RUGGED RIDGE 13264.01 Rear Seat Covers Instruction Manual

: June 13, 2024
: RUGGED RIDGE

Table of Contents

RUGGED RIDGE 13264.01 Rear Seat Covers
Product Information
Product Usage Instructions
Parts included
Instructions
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RUGGED RIDGE 13264.01 Rear Seat Covers

RUGGED-RIDGE-13264-01-Rear-Seat-Covers-PRODUCT

Product Information

Part	Quantity
Rear (top & bottom) Left Side Seat Cover – Small	1
Rear (top & bottom) Right Seat Cover – Large	1
Head Rest Covers	2

Note: Please read instructions before installing.

Product Usage Instructions

Step 1: Release and slightly fold rear seat forward – Driver Side. For 2008 and newer JK’s, pull the nylon seat release located on the bottom corner of the seat.
Step 2: Slip upper seat cover over the seat. Note the location of headrest slots with Velcro.
Step 3: Slip the lower Velcro strip between the upper and lower portions of the seat and secure.
Step 4: Secure the front and rear Velcro as shown. Adjust as needed.
Step 5: Pull upper seat sections through headrest slots. Note: Tilting the headrest back will help with installation. Secure front and rear Velcro flaps. (Note: on 2008 and newer models, the seat release is deleted from the top. Flip the supplied flap over the top of the seat and stuff it under the cover.)
Step 6: Slip the smaller lower seat cover into the bottom of the seat. Push the rear of the cover (with clips) between the top and bottom of the seat. Folding the seat forward will ease installation.
Step 7: With the front of the cover pulled over the seat, run nylon straps and clips under the seat. Secure to back clips and pull tight. (Note: DO NOT OVER TIGHTEN, damage to seat cover may result.)
Step 8: Slide side clips between seats and secure them to the underside of the seat.
Step 9: Repeat steps 6 – 8 for the right side lower seat.
Step 10: Unzip the large right side upper cover. Slip it around the seat as shown in steps 10A and 10B. The seat belt must be slid through the opening before zipping.
Step 11: Push lower Velcro flaps between the upper and lower seat and secure them together.
Step 12: Pull upper seat sections through headrest slots. Note: Tilting the headrest back will help with installation. Secure front and rear Velcro flaps. (Note: on 2008 and newer models, the seat release is deleted from the top. Flip the supplied flap over the top of the seat and stuff it under the cover.)
Step 13: Slide covers over headrests as shown.

Parts included

(1) Rear (top & bottom) Left Side Seat Cover – Small
(1) Rear (top & bottom) Right Seat Cover – Large
(2) Head Rest Covers

NOTE: Please read instructions before installing

Instructions

RUGGED-RIDGE-13264-01-Rear-Seat-Covers-FIG-1

Step (1)
- Release and slightly fold rear seat forward -Driver Side For 2008 and newer JK’s pull nylon seat release located on the bottom corner of the seat.
Step (2)
- Slip upper seat cover over seat. Note location of head rest slots with Velcro.
Step (3)
- Slip lower Velcro strip between the upper and lower portions of the seat. and secure.
Step (4)
- Secure front and rear Velcro As shown. Adjust as needed.
Step (5)
- Pull upper Seat sections through head rest slots.
- Note: Tilting head rest back will help with install. Secure front & rear Velcro flaps.
- Note: on 2008 and newer models the seat release is deleted from the top. Flip the supplied flap over the top of the seat and stuff under cover (5B)
Step (6)
- Slip smaller lower seat cover into bottom of seat. Push rear of cover (with clips) between top and bottom of seat. Folding seat forward will ease installation.
Step (7)
- With front of cover pulled over seat run nylon straps and clips under seat.
- Secure to back clips and pull tight.
- NOTE: DO NOT OVER TIGHTEN Damage to seat cover may result.
Step (8)
- Slide side clips between seats and secure to underside of seat.
Step (9)
- Repeat steps 6 – 8 for the right side lower seat.
Step (10)
- Unzip large right side upper cover. Slip around seat as Shown in steps 10A and 10B.
- Seat belt must be slid through opening before zipping.
Step (11)
- Push lower Velcro flaps between the upper and lower seat and secure together.
Step (12)
- Pull upper Seat sections through head rest slots.
- Note: Tilting head rest back will help with install. Secure front & rear Velcro flaps.
- Note: on 2008 and newer models the seat release is deleted from the top. Flip the supplied flap over the top of the seat and stuff under cover (12B)
Step (13)
- Slide covers over head rest as shown.