VEVOR SKF-S25J Commercial Lce Maker Instruction Manual

VEVOR SKF-S25J Commercial Lce Maker

Product Information

The SKF-S25J is an electric ice maker designed for residential and non-retail use. It has a rated voltage of AC120V and operates at a frequency of 60Hz. With a power input of 350W and a rated current of 3A, this ice maker is capable of producing up to 62 lbs of ice per day. It has a refrigerating system with shock protection type R290/24g I and is insulated with Cyclopentane foam material. The ice basket capacity is 5 lbs, allowing for ample storage of ice.

Product Usage Instructions

Installation and Setup

• Caution: Installation must be performed by professionals.
• Warning: The drain of the inner tank must always be connected to a floor drain. The drain of the internal water tank should only be connected to a floor drain after cleaning or it must be plugged.

Installation Requirements

Lifting Hazard: It is recommended to have two people move and install the ice maker to prevent injury.

Prepare for Use

1. Carefully remove all packing material, avoiding the use of sharp tools that could damage the ice maker.
2. Ensure all components are present, including an assembled filter, 1 drainage pipe, 2 silica plugs, drip tray, and drip tray cover.
3. Place the ice maker upright on a flat, level surface and plug it into a power outlet.
4. Clean the ice maker thoroughly before first use.

INSTRUCTION

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.）

READ ALL INSTRUCTIONS BEFORE USING

IMPORTANT SAFETY INFORMATION

WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this electric appliance. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury
Save all warnings and instructions for future reference.

SAFETY INFORMATION

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and the word “WARNING” or “CAUTION”. These words are defined as

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
CAUTION: ICE CAN’T BE STORED IN THE ICE BIN DURING NIGHTTIME, IT’S NOT A FRIDGE, AND ICE WILL BE MELTED INTO WATER AND FLOW OUT OF THE MACHINE.

WARNING: To reduce the risk of fire, explosion, electric shock, exposure to UV radiation, or injury when using your ice maker, follow these basic safety precautions:

• This product must be properly installed and located in accordance with the Installation instructions before it is used.
• When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.
• A high-humidity environment will increase the risk of short circuits or electric shock. If in doubt, please cut off the power supply of the ice maker.
• Do not exceed power outlet ratings. It is recommended that the ice maker is connected to its own circuit. Use only standard electrical supply that is properly grounded in accordance with the National Electric Code and local codes and ordinances.
• If the ice maker is brought indoors from outdoors during the wintertime, give it a few hours to warm up to room temperature before plugging it into a power source.
• Do not store explosives, such as combustion-supporting sprays in the appliance.
• The machine is intended to be used in household and similar applications such as:
  • kitchen areas in shops, offices, and other working environments;
  • farmhouses
  • by clients in hotels, motels, and other residential-type environments;
  • Catering industry and similar non-retail industry.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
• Avoid direct sunlight and make sure that The machine is used in the household and without obstacles surrounded, by good ventilation place. There must be 50cm at least between the four sides of the machine with the wall.
• Do not tip the machine over.
• We do not recommend the use of an extension cord, as it may overheat and become a risk of fire.
• Don’t use any liquid other than water in the unit to make the ice.
• Do not store or use flammable vapors or liquids near this product.
• Do not allow children to climb, stand, or hang on the ice maker. They could seriously injure themselves.
• Do not use water that is microbiologically unsafe or of unknown quality.
• To avoid the risk of injury, place the power cord in such a way it cannot be pulled on by children or cause a tripping hazard.
• Place the power cord in such a way that it is not in contact with hot surfaces.
• Do not operate if any component, including the cord or plug, is damaged.
• Unplug the product before cleaning or repairing, and when not in use. (Note: If the machine needs repair, it is strongly recommended that it be operated by professionals. Type Y attachment: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.)
• Do not immerse any part of the product in water.
• Do not plug or unplug the products with wet hands.
• Do not place the power cord on the carpet or other heat sources
• Do not attempt to disassemble, repair, modify, or replace any part of your product.
• Use this product only for its intended purpose as described in this user manual.
• If the power cord is damaged, it must be replaced by the manufacturer or similar professionals in order to avoid danger.
• Do not use any accessories not recommended by the manufacturer.
• The foaming materials inside is combustible which must be kept away from fire.
• It’s forbidden to pull the cable to unplug the plug, pulling the plug is a must.
• Except for the method recommended by the manufacturer, no mechanical tools or other methods shall be used to accelerate the defrosting process. Do not damage the refrigeration circuit.
• There are high-pressure, flammable, and explosive refrigerants in the compressor. Do not damage the refrigeration system. Care or repair should be carried out by professionals. Be especially careful when installing and transporting.
• There are heat insulation materials in the ice maker, which are combustible materials and must be kept away from fire sources. Repairs must be carried out by the manufacturer or professionals. Scrap must be disposed of by the designated recycling department.

