VEVOR CY-SF18 Snow Roof Rake User Manual

Table of Contents

VEVOR-CY-SF18-Snow-Roof-Rake-PRODUCT

Important Safety Instructions:

Read and understand all instructions in the user manual before operating the roof rake.
Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
Assemble the roof rake on a flat, level, hard, and smooth surface capable of safely supporting it.
Do not assemble the roof rake when tired or under the influence of alcohol, drugs, or medication.
Keep bystanders out of the assembly area.
Inspect the roof rake before every use and do not use it if any parts are loose or damaged.
Do not sit or stand on the roof rake. It is not a toy and should not be used by children.
The shape and color of the slip cloth are for reference only.
The actual shape may vary.

Assembly Instructions:

Lay Part A within Part C as shown in the picture. Insert Bolt 1 (2 pcs.) and Nut 2 (2 pcs.) into the corresponding holes but do not tighten them.
Connect Part B, Part A, and Part C. Insert Bolt 1 (2 pcs.) and Nut 2 (2 pcs.) into the corresponding holes and tighten them using Wrench 3 and Allen Key 4.
Attach Part F to Part A using Wrench 3 and Allen Key 4 to tighten. You can attach up to four (4 pcs.) Part D onto Part 4 before attaching the handle (Part E), depending on the length needed to clean your roof.
Hang one end of the hook (Part G) to the ring of Part A and the other end to the hole of the handle (section 3) to secure Part A and prevent it from shifting.

Please refer to the user manual for any additional information or clarification on the parts listed in the manual.
For technical support or warranty inquiries, please visit www.vevor.com/support.
We continue to be committed to providing you tools with at a competitive price.
Save Half”, “Half Price” or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and do not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

WARNING:
Read this material before using this product. Failure to do so can result in serious injury.

Assemble only should be according to these instructions. Improper assembly can result in hazards.
Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
Keep the assembly area clean and well-lit.
Keep bystanders out of the area during assembly.
Do not assemble when tired or when under the influence of alcohol, drugs or medication.
The product capabilities apply to properly and completely assembled products only.
Assemble on a flat, level, hard and smooth surface capable of safely supporting the roof rake.
For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

DO NOT SIT OR STAND ON THIS ITEM.
This product is not a toy. Do not allow children to play with or near this item.
Use as intended only.
Inspect before every use; do not use if parts are loose or damaged.
The shape and color of slip cloth are for reference only. The actual shape shall prevail.

VEVOR-CY-SF18-Snow-Roof-Rake-FIG-1

STEP1 Lay Part A within Part C as shown in the picture. Insert Bolt 1 (2 pcs.) and Nut 2 (2 pcs.) into the corresponding holes but do not tighten them.
STEP2 Connect Part B, Part A, and Part C. The details of how Part B and Part A joined are shown in the following picture. Insert Bolt 1 (2 pcs.)and Nut 2 (2 pcs.) into the corresponding holes and tighten all of them with Wrench 3 and Allen Key 4.
STEP3 Attach Part F to Part A, using Wrench 3 and Allen Key 4 to tighten. Depending on the length needed to clean your roof, you can attach up to four (4 pcs.) Part D onto Part 4, before attaching the handle (Part E).
STEP5 Hang one end of the hook(Part G) to the ring of Part A and the other end to the hole of the handle (section 3) to secure Part A to prevent it from shifting.

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai EC REP: SHUNSHUN GmbH. Römeräcker 9 Z2021,76351
Linkenheim-Hochstetten, Germany
UK REP Pooledas Group Ltd. Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to the USA : Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
Made In China
Technical Support and E-Warranty Certificate www.vevor.com/support

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us: Technical Support and E-Warranty Certificate www.vevor.com/support