Mimaki CG-60AR Vinyl Cutter Instruction Manual

June 9, 2024
Mimaki

CG-60AR [Option]
Installation instructions for the legs
Instruction Manual

CG-60AR Vinyl Cutter

This manual explains how to assemble the legs with the main unit. Be sure to read this manual before assembling.

  • Be sure to assemble with two or more people.

Accessories

If there is a shortage of parts or a problem, please contact your local distributor or MIMAKI sales office.

Mimaki CG-60AR Vinyl Cutter -

How to tighten the screws

  1. Use hex wrench to temporarily tighten the screws (just tighten lightly).
  2. Push the hex wrench into the tightening pipe and retighten the screw.

Instruction

  1. Turn the Leg upside down to make it stand on its own by using the cushioning material (upper side) in which the main body was packed.
    • Assemble the right and left legs.Mimaki CG-60AR Vinyl Cutter - Assemble
the right

  2. Fix the Caster holder to the Leg.
    • Secure it with the 3 screws (M5x15).
    • Assemble the right and left legs.Mimaki CG-60AR Vinyl Cutter - Caster
holder

  3. Remove the cushioning material and turn the legs back in their original direction.

  4. Turn the casters inward.

  5. Use the cushioning materials (upper side) again to make the legs (Right and Left) stand on their own.
    1. Push the cushioning material until it touches the legs.
    2. Push the cushioning material until it touches the floor.Mimaki CG-60AR
Vinyl Cutter - make the legs

  6. Attach the screws (M5x15) with make a gap between.
    • Assemble the right and left legs.Mimaki CG-60AR Vinyl Cutter - Attach the
screws• Pay attention to the installation position

  7. Attach the Leg stay to the left and right legs.
    1. Hook the leg stay onto the screws installed in step 6.
    2. Tighten the screw temporarily (just tighten lightly). • Attach the leg stay so that the openings of the leftand right legs are on the inside.

  8. Lock the casters.

  9. Attach the Base plate L/R.
    • Fix the base plate to the leg with 2 screws (M5x15) while pushing it in the direction indicated by arrow. • Attach it so that the bearing is on the outside..

  10. Attach the roll bars.
    • Set the roll bar on top of the bearing installed. • Set the roll bar with four collars so that it is on the outside.

  11. Mount the Main unit on the legs.
    1. Align the protruding part of the leg with the hole on the bottom of the main unit (the ▽ mark on the side of the main unit is a guide) and insert.
    2. Make sure that the rubber foot on the bottom of the unit is set on the leg.
    3. Set the other side in the same way.Mimaki CG-60AR Vinyl Cutter - same
way• The unit should be lifted by two or more people.

  12. Push the main unit to the front side and fix it to the leg with 2 screws (M5x20).
    • Push the main unit toward the front side until there is no gap between the protrusion on the rear side of the leg and the insertion hole on the bottom of the main unit and secure it.
    • Set the other side in the same way.Mimaki CG-60AR Vinyl Cutter - other
side• Tighten the fixing screws until the convex part of the leg lightly touches the bottom of the side plate GR. Take care not to over- tighten the screws.Mimaki CG-60AR Vinyl Cutter - tighten the
screws

  13. Fully tighten the screws on the leg stay.Mimaki CG-60AR Vinyl Cutter - screws on the leg stay• Turn the roll bar manually to ensure it rotate smoothly. If it gets stuck or has trouble rotating, loosen the screws that have been tightened, adjust the left and right legs so that they are parallel, and then tighten the screws.

  14. Remove cushioning materials.Mimaki CG-60AR Vinyl Cutter - Remove cushioning

© 2021 MIMAKI ENGINEERING CO.,LTD.
D203588-13-01112022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals