FLASH P7100421 LED Par 64 COB 250W 5xWhite Mk2 User Manual

: June 4, 2024
: FLASH

Table of Contents

FLASH P7100421 LED Par 64 COB 250W 5xWhite Mk2
INTRODUCTION
SAFETY INFORMATION
- PRODUCT INFORMATION
Specification
- Photometric data
INSTALLATION
- OPERATION MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH P7100421 LED Par 64 COB 250W 5xWhite Mk2

INTRODUCTION

Thank you for purchasing LED PAR 64 COB 250W 5xWHITE Mk2. For safety reasons and to ensure a trouble-free operation, carefully read the instructions.

SAFETY INFORMATION

Installation should be done by qualified personnel in order to minimize the risk of accidental electric shock
Disconnect the power supply before installation.
Before connecting the unit to the mains, make sure it is not damaged mechanically. If you notice any signs of damage you should contact your dealer immediately. Do not connect the device to the mains.
Do not use the device in high humidity conditions and at temperatures above 40° C
The device must be installed on stable structures
Always use steel security cable to attach the device to a stable structure
Do not connect power supply to more than 4 devices in series.

PRODUCT INFORMATION

The device is equipped with high-quality, bright COB LED which consists of 5 rows of independently controlled LED chips with color temperatures of:

1900-2100K
3000-3200K
4000-4300K
5000-5500K
9000-10000K

Unique design, high quality and high durability make this device a great tool for both power users and those, who value simplicity and reliability.
The ergonomic double bracket (included) facilitates the use of the device in any condition. In order to expand the range of mounting options, the holder has an additional mounting holes.
The electronics is made of high-quality components and offers several features such as:

Features

2000K to 9000K color temperature (warm to cold white)
16-bit dimming resolution
Various dimming curves for smooth dimming in 8-bit mode
Dim delay (light bulb simulation)
Full DMX signal regeneration
Electronic protection against overheating
THEATRE or DISCO cooling volume modes.
Permanent color correction
Native support for optional wireless DMX module (optional)

Specification

Power consumption: 250W
Power supply voltage: 100 – 245V
Voltage frequency: 50/60Hz
Diode type: COB 5in1
Number of diodes: 1
Diode power: 250W
Display: LCD Matrix
Color: White: 2000K, 3000K, 4000K, 5000K, 9000K (smooth adjustment in the range of 2000-9000K)
Beam angle: 37°
Dimming: Linear: 0 – 100%
Number of DMX channels: 6 / 7 / 5 / 10
DMX standard: DMX 512
Control interface: 4 buttons
Operating modes: DMX512, Auto, Sound-controlled, Master / Slave, Manual color
Features: DMX Signal regeneration, Electronic protection against overheating
AC IN: powerCON
AC OUT: powerCON
DMX IN: XLR – 3 pin
DMX OUT: XLR – 3 pin
IP Rating: IP20
Housing made: ABS
Cooling: Active
Height [cm]: 30
Width [cm]: 27
Depth [cm]: 13
Weight [kg]: 3,6
Weight with packaging [kg]: 4,4
Set includes: Power cord, Double bracket, Barn Doors

Photometric data

FLASH P7100421 LED Par 64 COB 250W 5xWhite Mk2-1

INSTALLATION

After removing the packaging, check if the device was not damaged during transport. Before connecting to the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage caused by unstable mounting.

CAUTION! Always use steel security cable to attach the device to a stable structure.
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are consistent with device requirements. All activities, including connecting the device to the mains must be performed by qualified personnel.

CONNECTIONS
The device is equipped with the following interfaces:

DMX (in/out): XLR 3-pin socket
Power (in/out): powerCON socket

Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.

Voltage specification

Input Voltage	Total Power	Frequency
100~245V	250W	50/60Hz

Connecting power supply
The connection is performed using power cable with PowerCon connector (included).
The device must be operated by qualified personnel. Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.
Maximum number of devices connected in series: 4