Eurolite THA-350F COB LED Lens Headlights User Manual

Eurolite THA-350F COB LED Lens Headlights User Manual

LED THA-350F WW/CW

Theater Spot

DANGER! Electric shock caused by short-circuit

Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to

• be qualified
• follow the instructions of this manual
• consider this manual to be part of the total product
• keep this manual for the entire service life of the product
• pass this manual on to every further owner or user of the product
• download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features

Fresnel spotlight, 350 W LED, variable color temperature, CRI >90, zoom

• Motorized zoom adjustable via DMX or manually on the device
• Electronic dimmer (0-100%)
• Temperature-protected handle
• Barndoors included in delivery
• Mains input and output for power linking up to 8 units
• 1 powerful LED 350 W COB (chip-on-board) 2in1 BCL CW/WW (homogenous color mix)
• Variable color temperature 2700 K – 6500 K
• Can be operated in 4; 5 CH mode
• The device is cooled by temperature-controlled fan
• Controlling by stand-alone; Master/slave function; DMX
• Flicker-free
• Effect: Strobe effect
• With a beam angle of 11° – 41°
• Very high color rendering index (CRI)
• With mounting bracketLCD display

SAFETY INSTRUCTIONS

WARNING!

Please read the safety warnings carefully and only use the product as described in this manual to avoid accidental injury or damage

Intended use

• This device is an LED theater spot for creating decorative lighting effects. This device is designed for professional use in the field of event technology, g. on stage. It is not suitable for household lighting.
• Only use the device according to the instructions given Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or non-compliance with the safety In such cases, the warranty/guarantee will be null and void.
• Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty

Danger due to electricity

• The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to
• To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the
• Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
• The mains outlet must be easily accessible so that you can unplug the device quickly if need
• Never touch the mains plug with wet or damp There is the risk of potentially fatal electric shock.
• The mains cable must not be bent or Keep it away from hot surfaces or sharp edges.
• Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the
• Unplug the device during lightning storms, when unused for long periods of time or before
• Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical
• Do not place any objects filled with liquids on the
• Do not place any open sources of fire, such as burning candles, on or directly next to the
• Make sure that objects cannot fall into the device, in particular metal
• Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions
• Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around Never leave this device running unattended.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their

Warning – risk of burns and fire

• The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature
• The housing temperature (Tc) can be up to 60°C during Avoid contact by persons and materials.
• Do not illuminate surfaces within 20 cm of the This value is indicated on the device by the symbol.
• Do not use the device near highly flammable Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.

Warning – risk of injuries

• Do not look directly at the light Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
• Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60598-2-17.
• If you lack the qualification, do not attempt the installation yourself, but instead use a professional Improper installation can result in bodily injury and or damage to property.
• The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety
• For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the
• For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all

Caution – material damage

• This device must not be connected to the mains voltage by means of a
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without
• Never switch the device on and off in short This will considerably reduce the service life of the device.
• If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
• If a serial number label is affixed to the device, do not remove the label as this would make the guarantee

DESCRIPTION OF THE DEVICE

• Mounting bracket
• Fixation lever
• Safety eyelet
• Fresnel lens
• Barndoor fixation brackets

Temperature-protected handle

Manual zoom-out button
Manual zoom-in button
DMX signal indicator
DMX In (5-pin)
DMX Out (5-pin)
DMX In (3-pin) DMX Out (3-pin)
On/off switch
Power input
LCD with operating buttons
Power output
Fuseholder

INSTALLATION

WARNING! Risk of injury caused by falling objects

Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations.

The device may be placed via the mounting bracket on a lighting stand or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

• The rigging structure must support at least 10 times the weight of all fixtures to be installed on
• Block access below the work area and work from a stable platform when installing the
• Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the Accessories section for a list of suitable rigging hardware.
• Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. An appropriate eyelet is mounted on the device for fixation of the safety Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm
• To align the device, release the fixation levers at the mounting bracket, adjust the desired inclination angle and tighten the fixation levers.

After installation, the device requires inspections periodically to prevent the possibility of corrosion, deformation and looseness

Installation on a lighting stand

Please note: All devices, lighting effects and crossbeams attached on a stand must be secured with a secondary attachment!

