BLUE OX BX1149 2022 Jeep Grand Wagoneer Instruction Manual

BLUE OX BX1149 2022 Jeep Grand Wagoneer

Product Information

• The product is the BX1149 Baseplate designed for the 2022 Jeep Grand Wagoneer (No Tow Hooks) model. It is compatible with vehicles that include Adaptive Cruise Control, Turbo, and Shutters.
• The installation instructions provide information on the attachment tab height and width, as well as the bolt torque specifications for both inch and metric bolts. The manual also includes a warning regarding the importance of reading and following the instructions to prevent property damage, personal injury, or even death.
• The manual provides a reference to visit the website www.blueox.com for the latest version of the installation instructions. It also mentions contacting the company at (402)385-3051 if the front of the vehicle looks different.

Product Usage Instructions

Before installing or operating the BX1149 Baseplate, it is essential to read both the Installation Instructions and the General Information sheet.

1. Gather the necessary tools for installation, including a large vise grip, flat screwdriver, utility knife, Phillips screwdriver, torque wrench, and drill.
2. Refer to the provided diagram for item numbers and part numbers.
3. Identify and assemble the required components based on their respective part numbers.
4. Securely attach the baseplate to the designated areas on the vehicle, using the provided hex head bolts of appropriate sizes and grades.
5. Install the attachment tab assemblies with holes at the specified locations.
6. Mount the electrical bracket with the breakaway switch in the designated position using the provided support plate.
7. Ensure all components are properly tightened according to the specified torque values.
8. Connect the 4-pin and 6-pin connectors as indicated.
9. Complete the installation by securing the #10-32 1/2 round slotted head screws.
   For any variations in the vehicle’s appearance or for further assistance, contact Blue Ox at (402)385-3051. It is also recommended to consult the vehicle owner’s manual for the manufacturer’s towing specifications.

INTRODUCTION

Please read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.

1. Blue Ox® towing products and accessories are intended to be installed by Blue Ox® Dealers who are familiar with our products and have the equipment and knowledge necessary to do “fit work”. If needed, Blue Ox® Dealers can be found at www.blueox.com or by contacting our Technical Service Department at 402-385-3051.
2. Many Blue Ox® baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting. Always use the hardware supplied in the hardware kit and existing hardware as specified in the installation instructions.

Bolt Torque Specifications
Torque in Foot-Pounds for Inch Bolts

Bolt Torque Specifications
Torque in Foot-Pounds for Metric Bolts

Instruction Notes:

• The fascia and windshield washer fluid reservoir are removed and reinstalled for the baseplate installation. Some drilling and trimming is required.
• Place all components that are removed on a flat, sturdy surface. All items will be reinstalled unless otherwise noted after the baseplate is installed.
• The dimensional variations between otherwise identical vehicles can be considerable. While the baseplate was designed for easy installation, it may be necessary to tailor the baseplate slightly to compensate for vehicle manufacturer’s tolerances.
• A light bar is recommended for this vehicle.

NOTICE

• Handling of some cosmetic parts when installing this product may require the use of protective covers, rags, specialty tools, etc. to prevent damage.
• When using power drills be aware of the dangers of torque and drill bit length.
• When using a reciprocating saw be aware of objects behind the cutting surface.
• Use a good quality paint to spray cut edges of frame to prevent rusting.
• Be sure that ALL electrical connections are plugged in and accessories are functioning properly before reinstalling the fascia.
• The baseplate is computer tested to your vehicle’s GVWR, exceeding this weight will void the manufacturer’s warranty.
• Be sure to use a sufficient amount of Loctite® Red on all bolt threads before tightening. Tighten all bolts according to the torque chart provided unless specified.
• Dealer or installer be certain the user receives these instruction sheets.
• If the baseplate is in an accident, it must be replaced. DO NOT use it again! An accident can cause unseen damage and using it again could result in more damage or serious injury. DO NOT use the baseplate if it is damaged or missing parts.

PRODUCT OVERVIEW

Important:
Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered through your nearest Blue Ox® Dealer or Distributor. Failing to follow and/or altering these installation instructions in either installation or required equipment will void the manufacturer’s warranty. Towing behind a non-motorized vehicle will void the warranty.

INSTALLATION INSTRUCTION

1. Using an 8MM socket, remove the four (4) bolts from the wheel well edge. Do this on both sides of the vehicle.
2. Unsnap the wheel well trim past the fascia joint. Unplug light as trim is pulled back. Place soft cloth between trim and vehicle to hold trim out of the way. Do this on both sides of the vehicle.

