AQUATECH SYNC Transmitter Housing Instruction Manual

AQUATECH SYNC Transmitter Housing

Product Information

The AQUATECH SYNC Transmitter Housing is a versatile housing designed to be compatible with the entire range of Water Housings. It allows for wireless control of the LUX Flash Housing when used with a Godox transmitter, providing new options for wireless off-camera flash in the water with full TTL and HSS (for Canon and Nikon only). The SYNC features a control-free design, allowing exposure control to be performed either in the camera or on the light itself. It is easily secured with 2 thumbscrews to provide a watertight seal across the clear backplate. The SYNC also features a quick-cam mount that connects to the supplied Pro Mount V3 without the need for additional tools, allowing for easy interchangeability with an action camera on the Pro Mount V3 when lighting is not required.

Product Usage Instructions

1. Before using your SYNC Transmitter Housing for the first time, please read the following instructions and care tips carefully.
2. Perform the initial setup by installing the provided additional Flash Bulkhead onto your Water Housing. Ensure it is installed correctly by performing a dunk test without your camera installed.
   • If there is any moisture or water present after the test, contact AQUATECH for assistance with reinstalling the Flash Bulkhead.
   • Note that when not using your Sync Transmitter Housing, the supplied Flash Bulkhead cap must be replaced to protect the dry connector.
   • Either the sync cable or the cap must be on the Bulkhead at all times.
3. When using the SYNC Transmitter Housing underwater, follow the best practices and ensure all initial setup instructions have been followed.
4. For maintenance and repair, contact AQUATECH directly at service@aquatech.net. Proper care will ensure your gear lasts for many years, but if any problems or damage occur, AQUATECH can provide repairs or servicing.
5. It is important to note that AQUATECH’s liability is limited to the value originally paid for the product. Losses of associated equipment, income, or any other financial costs are not covered under the warranty.
6. The product comes with a 1-year warranty. If you are not completely satisfied with the product or experience any issues, contact AQUATECH for prompt resolution. However, please note that loss or damage of equipment, personal injury, or financial loss are not covered under the warranty due to the extreme and volatile environments in which AQUATECH products are often used.

For more tips and information, visit AQUATECH’s website and YouTube channel.
Thank you for purchasing this AQUATECH SYNC Transmitter Housing.

Overview

• The SYNC Transmitter Housing is a compact and easy-to-use housing that supports a range of flash transmitters. Wirelessly connect your camera to one or multiple professional strobes, or even speedlights to create a range of lighting effects that capture your unique vision. The simple design of the SYNC connects to your water housing via our 6-pin SYNC cable system and has the ability to support TTL modes and Hi-Speed SYNC (for Canon and Nikon only). 6 Pin SYNC cables are available in a range of sizes up to 30ft, so you can float your SYNC to the surface to continue to transmit the radio signal even if you’re well below the surface.

• An amazing feature of the SYNC Transmitter Housing is the option to have the SYNC wirelessly control the LUX Flash Housing when using a Godox transmitter. This opens up a world of new options for wireless off-camera flash in the water with full TTL and HSS (for Canon and Nikon only).

• The SYNC is easily secured with 2 thumbscrews to provide an even seal across the clear backplate. As
  the SYNC is able to support multiple brands with its control-free design, the exposure control for your lights can either be performed in the camera or on the light itself.

• The SYNC features a new quick-cam mount that connects to the supplied Pro Mount V3 without the need for any additional tools. Easily interchange your SYNC Transmitter Housing with an action camera on the Pro Mount V3 when lighting is not required.

• Please read the following instructions and care tips before using your SYNC Transmitter Housing for the first time. You can also visit our website and YouTube channel for more tips and information.

What’s in the box

• SYNC Transmitter Housing (please choose the compatible camera manufacturer option)
• Pro Mount V3
• 13” 6 Pin Flash SYNC Lead
• Camera Hotshoe Connector
• AQUATECH Flash Bulkhead Connector

