RUGGED RIDGE IS-NFSC-02 Neoprene Front Seat Covers Black Installation Guide

RUGGED RIDGE IS-NFSC-02 Neoprene Front Seat Covers Black

Product Information

Product Model: IS-NFSC-02
Compatible Models: 13214.01, 13214.09, 13214.53, 13215.01, 13215.09, 13215.53, 13215.04

Parts included:

1. Front driver’s side seat cover – with headrest
2. Front passenger’s side seat cover – with headrest

Product Usage Instructions

Please read all instructions carefully before you begin.

1. Step 1: Slide and tilt the back of the seat forward.
2. Step 2: Remove the headrest.
3. Step 3: Place the upper cover over the top of the seat. Pull it all the way down.
4. Step 4: The neoprene cover has two holes on top. Push the fabric down and under plastic headrest lock tabs mounted into the top of the seat.
5. Step 5: Fish the front flap through the gap between the upper and lower seat sections. This may be a tight fit. Folding the seat forward may help.
6. Step 6: Pull the rear flap tight and attach it to the front flap using the attached Velcro. Adjust the cover for a proper fit.
7. Step 7: Slip the side ABS airbag cover under the cover. Install the headrest cover and attach Velcro to secure it.
8. Step 8: Place the driver’s side lower cover onto the seat. Fish the rear buckles through the gap between the upper and lower seat. This may be a tight fit. Folding the seat forward may help.
9. Step 9: Attach the two side hooks to the underside of the seat. The hooks should be attached to a secure point under the seat.
10. Step 10: Slide the front and rear lower straps under the seat. Make sure that the front straps are inserted through the front seat adjuster arm to ensure proper operation of the seat slider. Connect the front clip to the rear clip and adjust. Do not over tighten.
11. Step 11: Install the headrest cover. Note: 2011 and newer headrest covers are longer on the backside and have a Velcro strap on the bottom to secure.
12. Step 12: Repeat steps 1-11 for the other side.

Parts included:

• (1) Front driver’s side seat cover – with headrest
• (1) Front passenger’s side seat cover – with headrest

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN

INSTALLATION

1. Step 1. Slide, and tilt back of seat forward.

2. Step 2. Remove the rest.

3. Step 3. Place upper cover over top of seat. Pull all the way down as shown.

4. Step 4. The neoprene cover has two holes located on top. Push the fabric down and under plastic headrest lock tabs mounted into top of seat

5. Step 5. Fish front flap through the gap between the upper and lower seat sections. This is a tight fit. Folding the seat forward may help.

6. Step 6. Pull the rear flap tight and attach to the front flap using the attached Velcro. Adjust the cover for proper fit.

7. Step 7. Side ABS air bag cover should slipped under cover as shown. Install head rest cover and attach velcro to secure.

8. Step 8. Place driver’s side lower cover onto seat. Fish rear buckles through gap between the upper and lower seat. This is a tight fit. Folding the seat forward

9. Step 9. Attach two side hooks to the underside of the seat. The hooks can be attached to and secure point under the seat.

10. Step 10. Slide front and rear lower straps under seat. Make sure that the front straps are inserted through the front seat adjuster arm to insure proper operation of seat slider. Connect front clip to rear clip and adjust. DO NOT OVER TIGHTEN!!!

11. Step 11. Install the headrest cover.
    Note : 2011 and newer headrest covers are longer on the back side and have a Velcro strap on the bottom to secure them.

12. Step 12. Repeat step 1-11 for other side.

460 HORIZON DR. SUITE 400
SUWANEE, GA 30024
PHONE : 770-614-6101
FAX : 770-614-6069 info@omix- ada.com
2007-Current Jeep® Wrangler JK-Neoprene Front Seat Covers 2-door and 4-door (front seats only)

References

• Health. Powered by Ada.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>