Product specifications

Quick introduction

Installation and setup

Caution: Installation must be installed by professionals.

Warning:

• The drain of the inner tank must be always connected to a floor drain.
• The drain of the internal water tank (Only connect to a floor drain after cleaning, or it must be plugged)

Installation requirements

CAUTION: Lifting Hazard: It is recommended to have two people move and install the ice maker in order to prevent injury.

The product is designed to be installed indoors. Do not use your ice maker outdoors.

• The product must be installed upright on a flat, level surface that is able to support the total weight when full of water.
• Ensure a minimum of 50cm clearance around the side and back walls of the ice maker for proper air circulation.
• Install the product in a well-ventilated area with an ambient temperature between 3℃ and 40℃.
• Do not place the product near heat sources such as ovens or cooktops.
• Do not place the product in direct sunlight or rain.
• Do not place any stuff on the top of the machine.

Prepare for use

1. Carefully remove packing material. Do not use sharp tools that can damage the ice maker.

2. Ensure all components are present.
   (An assembled filter, 1 drainage pipe, 2 silica plugs, drip tray, and drip tray cover are standard on the machine.)

3. Place the ice maker upright on a flat, level surface and plug it in.

4. Clean the ice maker before first use.

Connect to water and drain pipe

It must be connected connected to tap water. If there is a problem caused by the tap water without a filter, our company will not bear the cost of repairing.

CAUTION: The water supply pressure should be 0.1-0.4MPa; if the pressure is greater than 0.4MPa, a pressure reducing valve is required.

Use tap water as a water source
The filter you received is assembled, plug the water intake pipe firmly into the connector at the back of the machine until you can’t insert it anymore, and the other side connects to the water tap.

Drain
The drain of the inner tank must be always hooked it up to a floor drain or a container, or the water will leak to floor !The drain of internal water tank only connect to a floor drain after cleaning, or it must be plugged.

Understanding the display

Please make sure

1. The tap is on or there is water in the bottle.
2. The drain pipe was inserted into the sink or bucket
3. The machine is powered on.

Touch screen

Control board

1. Standby: Plug the power cord into the socket will make the machine enter standby mode.
2. Touch the “making ice”,” dispense ice”, and” clean” icons under standby mode, the selected indicator will blink.
3. Making ice: Touch the “Making ice” icon under standby mode or “clean” mode to make the machine start to make ice; Long touch this icon for 2 seconds during “Making ice” mode to make the machine enter standby mode.
4. Dispense ice : Touch this icon under standby or “making ice” mode will make the machine dispense ice, touch it again to stop dispensing. If no ice is dispensed within 30, it will stop dispensing automatically. If the outlet is jammed, long press this icon for 5s, ice cubes will be dispensed automatically after 25s.
5. Large / Clean : Touch this icon during “making ice” mode will make the machine dispense ice continuously for 5min, touch again will make the machine stop dispensing ahead of time.
   Long touch the icon for 3s under standby mode to start the self-cleaning progress, and touch again to stop the self-cleaning progress. After cleaning, unplug the outlet to drain. Make sure the drain pipe is connected before starting the machine.

NOTE:

1. Clean mode and ice-making mode can’t be operated at the same time.
2. The two outlets of the machine must be hooked up to a floor drain after cleaning. Observe the water flow to avoid overflow.
3. After that, the outlet of the internal water tank must be plugged.

Ice full: As infrared rays detect no ice fall over 2 min, the machine will stop and the “ice full” indicator will be on, the machine will restart to work as you take some ice out or after the ice melts.
Fault: If no ice falls over 15 minutes for the first cycle, the machine will stop and the FAULT indicator will be on. After that, if there is no ice falling over 3 minutes, the machine will stop working and the FAULT indicator will be on.

Warning: The ice machine is used to make and store ice, wash your hands before taking ice.

Clean and care

For long-term storage

• a) Power off the machine and pull the plug.
• b) Turn off the faucet and remove the inlet pipe
• c) Take out all the ice, and drain the water inside
• d) Dry the ice bin and interior.

Daily cleaning
During the working time, more and more scales will precipitate in the water tank. If it is not cleaned in time, it will cause malfunctions. Generally, it needs to be cleaned once a week. Take all nugget ice out, add 10% edible citric acid to the water tank during cleaning, touch the clean icon, it will take about 5min to finish the clean procedure, and then repeatedly rinse with fresh water before using. Observe the water flow at any time during the cleaning mode to avoid overflow, if the water is too swift which leads to overflow, turn down the tap.

