FLASH F7200226 2x150W DualBlaze Light User Manual

SERIES: DJ

F7200226 2x150W DualBlaze Light

DualBlaze 2x150W
User Manual

WARNING! Use clamp to rig the fixture.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the bar so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 1. The DualBlaze lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the DualBlaze, as intense illumination can damaged the display.

INTRODUCTION

THANK YOU FOR PURCHASING DUALBLAZE. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

• Please keep this User Manualfor future consultation. If you sellthe fixture to another user, be surethat they also receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the fixture.
• Before operating, ensure thatthe voltage and frequency of power supply match the powerrequirements of the fixture.
• It’s important to ground theyellow/green conductor to earthin order to avoid electric shock.
• Disconnect main power beforeservicing and maintenance.
• Use safety chain when fixes this fixture. Don’t handle the fixture bytaking its head only, but always bytaking its base.
• Maximum ambient temperatureis: 40°C Don’t operate it where thetemperature is higher than this.
• In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself.
• Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
• Do not connect the device to any dimmer pack.
• Do not touch any wire during operation and there might be a hazard of electric shock.
• To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
• The housing must be replaced if they are visibly damaged.
• Do not look directly at the li- ght spot while the fixture is on.

PRODUCT INFORMATION

• Light Source: 2x 150W LED 1800-5600K
• Power consumption: 300W
• Power supply voltage: 90-240V, 50/60Hz AC
• Operating modes: DMX512, Manual, Auto, Sound-controlled, Master/Slave,
• DMX channel mode 4 C H / C H 8 A / C H 8 B
• IP Rating: IP20
• Housing made: Steel + ABS
• Cooling: Active
• AC IN/OUT: powerCON
• 3-Pin XLR DMX Input/Output
• Net Weight: 3,2 kg
• Net Dimensions:
• H(23)xW(37)xD(13,5) cm
• Pack Size: H(25)xW(40)xD(21) cm

INSTALATION

The unit should be mounted viaits screw holes on the bracket.Always ensure that the unit isfirmly fixed to avoid vibrationand slipping while operating.Always ensure that the structure to which you are attachingthe unit is secure and is ableto support a weight of 10 times of the unit’s weight. Alsoalways use a safety cable thatcan hold 12 times of the weight of the unit when installingthe fixture. The equipment mustbe fixed by professionals. And itmust be fixed at a place where isout of the touch of people andhas no one pass by or under it.The fixture may be installed inany orientation, but if installedhorizontally with a downward beam-angle, water can potentially pool in the fan wells. Under normal operation the moisture will evaporate. However, in locations with high rainfall, you may wish to fabricate a rain shield above the fixture, or modify the position and orientation of the fixture to minimize pooling. Two quarter-turn brackets are supplied with the fixtre if it is to be flown above the ground. Rig the fixture to a support truss or structure using the supplied brackets and suitable clamps. Fasten a safety cable between the support structure and the attachment point on the fixture. The safety cable must be able to bear at least 10 times the weight of the fixture.

The package includes:

❶ – DualBlaze (1 pc)
❷ – Power cable type powerCON (1 pc)
❸ – Omega handle (1 pc)
❹ – User Manual (1 pc)

CONNECTION

The device is equipped with the following interfaces:

1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): powerCON The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.
Diagram of connection of devices by DMX cable.

The connection is performed using power cable with powerCON connector (included).
The device must be operated by qualified personnel.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions Using lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life.

Voltage Specification.

Control Menu

1. On the fixture display, four buttons from left to right:
2. MENU” button. It is the Function menu.
3. Up” button. Modify data up.
4. Down” button. Modify data down.
5. ENTER” button. Save the modified data and exit the edit state.
6. In the editing state, if the „Enter” button is not pressed, the modified data will not be saved and will be lost after shutdown.

Display Function Menu

DMX CHART

Channel Mode

8A Channel Mode

8B Channel Mode

https://flash-butrym.pl/en_US/p/DualBlaze-2x150W/779

FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL

Documents / Resources

| FLASH F7200226 2x150W DualBlaze Light [pdf] User Manual
F7200226, F7200226 2x150W DualBlaze Light, 2x150W DualBlaze Light, DualBlaze Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>