• Attach an appropriate adapter or TV-adapter to the top end of the stand and fasten it with the fixation
• Attach the mounting bracket of the theater spot onto the TV-adapter and tighten the fixation
• The given carrying capacity of the stand must not be Please consult the appropriate user manual for further information.
• To align the device, release the fixation levers at the mounting bracket, adjust the desired inclination angle and tighten the fixation
• After installation, the device requires inspections periodically to prevent the possibility of corrosion, deformation and

CONNECTIONS

DMX512 control

A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin and 5-pin XLR connectors for DMX connection.

• Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX
• Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are
• At the last unit, the DMX cable has to be Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
• If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX splitter to ensure proper data

XLR connection

Connection to the mains

The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

• The device is equipped with a lockable power input Fix the mains cable and turn it to the right until it locks. Connect the device via the mains cable to a grounded mains socket. Thus the unit is switched on.
• To switch off the unit, disconnect the power
• Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.

Power supply of further devices

The jack POWER OUT allows for power supply of further devices. To interconnect several devices, connect the jack POWER OUT to the input POWER IN of the next unit until all units are connected. Matching power cables are available as accessories. In this manner, up to 8 devices can be linked at 230/240 input voltage and up to 4 devices at 110/115 input voltage.

OPERATION

With the power switch, you can switch the device on and off. After connecting the device to the mains it is ready for operation. The display shortly shows the firmware version and model name. The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains. The device can be operated in stand-alone mode via the control board or in DMX-controlled mode via any commercial DMX controller.
During the reset, the motor is trimmed and then the device is ready for use.
Press the MODE button to access and browse through the main menu. Press the ENTER button in order to select the desired menu item. You can change the selection by pressing UP or DOWN. Confirm every selection by pressing the ENTER button. The functions provided are described in the following sections.

Manual Zoom Buttons

The manual zoom buttons are located on the rear of the device, as described under the chapter Description of the Device.
Zooming : Press the Zoom-In or Zoom-Out button to manually adjust the zoom step by step.

Menu structure

DMX Adr

001

| DMX Adr 001 – 511| Setting the DMX starting address

DMX Loss Off

| DMX Off| Device switches off automatically when separated from DMX signal
DMX Hold| Device runs the last set program in Stand Alone

Mode when separated from DMX signal

Channel 4|  | Setting DMX Mode
4CH| 4-Channel DMX Mode
5CH| 5-Channel DMX Mode
Master Off| MASTER: OFF| Slave Mode on
MASTER: ON| Master Mode on

Perform P-000

| 000 – 004| Auto Programs (Master-Mode)
000| No function
001| WW
002| CW
003| WW und CW
004| Color temperature changes automatically

Man Dim

|  | Manual Dimmer (Master-Mode)
MAN DIM

C–WHITE

| 0-255 with increasing brightness
MAN DIM

W–WHITE

| 0-255 with increasing brightness

Fan Auto

| FAN AUTO| Fan runs automatically
FAN

ON

| Fan on

Display

|  | Display shutoff time
BACK LIT

AUTO-5

| Display shuts off after 5 seconds
BACK LIT

AUTO-10

| Display shuts off after 10 seconds
BACK LIT

AUTO-30

| Display shuts off after 30 seconds
BACK LIT

AUTO-60

| Display shuts off after 60 seconds
BACK LIT

ON

| Display on
BACK LIT

0-255

| Set display brightness

Info

| LED TEMP ###| LED-Temperature| ****

Read out only

HOURS #####| Running time
SERIAL ########| Serial number
SFTVER VER ##| Software version

Stand-alone mode

In stand-alone mode, the device can be used without controller. Disconnect the device from the controller and call up the menu you want to use. Please refer to the instructions under Menu structure.

Master/slave operation

Several devices may be interconnected (max. 32). Then all slave units can be synchronized and controlled with the master unit without the need for a DMX controller. The devices must be set to the corresponding operating modes.

