Neo BLINDER-MKIII-IP LEDS High Performance Professional Blinder User Manual

Neo BLINDER-MKIII-IP LEDS High Performance Professional Blinder

Product Information

The BLINDER MKIII IP is a high-performance professional blinder with 4 X 100W 3000K LEDs. It is designed for use in various applications such as concerts, stage performances, and events where powerful and dynamic lighting effects are required.

Specifications

Introduction

For your own personal safety, it is important to read and understand the user manual completely before attempting to install or operate the BLINDER MKIII IP. Failure to follow the instructions may result in damages or problems not covered by the warranty.

DMX-512 Control Connection

The BLINDER MKIII IP has a DMX 512 input fitted with 3 pin XLR connectors. It is recommended to use screened cables in compliance with EIA RS 485 specifications for proper connections.

DMX 512 Connection with DMX Terminator

In installations where the DMX cable needs to run a long distance or is in an electrically noisy environment, it is recommended to use a DMX terminator. The DMX terminator is simply an XLR plug with a 120 OHM resistor connected between pins 2 and 3. It should be plugged into the output XLR socket of the last fixture in the chain.

Product Usage Instructions

Display Menu

The BLINDER MKIII IP features a display menu that allows you to access various settings and functions. The following options are available:

• Address
• Config Mode
• DMX Address Setting
• Channel Mode
• Keep Screen On
• Keep DMX Data
• Fast Dimmer
• System Info
• Temperature
• Led All On
• Auto Test
• LED (Warm) White
• LED Amber Strobe
• Auto Mode 1
• Auto Mode 2
• Auto Mode 3

DMX Functions and Values

The BLINDER MKIII IP supports different DMX modes with corresponding functions and values. The available modes are:

(0-100%)
3 CH MODE| Master dimmer, Fine master dimmer, Strobe| 000-255, 000-255, 000-010, 011-240, 241-255| Controls the overall intensity, fine-tuning of intensity, and
strobe effect
8 CH MODE| Warm white 1-4, Amber 1-4| 000-255 for each channel| Controls the intensity of warm white and amber LEDs for
different lighting effects
13 CH MODE| Master dimmer, Fine master dimmer, Strobe, Warm white 1-2,
Amber 1-2| 000-255 for each channel| Controls the overall intensity, fine- tuning of intensity,
strobe effect, and warm white/amber LEDs
14 CH MODE| Master dimmer, Fine master dimmer, Strobe, Warm white 1-2,
Amber 1-2, Auto mode, Dimmer mode| 000-255 for each channel| Controls the overall intensity, fine-tuning of intensity,
strobe effect, warm white/amber LEDs, and different operating
modes

Please refer to the user manual for more detailed instructions on setting up and using the BLINDER MKIII IP.

4 X 100W 3000K LEDS HIGH-PERFORMANCE PROFESSIONAL BLINDER

USER MANUAL
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE

OVERVIEW

BLINDER MKIII IP
4 X 100W 3000K LEDS HIGH-PERFORMANCE PROFESSIONAL BLINDER

BLINDER MKIII IP is a LED professional blinder for outdoor use powered by 4 x 1 0 0 W 3000k LED + 10W amber SMD. Thanks to its chip-on-board technology it reaches an amazing power and coverage. Its 4 outputs have independent focus regulation and can be controlled separately thanks to its pixel by pixel technology. Ideal for big scenarios, Neo Blinder MKIII IP is the nowadays response to the classic & powerful MiniBrut, adding a soft dimming and strobe effects that make it stand out naturally apart from an ideal power/consumption relation.

Specifications
Source & Optics

• Light Source: 100W 3000k LED + 10W amber SMD for each eye, no ultraviolet radiation.
• Average lifespan: 50,000 hours.
• Power: 450W
• Beam angle: 60º
• Color temperature: 8000K CRI>95

Effects & Functions

• Diecasting heatsink, convection cooling, no noise;
• Temperature sensor to extend the lamp life;
• 7 000 Hz LED scan rate
• 16 Bit Dimmer

Control

• Channel mode: 1/3/8/13/14 DMX channels
• Display mode: LCD display, key + touch dual operation mode.
• DMX Mode /Master slave mode;

Physical

• IP65/ IP4 0 selectable;
• Weight: 12 Kgs

INTRODUCTION

For your own personal safety, please read and understand this manual completely before you attempt to install or operate this unit!

