dji L2ES2212 Mavic 3 Pro Aircraft Drone Camera User Guide
- June 15, 2024
- DJi
Table of Contents
Mavic 3 Pro Quick Start Guide
v1.0 2023.03
Aircraft
The MAVIC™ 3 Pro features Omnidirectional Obstacle Sensing, an Infrared Sensing System, and a fully stabilized 3-axis gimbal with a wide camera that can shoot up to 5.2K video and 20-megapixel photos. DJI signature technologies such as Obstacle Avoidance and Intelligent Flight Modes like HyperLapse, ActiveTrack, QuickShot, Panorama, and Advanced Pilot Assistance Systems, help you capture complex shots effortlessly.
-
Gimbal and Camera
A. Telephoto Camera
B. Medium Telephoto Camera
C. Wide Camera -
Horizontal Omnidirectional Vision System
-
Auxiliary Bottom Light
-
Downward Vision System
-
Infrared Sensing System
-
Front LEDs
-
Motors
-
Propellers
-
Aircraft Status Indicator
-
Landing Gear (antennas included)
-
Upward Vision System
-
Intelligent Flight Battery
-
Battery Level LEDs
-
Power Button
-
Battery Buckles
-
Charging/Upgrading Port (USB-C)
-
microSD Card Slot
Remote Controller
The DJI RC features O3+, the latest version of DJI’s signature OCUSYNC™ image transmission technology, and can transmit a live HD view from the camera of an aircraft at a distance of up to 15 km. Users can connect to the internet via Wi-Fi and the Android operating system comes with a variety of functions such as Bluetooth and GNSS.
- Antennas
- Back Button
- Control Sticks
- RTH Button
- Flight Pause Button
- Flight Mode Switch
- 5D Button
- Power Button
- Confirm Button
- Touchscreen
- microSD Card Slot
- USB-C Port
- Mini HDMI Port
- Gimbal Dial
- Record Button
- Status LED
- Battery Level LEDs
- Focus/Shutter Button
- Camera Settings Dial
- Air Vent
- Control Sticks Storage Slots
- Customizable C1 Button
- Speaker
- Customizable C2 Button
- Air Intake
Watching Tutorial Videos
Charging the Batteries
Checking the Battery Levels and Powering On/Off
Press once to check the battery level.
Press, then press and hold to turn on/off.
Preparing the Aircraft
1. Unfold the front arms and the propellers.
2. Unfold the rear arms and the propellers.
3. Unfolded
Preparing the Remote Controller
- Remove the control sticks from the storage slots, then attach the control sticks.
- Unfold the antennas.
Preparing for Takeoff
1. Power on the remote controller
2. Power on the aircraft
3. Launch DJI Fly App
Flight
• Auto Takeoff / Landing
Auto Takeoff Auto Landing
• Manual Takeoff / Landing
Combination stick command to start/stop the motors
OR
Left stick up (slowly) to take off
Left stick down (slowly) until you touch the ground
Hold a few seconds to stop the motors
· Remote Controller Operation
Left Stick
- Up
- Down
- Turn Left
- Turn Right
Right Stick
- Forward
- Backward
- Left
- Right
Specifications
- Aircraft (Model: L2S/L2E)
| Takeoff Weight | 958 g |
|---|---|
| Max Flight Time | 46 minutes |
| Operating Temperature | 14° to 104°F (-10° to 40°C) |
| Operating Frequency | 2.400-2.4835 GHz; 5.725-5.850 GHz；5.17-5.25 GHz |
| Transmitter Power(Eirp) | 2.4GHz<20 dBm (CE, UKCA) |
5.2GHz<23 dBm (CE)
5.8GHz<14 dBm (CE, UKCA)
- Intelligent Flight Battery
| Capacity | 5000 mAh |
|---|---|
| Battery Type | LiPo 4S |
| Energy | 77 Wh |
| Charging Temperature | 41° to 113°F (5° to 45°C) |
- Remote Controller (Model: RM510)
| Weight | Approx. 750 g |
|---|---|
| Battery | 18650 Li-ion (5000 mAh @ 7.2 V) |
O3+
Operation Frequency| 2.400-2.4835 GHz; 5.725-5.850 GHz
Wi-Fi
Protocol| WiFi Direct, Wi-Fi Display, 802.11b/a/g/n/ac/ax
2×2 MIMO
Operation Frequency| 2.400-2.4835 GHz; 5.725-5.850 GHz
Bluetooth
Protocol| Bluetooth 5.1
Operation Frequency| 2.400-2.4835 GHz
FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI Mavic 3 Pro, DJI Mavic 3 Pro Cine
Model Number: L2S, L2E
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above
mentioned model was tested to demonstrate complying with all applicable FCC
rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The aircraft complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm during normal operation. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference.(2)This device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
EU & UK Compliance Notice
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that
this device (L2S, L2E) is in compliance with the essential requirements and
other relevant provisions of the Directive 2014/53/EU.
A
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
c
GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that
this device (L2S, pL2E) is in compliance with the essential requirements and
other relevant provisions of Radio Equipment Regulations 2017.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>