Nomenclature

Initial Setup

• Additional Tools Needed: Flathead screwdriver, Crescent wrench
• Open SYNC Transmitter Housing
• Then simply slide your transmitter into SYNC Hot Shoe
• Turn the transmitter on, and lineup SYNC backplate holes with SYNC housing
• Insert Turn Knob from the front of SYNC and thread it in, spinning Turn Knob clockwise.
• Remove the Flash Bulkhead plug from your Water Housing with a Flathead screwdriver turning counterclockwise, and install the supplied Flash Bulkhead onto your Water Housing making sure the two o-rings are properly in place.
• Note: the additional Flash  Bulkhead will be found bagged with your grease, hex key, Flash Sync Cable, and camera hot shoe.
• Once the Flash Bulkhead is installed onto your Water Housing, attach the female end of the Camera Hotshoe to the male end of the Flash Bulkhead.
• Once the Flash Bulkhead is installed attach the female end of the Camera Hotshoe to the male end of the recently installed Flash Bulkhead.
• Slide the Camera Hotshoe into the camera body.
• Unscrew the cap from the SYNC housing Bulkhead and housing Flash Bulkhead.
• Remove caps from both ends of the SYNC cord.
• Install one end of the SYNC cord into the SYNC Housing Bulkhead. Ensure it is correctly lined up by aligning electrical pins.
• Place the attached Sync cord Male threaded fastener over the Female threaded Bulkhead and screw in clockwise until secure.
• Attach the other end of the SYNC cord into the housing Bulkhead following the previous steps.
• To install SYNC Flash Housing you will need to have the Pro Mount installed. Please refer to the corresponding manual for Pro Mount installation.
• Push Quick Cam Mount through the slot on the Pro Mount and securely screw it into place.
• Using the SYNC Transmitter Housing in and around water

Using the SYNC Transmitter Housing underwater

• For best results please make sure you have carefully followed all initial setup instructions prior to taking your SYNC Transmitter Housing underwater.
• After installing the provided additional Flash Bulkhead onto your Water Housing, please make certain it is installed correctly by doing a “dunk” test (without your camera installed). If there is any moisture or water present after the “dunk” test is performed, please contact AQUATECH via contact@aquatech.net so we can assist you with the reinstallation of the Water Housing Flash Bulkhead. Note: when not using your Sync Transmitter Housing, the supplied Flash Bulkhead cap must be replaced. This Bulkhead is a “dry connector’ and must never be exposed to water. Either the sync cable or the cap must be on the Bulkhead at all times. This is very important to recap the Bulkhead on your Water Housing if a Sync cable is not installed.

Safety information and warning

• Do not exceed depths of 10m/33ft.
• Do not leave your Water Housing gear in temperatures greater than 50 C (125 F)

Maintenance and repair

• With proper care, your gear will last for many years. If in time you do notice any problems that come up or if there is any damage to the equipment please contact
• AQUATECH directly at service@aquatech.net for repairs or servicing.

Limit of liability

• In the event of a product warranty claim, AQUATECH is only liable up to the value originally paid for the product.
• Losses of associated equipment, income, or any other financial costs are not covered under this warranty, under any circumstances.

Warranty – 1-year product warranty

• We make every effort to ensure that our products are made from the highest quality materials and workmanship.
• Should you not be completely satisfied with one of our products, we encourage you to contact us so that we can promptly resolve any problem you may be experiencing. Our company representatives will deal with your issue quickly and decisively.
• As many AQUATECH products are often used in extreme and volatile environments, we are unable to cover for loss or damage of equipment, personal injury or financial loss.
• To reduce the risk of these losses occurring, we strongly recommend you read the relevant product instructions carefully and test the product before use.

What does the warranty cover?

• This warranty covers any defects in materials or workmanship, with exceptions stated below

What is not covered?

• The warranty does not cover damage as a result of normal wear and tear. Determination of what constitutes normal wear and tear will be at the discretion of AQUATECH service centers. The warranty guarantee only applies to the original purchaser of
  the product when purchased from AQUATECH directly or through one of our authorized dealers. Therefore, we may ask for proof of purchase. This warranty does not cover any loss of associated equipment such as cameras, lenses, or other associated equipment not sold by AQUATECH.

• Loss of income, reputation, or other financial expenses, such as personal injury are also not covered by this warranty. Shipping costs for returned products are the responsibility of the customer.

How long does the coverage last?

• This warranty runs for 1 year from the date your product is received.

What will AQUATECH do?

• AQUATECH will repair any defect that proves defective in materials and workmanship. If repairing is not possible, AQUATECH will replace the product, or, offer a store credit for the original purchase price, whichever is agreed to by the customer and AQUATECH / Retailer store.

How to get service?

• Email contact@aquatech.net and we will advise you where to send your product.

Alternatively, you may call:

• USA: + 1 714 968 6946 Australia: + 61 2 4268 3550
• Returns policy – AQUATECH online customers only:
• AQUATECH offers a 14-day return policy for new items purchased directly through our online store or at our physical store. AQUATECH will only provide exchanges or store credit for change of mind or incorrectly ordered products.
• AQUATECH will not refund any shipping and credit card costs. Please see our full return policy here.
• The customer is responsible for the shipping cost of the returned items.
• A restocking charge may be applied in some countries

How state law applies:

• This warranty gives you specific legal rights, and you may have other rights that vary according to the state or country in which you are located.

Legals

• Please practice extreme caution when diving into deep water. Only use this product in settings that are within your or other’s capabilities. Serious injuries or drowning could occur if you or others are not.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>