• The electric connection must carry out by qualified person. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
• Make sure that the available voltage is not higher than stated at the end of this manual.
• Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.
• Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the p ower cord by the plug. Never pull out the plug by tugging the power cord.

CAUTION!
Never look directly into the light source, as sensitive persons may suffer an epileptic shock.

IMPORTANT:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.

DMX-512 CONTROL CONNECTION

The product has a DMX 512 input fitted with 3 pin XLR connectors.
Screened cables in compliance with EIA RS 485 specifications and the following characteristics must be used for connections:

• 2 conductors plus screen;
• 120 Ohm impedance;
• Low capacitance;
• Max. transmission rate 250kBaud.

DMX 512 CONNECTION WITH DMX TERMINATOR

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 OHM resistor connected 3 between pins 2 and 3, which is then plugged into the output XLR between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture in the chain.socket of the last fixture in the chain.

DISPLAY MENU

Config Mode

| ****

Channel Mode

| Channel 1Ch
Channel 3Ch
Channel 8Ch
Channel 13Ch
Channel 14Ch
Keep Screen On| Disable
Enable
Keep DMX Data| Enable
Disable
Fast Dimmer| Enable
Disable

System Info

| ****

Temperature

| Head 1
Head 2
Head 3
Head 4
Body
Led All On| Disable
Enable

Auto Test

| Auto Mode 1
Auto Mode 2
Auto Mode 3

LED test

| LED (Warm) White| ****

0 – 255

LED Amber
Strobe

DMX FUNCTIONS AND VALUES

1 CH MODE:

3 CH MODE:

3

| ****

Strobe

| 000-010| No function|
011-240| Strobe| Slow to fast
241-255| Random strobe| Fast to slow

8 CH MODE:

13 CH MODE:

3

| ****

Strobe

| 000-010| No function|
011-240| Strobe| Slow to fast
241-255| Random strobe| Fast to slow
4| Warm white 1| 000-255| 0-100%|
5| Amber 1| 000-255| 0-100%|
6| Warm white 2| 000-255| 0-100%|
7| Amber 2| 000-255| 0-100%|
8| Warm white 3| 000-255| 0-100%|
---|---|---|---|---
9| Amber 3| 000-255| 0-100%|
10| Warm white 4| 000-255| 0-100%|
11| Amber 4| 000-255| 0-100%|

12

| ****

Auto mode

| 000-035| No function|
036-041| Tungsten effect
042-071| Round up
072-107| Round down
108-143| Round up & down
144-215| 8-colors
216-255| Random effect

13

| ****

Dimmer mode

| 000-063| Linear|
064-127| Square|
128-191| Invert Square|
192-255| S-Curve|

14 CH MODE:

3

| ****

Strobe

| 000-010| No function|
011-240| Strobe| Slow to fast
241-255| Random strobe| Fast to slow
4| Warm white 1| 000-255| 0-100%|
5| Amber 1| 000-255| 0-100%|
6| Warm white 2| 000-255| 0-100%|
7| Amber 2| 000-255| 0-100%|
8| Warm white 3| 000-255| 0-100%|
9| Amber 3| 000-255| 0-100%|
10| Warm white 4| 000-255| 0-100%|
11| Amber 4| 000-255| 0-100%|

12

| ****

Auto mode

| 000-035| No function|
036-041| Tungsten effect
042-071| Round up
072-107| Round down
108-143| Round up & down
144-215| 8-colors
216-255| Random effect

13

| ****

Dimmer mode

| 000-063| Linear|
---|---|---|---|---
064-127| Square|
128-191| Invert Square|
192-255| S-Curve|
14| Dimmer speed| 000-254| No tungsten effect|
255| Tungsten effect|

CLEANING AND MAINTENANCE

We recommend a frequent cleaning of the device. Please use a soft lint free and moiste ned cloth. Never use alcohol or solvents!
There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by authorized dealers.
If you need an y spare parts, please use genuine parts. If the power supply cable of this device becomes

CAUTION!
Disconnect from mains before starting maintenance operation.

damaged, it has to be replaced by authorized dealers only in order to avoid hazards.
If you have further questions, please contact your dealer.

/amprogroup
/amprogroup

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>