BRANDMOTION 9002-2780 Dual Camera Interface Installation Guide
- June 13, 2024
- BRANDMOTION
Table of Contents
BRANDMOTION 9002-2780 Dual Camera Interface Installation Guide
INSTALLATION INSTRUCTIONS’
Dual Camera Interface for 4-inch “My Ford” factory display (Part #
9002-2780)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit
- 2780 v2 interface module
- USB cable (for updates)
- RCA input cable
- Plug & Play T-harness
Tools & Supplies Required
- 7mm socket
- Multi-meter or computer safe test light
- Wire Ties or Electrical Tape
- Plastic Trim Removal Tool
- Vehicle service manual (If needed)
Safety Precautions
- Work in a well-ventilated area that is clear of obstructions.
- Secure vehicle with tire chucks in both front and rear of tires.
- Turn vehicle accessories OFF and ensure ignition key is in OFF position.
- Wear safety goggles and snug fitting clothes.
- Use tools only for their intended purpose and which are in good repair.
- Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation
instructions.
For the latest full color instructions please visit
www.brandmotion.com
2780 v2 pin out:
SCREEN REMOVAL AND MODULE INSTALLATION
- Remove the 4” media screen from the dashboard, above the CD player.
- Connect the provided Plug & Play T-Harness to the OEM ford 12-pin plug previously connected to the radio.
- After installing and running your reverse camera to the dash opening, connect your RVC signal to the Yellow RCA found on the Plug & Play T-Harness. Power your camera with an ACC source (OUTPUT 1 provides 12v ACC @ 1 amp MAX).
- Connect the 2780 v2 module to the 18-pin harness on the Plug & Play T-Harness.
- Connect the male end of the Plug & Play T-Harness to the screen and proceed to the next section.
2780 PROGRAMMING AND TESTING:
Programming for the 9002-2780 v2 is automatic. After all connections are
properly made and the module is
connected, turn the car on to IGNITION, wait for the radio to fully boot and
settle before testing functionality.
NOTES:
- The radio may or may not visually reboot with a ‘Diagnosis’ message. It may appear that the radio just boots slowly (only the first time, in which case it took programming before the display appeared).
- Place the car into reverse, the screen should automatically display the connected reverse image (or a warning screen if you have no camera connected).
- This module VIN-LOCKS to the vehicle it is connected to and cannot be used on any other vehicle once installed
- This module will NOT de-program rear camera, once this modification is made to the system, it will remain forever!
- After all connections are made and programming is complete, placing the vehicle in reverse will automatically display the connected rear camera’s image.
- If forced rear camera is desired, connect input 1 (red) to 12v (+) through a toggle (not included) and the rear image will show whenever activated.
- If a front camera was added, force this camera by connecting input 2 (blue) to 12v (+) through a toggle (not included).
The reverse image will have rounded edges and the OEM radio screen showing behind the reverse image is OEM Ford operation and is normal.
Some vehicles may retain the reverse image while in drive until ~5 mph, this
is also normal Ford operation.
2780 INSTALLATION DIAGRAM
FORD 4-INCH SCREEN COMPATIBILITY
Due to the large variety of different 4” screen part numbers, it is strongly
advised to verify the screen compatibility by removing the screen and
measuring a 75-ohm termination across pins 6 and 12. Brandmotion cannot assure
compatibility unless this step has been taken.
POWERED BY:
Documents / Resources
|
BRANDMOTION 9002-2780 Dual Camera
Interface
[pdf] Installation Guide
9002-2780 Dual Camera Interface, 9002-2780, Dual Camera Interface, Camera
Interface
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>