Clean interior

NOTE: Pull the plug before cleaning or maintaining
To make the machine work normally, check and clean the condenser annually.
Don’t use alcohol to clean the in-wall of the machine, it will break the plastic materials.

Clean exterior
Clean the exterior with detergent weekly

Common malfunction analysis

The machine doesn’t work

| Power cord| The plug didn’t plug into the socket| Plug into socket
The fuse of PCB| The fuse is broken| Replace the fuse
PCB| Broken| Replace the PCB
Ice full| Ice full| Take out some ice
Proximity switch| The proximity switch is broken| Replace the proximity switch
Power supply| No power or lower voltage| Contact the power supply bureau
Water supply| No water or water pressure is low| Check the water  source  and its

pressure

Inlet valve| The inlet valve is broken| Replace the inlet valve

The compressor didn’t work or stopped working suddenly

| Power supply| No power or lower voltage| Contact the power supply bureau
The air inlet is congested| Ensure     that      the     machine’s surrounding space of at least 50

cm of clear of any objects

| The air inlet is congested
Condenser| Too much dust covered| Clean the condenser
Refrigerant| Refrigerant leaked| Contact after-sales service
compressor| The connection wire is broken off| Contact after-sales service

No water in the water tank

| Water supply| No water or water pressure is low| Check the water  source and  its

pressure

Inlet valve| The inlet valve is broken| Replace the inlet valve

Water leakage

| Water inlet| The water inlet is loosened| Re-tightened the water pipe
Drain pipe| Didn’t connect to the drain pipe or sewer| Connect to drain pipe or sewer
Float| Jammed or broken| Adjust or replace
The stoppage indicator is on| No ice during 15min| Refrigeration system| Contact after-sales service
There are ice falls into the

ice basket

| Infrared ray is broken| Contact after-sales service
Take too long to| Water pressure| Lower water pressure| Check the water source
---|---|---|---
make ice| | |
Water

temperature

| The water temperature is high| Change  to  a  water  source  of  lower

temperature

Ambient

temperature

| The ambient temperature is too

high or too low

| Change to a place of lower temperature
Refrigerant| Refrigerant leakage| Contact the after-sales
Productions of ice cubes are low and the cube ice is too thin| Condenser| Too much    dust  covered

causes bad ventilation,, will take too long to make ice

| Clean the condenser
Water pump| Water pump broken| Replace a water pump
Ambient

temperature

| Ambient     temperature    is

relative high

| Change to a place of lower temperature
Air inlet| The air inlet is congested| Ensure that the machine’s surrounding

space of at least 50cm is clear of any objects

Add            water indicator is on| Water tank| No water inside| Check the water supply
Water in the tank| Check the float

Noise

| Condenser| The    sound    of    the    fan

scrapes    against condenser

| Contact the after-sales
Valve| It  worked  too  long  for

single time

| Restart the machine after the solenoid

valve cool off

Evaporator| In the beginning of making

ice

| Normal

RoHS

Nugget ice maker

Category

| ****

Accessories

| Harmful substance

Pb

| ****

Hg

| ****

Cd

| ****

Cr(VI)

| ****

PBB

| ****

PBDE

Hardware

| Refrigeration

Component

| ○| ○| ○| ○| ○| ○
Screws| ○| ○| ○| ○| ○| ○
Sheet metal| ○| ○| ○| ○| ○| ○

Electricity

| Fan component| ○| ○| ○| ○| ○| ○
Power cord| ○| ○| ○| ○| ○| ○
PCB| ×| ×| ×| ○| ○| ○
Compressor| ○| ○| ○| ○| ○| ○
Component| component| | | | | |
---|---|---|---|---|---|---|---

Plastic injection

| Plastic panels| ○| ○| ○| ○| ×| ×
Water tank| ○| ○| ○| ○| ○| ○
Inner shaft| ○| ○| ○| ○| ○| ○
Feet| ○| ○| ○| ○| ○| ○
Ties| ○| ○| ○| ○| ○| ○
Silicon      gel

plugs

| ○| ○| ○| ○| ○| ○

Wrapping

| Carton| ○| ○| ○| ○| ○| ○
Foam| ○| ○| ○| ○| ○| ○
PE bag| ○| ○| ○| ○| ○| ○
Labels| ○| ○| ○| ○| ○| ○
Manual| ○| ○| ○| ○| ○| ○

Manufacturer : Cixi Jirui Electric Appliance Co., Ltd
Add: 118# Nanxin Road, Zonghan Street, Cixi City, Zhejiang Province
E-mail:CustomerService@vevor.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>