• Configure all slave units before connecting the master unit. Press the MODE button so many times until MASTER OFF is indicated on the display. Confirm with the ENTER Then via the UP/DOWN buttons set each Slave device to MASTER: OFF and confirm with ENTER.
• Connect the DMX output of the master unit to the DMX input of the first slave unit. Then connect the DMX output of the first slave unit to the DMX input of the second slave unit, until all units have been connected in a chain. Make sure the master unit is the first in the chain. Do not connect a DMX controller to the DMX input of the master unit.
• Now press the MODE button so many times until MASTER OFF is indicated on the display. Confirm with the ENTER Then via the UP/DOWN buttons set the Master device to MASTER: ON and confirm with ENTER.
• Select the desired show mode at the master unit (See Menu Structure ). The interconnected devices will now operate

DMX operation

Setting the number of DMX channels and the DMX starting address

For operation with a controller with DMX512 protocol, the device is equipped with 5 control channels. However, it can also be switched to a mode with 4 channels if different functions are required. To be able to operate the device with a DMX controller, the DMX starting address must be set. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

• Press the MODE button so many times until DMX Adr 001 is indicated on the Confirm with the ENTER

button. Via the UP/DOWN buttons you can set the desired starting address. Confirm with the ENTER button.

• In order to set the desired DMX channel mode, press the MODE button until Channel: 04 is indicated on the display and press ENTER. Use the buttons UP/DOWN to select the desired DMX channel mode (4CH / 5 CH). Confirm with the ENTER
• The DMX signal indicator LED on the device rear will flash when DMX signals are being received (see

Description of the Device ).

Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are defined to the same address, they will work synchronously.

Functions in DMX mode

4-  channel mode

1

Zoom

| 000 – 255| From narrow to wide
Channel:| Value             Function:
---|---

2

Strobe

| 000 – 031| No function
032 – 095| Linear strobe effect with increasing speed
096 – 159| Pulsing strobe effect with increasing speed
160 – 223| Random strobe effect with increasing speed
224 – 255| LED on
Channel:| Value             Function:
---|---
3

WW LED

| 000 – 255| Intensity from 0 – 100%
Channel:| Value             Function:
---|---
4

CW LED

| 000 – 255| Intensity from 0 – 100%

channel mode

1

Zoom

| 000 – 255| From narrow to wide
Channel:| Value             Function:
---|---

2

Strobe

| 000 – 031| No function
032 – 095| Linear strobe effect with increasing speed
096 – 159| Pulsing strobe effect with increasing speed
160 – 223| Random strobe effect with increasing speed
224 – 255| LED on
Channel:| Value             Function:
---|---
3

WW LED

| 000 – 255| Intensity from 0 – 100%
Channel:| Value             Function:
---|---
4

CW LED

| 000 – 255| Intensity from 0 – 100%
Channel:| Value             Function:
---|---
5

Master Dimmer

| ****

000 – 255

| ****

Total brightness from 0 – 100%

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lens, in particular, should be clean to ensure that light will be emitted at maximum brightness.

• Disconnect the device from power and allow it to cool before
• Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the Make sure that no liquids can enter the device.
• The device must be dry before reapplying power.

There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

Replacing the fuse

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

• Disconnect the device from power and allow it to
• Open the fuse holder at the mains connection with a fitting
• Remove the old fuse from the fuse holder and replace it with a new
• Carefully push the fuse holder back into its position before reapplying

PROTECTING THE ENVIRONMENT

Disposal of old equipment

When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.
You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

cord with safety plug
Power output:| P-Con (gray), mounting version
Fuse:| 5 x 20 mm, T 3,15 A Fuse replaceable
Lamp type:| LED lamp
LED:| 1 x 350 W COB (chip-on-board) 2in1 BCL CW/WW (homogenous color mix)
Color temperature:| 2700K – 6500K adjustable
Equipment:| Zoom motor-driven
DMX channels:| 4; 5
DMX input:| 3-pin XLR (M) mounting version
5-pin XLR (M) mounting version
DMX output:| 3-pin XLR (F) mounting version
5-pin XLR (F) mounting version
Cooling:| Temperature-controlled fan
Control:| Stand-alone; Master/slave function; DMX
Beam angle (1/2 peak):| 11 – 27°
Beam angle (1/10 peak):| 22 – 41°
Color rendering index (CRI):| 95 Ra
Housing color:| Black
Attachment system:| Mounting bracket
Display type:| LCD display

Dimensions:

| Length: 43,5 cm
Width: 28,5 cm
Height: 38,5 cm
Weight:| 10,5 kg

Accessories

Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5 97297 Waldbüttelbrunn Germany D00147009 Version 1.0 Publ. 04/04/2023

Read More About This Manual & Download PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>