to the Pipe with the Screw removed in page 8 step 1- . CAUTION
   The Safety Wire must be fixed correctly.
   Can cause injury if the Ceiling Fan drops.
   Check point after installation
   The Safety Wire is looped to the Ceiling Hook and securely fixed to the Pipe.

Wiring instruction

Connect to the power supply according to the wiring Instruction below.
Wiring diagram Connecting to the power supply
Attention

• This product should be installed with a double pole single throw switch (breaker switch) with a minimum 3 mm contact gap in the fixed installation circuit.

• If your Remote Control missing or misplaced, the Ceiling Fan can be switched on pre set speed 2.

• Do not use regulator or dimmer switch for this model.
  (It can damage the Ceiling Fan)

• Should there be a regulator or dimmer switch, disconnect it and reconnect the wiring as above.

• It is recommended to replace regulator point or dimmer switch with OFF/ON switch on the wall.

WARNING
Electrical wiring must be done by a qualified individual.
Can cause fire, electrical shock.
This product is not provided with a cord and plug or with other means for connection to the supply.
When connecting or changing the power cord or lead wire, it must be performed by a qualified person in order to avoid a hazard. Please use 227IEC53(RVV) or thickness of tube 1 mm or above. (If there are other requirements such as the diameter of lead wire, please use according to the regulation of the country).
Can cause fire, electrical shock.
Do not bypass and short circuit the Safety Switch.
Can cause fire, electrical shock, injury or Ceiling Fan to drop.
Check point after installation
The wiring is connected properly to the power supply.

Fix the Canopy

1. Adjust the position of Upper Canopy and fix it to the Pipe tightening the Screw firmly
   The distance between the Upper Canopy and the ceiling is > 5 mm.

2. Fix Lower Canopy . Using Lower Canopy Screw which was removed from Pipe at page 8 step 1- .
   Fix Lower Canopy B to Pipe by using Lower Canopy Screw .

3. Fix Lower Canopy A to Lower Canopy B by sliding it down as shown.

4. Fix Lower Canopy A to Pipe by using Lower Canopy Screw . CAUTION
   Lower Canopy A and B must be fixed correctly.
   Can cause injury if Lower Canopy drops.

Final confirmation
Measure the distance using a measuring tape. Adjust all the Blades to get an equal distance from the ceiling to the tip of the Blade
(Within 1 mm tolerance).
Pitching method
Hold the Blade frame by hand and adjust the distance (L) by pushing up or pressing down the Blades gently until the difference of distance (L) should be ± 1 mm. CAUTION
After installation, make sure that the Ceiling Fan does not tremble extremely. Can cause injury if the Ceiling Fan drops.
Do not overbend the Blade when pitching.
Can cause injury if the Ceiling Fan drops.
Install Remote Control Holder
Install the Remote Control Holder Set to wall. Fix the Remote Control Holder using provided Screw (2 pieces) and Wall Plugs (2 pieces) as shown in figure below.

• Distance between holes is 20 mm.
• Depth for Wall Plug is 30 mm.

How to use

Before use

1. Remove the cover of Remote Control .

   • Pull the Flap to remove.

2. Insert the Batteries
   (2 pieces AA / R6P / R6 / LR6).

   • “+” “-” position should match.

3. Close the cover.

   • Insert the protruding part (2 positions) into the Remote Control (2 holes), and press the Flap .

Attention:

1. Please remove all Batteries before disposing the Remote Control. The life of Battery is about one year for a normal usage.
2. Replace all Batteries at one time and be careful not to mix Battery type.

Remote Control coverage

1. The figure above shows the best coverage area (W) around 8 m if the height (H) is 4 m. The Remote Control must be pointed to the direction of the Ceiling Fan when in use.
2. Avoid the following situations :
   • Netting and Glass can reduce the signal power or reflect the infrared signal from the Remote Control.
   • Lighting effect generated by Fluorescent Lighting Systems directly onto the product receiver area can affect the signal transmission.
   • Obstacles such as Walls or Glass between the product receiver and Remote Control can cause signal transmission failure.

Attention:

• The power consumption when the operation is turned off by Remote Control is about 1 W.
• It is recommended to switch off wall switch or breaker if Ceiling Fan is not in use for long period. This is for zero power consumption purpose.

How to use Remote Control

1. OFF/ON Button

   • Press OFF/ON button to switch ON or OFF the Ceiling Fan.
     “ON” – Short beeping sound.
     “OFF” – Long beeping sound.

2. Speed Button

   • 3 speed control (SPEED 1, 2, 3).

3. OFF TIMER

   • If 6 hours timer is ON (3 lights indication), the timer will gradually count down from 6 hours (6h) to 3 hours (3) (2 lights indication), then 1 hour (1) (1 light indication) until OFF (no light indication).

4. Timer Cancel

   • Push this button to cancel SLEEP MODE or OFF TIMER.

5. SLEEP MODE

   • Step 1: Select SPEED 2 or 3.
   • Step 2: Select (3) or (6h) timer.
   • Step 3: Press SLEEP MODE button and timer light indication at Ceiling Fan will blink. For SLEEP MODE function, refer SLEEP MODE FUNCTION chart. To cancel, press once more.

How to use OFF TIMER
Press the desired button to set the timer as shown above.

• Indicating lamp at the Ceiling Fan will change accordingly as remaining time reduces.
• Press the CANCEL button to stop using timer function.

How to use SLEEP MODE
Press the SLEEP MODE button.

• Indicating lamp at the Ceiling Fan will blink according to remaining time.
• Press again the SLEEP MODE button to cancel.
  Refer SLEEP MODE FUNCTION chart below. Timer| 6h| 5h| 4h| 3h| 2h| 1h| 0h
  ---|---|---|---|---|---|---|---
  Speed 3| 3| | 2| | 1| | OFF / TẮT
  | | | 3| | 2
  Speed 2| 2| | 1| | |
  | | | 2| | 1

Note:

• Ceiling Fan speed and timer will gradually go down until the Ceiling Fan is OFF.
• SLEEP MODE function is disabled at Speed 1 and 1 hour setting.

Specifications

Panasonic Corporation
Web site: https://holdings.panasonic/global
© Panasonic Ecology System Co., Ltd 2020-2023

References

• Panasonic Holdings Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>