GHWCUSB2 Gator Dash Cam Hard Wire Kit User Manual

GHWCUSB2 Gator Dash Cam Hard Wire Kit

PRODUCT DESCRIPTION

1. Vehicle Exclusive Power Box
2. USB Connection Port
3. Male Bullet Connector
4. Ground Wire
5. Female Bullet Connector
6. Fuse (3 included)
7. Blade Fuse TAP Connector
8. Mini Blade Fuse TAP Connector
9. Micro Blade Fuse TAP Connector

INSTALLATION

1. Find fuse box in car (fuse position differs among different vehicle brands). Consult vehicle user manual for placement.

2. Open fuse box cover plate, measure the placement for wiring from fusebox to powered product.

3. Plug in USB power device

4. Locate a ground point near the fuse box. There is usually either an obvious labeled ground point or a nut / bolt that connects directly to chassis.

5. Decide whether you want your device wired to a switched or unswitched fuse. Switched circuits only have power when the vehicle is ON. Unswitched circuits always have power. You can verify if it’s switched or unswitched using a simple circuit tester.

   • NOTE : Make sure your vehicle is off and the key is not in the ignition. Choose your desired TAP fuse. Once you select the desired TAP fuse for your vehicle, attach to the power cable using the bullet connectors, then cover with plastic sleeve.
   • NOTE : This hardwire kit uses easy to put together bullet connectors. Attach each end of bullet connector until you feel a click.

6. Pull the fuse, place fuse into the TAP fuse, then re-insert into the available fuse slot.

   • Information below for Dash Cam installation

7. Starting at the USB powered product, tuck the power cable into the headliner. Once you get to the (A) pillar, there may be a sufficient gap to place power cable or it may be necessary to remove. The A pillar is the plastic piece that runs down the side separating the windshield and the door. Route the power cable along the side and behind the rest of the interior panels down towards the fuse box.

SPECIFICATIONS

• The hard wire kit can have uninterrupted power for 24 hours if connected to vehicle battery or fuse box.
• It can stay powered on when your vehicle is turned off.
• With function of auto detect battery voltage and low voltage protecting, it can cut power supply when voltage is too low, make sure the car can start normally.
• The vehicle hard wire kit is used as transforming 12V or 24V to 5V, with built-in precise switching power supply module, output voltage is more stable.
• Short-circuit protection: overcurrent and overtemperature protection, reverse connection protection, auto cut power output when it’s lower than 12V (for 12V connection) or 23.9V (for 24V connection).
• Conversion efficiency: Max 96%
• Static power consumption: about 15-18mA
• Operating temperature: Industrial level (-40°C ~ +85°C)

Electrical Parameters

• Input voltage : DC12V – 30V
• Output voltage : 5V / 1.5A
• Car low voltage protection : 12V (for 12V connection)
• Car low voltage protection : 23.9V (for 24V connection)

TECHNICAL ASSISTANCE
If you need assistance setting up or using your Gator product now or in the future, call Gator Support. Australia

• TEL : 03 – 8587 8898
• FAX : 03 – 8587 8866
• Mon-Fri 9am – 5pm AEST

Please retain this user guide for future reference. If you would like to download a digital copy of this manual, or other Gator manuals/software, please visit the gatordriverassist.com website and search for your model or click on ‘Firmware & Manuals” for information on where to find the manuals/software. This manual is considered correct at time of printing but is subject to change. For latest manuals and updates refer to the website.

Copyright © 2023 by TDJ Australia All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, copying or other electronic or mechanical methods, without the prior written permission of the author.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>