3. Pull back the wheel well liner. Using a 10MM socket, remove the one (1) bolt from the fascia joint. Do this on both sides of the vehicle.
4. Using a 10MM socket, remove the three (3) bolts from the bottom of the fascia.

5. Remove fascia and set aside to be reinstalled later. Unplug the electrical on both sides of the vehicle and hose in the center as the fascia is removed.

6. Using a utility knife, trim plastic shroud as shown on both sides of the vehicle and remove piece.
7. Using a 18MM socket or wrench, remove the three (3) nuts from the bumper. Do this on both sides of the vehicle. Remove bumper, it will not be reinstalled.

8. Using a 10MM socket, remove the two (2) bolts (white) from the plastic piece on the bottom of the bumper. Then using 1/4” drill bit, drill out the four (4) plastic rivets (gray). Remove plastic piece and set aside to be reinstalled with the baseplate.
9. Using a 13MM socket, remove the five (5) nuts on the backside of the fascia. Remove foam piece and set aside. It will not be reinstalled.

10. Hold baseplate in place and start the three (3) 1/2” x 1-1/2” bolts with flat washers and nylon lock nuts. Snug up the baseplate into place but leave loose. Do this on both sides of the vehicle.
11. Attach cross member to baseplates, start the two (2) 3/8” x 1” bolts with flat washers and nylon lock washers. Do this on both sides of the vehicle. Ensure baseplate is level and tighten baseplate on each side then cross member.

12. Attach support bracket to baseplate using one (1) 1/2” x 1-1/2” bolt with flat washer and nylon lock nut. Do this on both sides of the vehicle.
    Use Loctite® Red on all bolt threads and tighten all bolts to the appropriate torque.

13. Using a 1/2” drill bit, drill the bottom inside hole on the front of the baseplate (left). Then using the support bracket as a template, drill 1/2” hole in frame (right). Do this on both sides of the vehicle.

14. Install one (1) 1/2” bolt with lock washer and whiz nut. Do this on both sides of the vehicle.
15. Install one (1) 1/2” x 1-1/2” bolt with flat washer and nylon lock nuts into the bottom inside hole on the front of the baseplate. Do this on both sides of the vehicle.
    Use Loctite® Red on all bolt threads and tighten all bolts to the appropriate torque.

16. Attach plastic piece from bumper to cross member using four (4) 1/4” x 1” bolts with flat washers and lock washers. Note: Grooves on plastic piece should be facing forward.
    Use Loctite® Red on all bolt threads and tighten all bolts to the appropriate torque.

17. Attach the permanent baseplate safety cables to the provided convenience link on the baseplate. The photo above shows the recommended installation of the cables to frame of vehicle. Additional options may interfere with suggested mounting; in this case, secure the cables to a solid piece of the frame as described in the General Information sheet. Be sure the safety cables do not rub against any hoses or moving parts. Do this on BOTH sides of the vehicle.

18. Hold the fascia as close to its original position, mark and trim the fascia around the convenience links and attachment tabs. Reinstall the fascia and reconnect all electrical and hose.

CUSTOMER SERVICE COMMITMENT

• Blue Ox® is committed to providing you with exceptional customer care throughout your lifetime with our products. Our team is here to assist you with any questions you may have regarding the performance of your product. Simply call 402-385-3051 and you can speak with our technical service team.
• Additionally, please visit our website to see which rallies our Destination America team will be attending. For a nominal fee, our service technician will service your towing system to ensure it’s in proper working condition. Also, as a commitment to our customers, should you visit our factory, you can stay at our full service Blue Ox® campground at no charge along with enjoying a factory tour.
• Again, thank you for being our customer and for the confidence you have shown in the performance of our products. It is because of customers like you we enjoy the success we have today.

General Information

1. Ensure that your product(s) are registered online at www.blueox.com. It is crucial to register your product(s) so that you may be alerted of product offerings, updates, upgrades, maintenance and safety bulletins, and/ or recalls.
2. It is the owner’s responsibility to inspect all towing equipment for cracked welds, missing or worn parts and loose bolts before each towing trip. Be sure to use Loctite® Red on all bolts and tighten to the recommended specifications.
3. It is the owner’s responsibility to hook up all towing equipment per manufacturer’s instructions/ recommendations.
4. Remove the attachment tabs when not in use (if applicable).

Notice To Baseplate Installer

It is YOUR responsibility to watch for:

• Oil cooler and air conditioner lines
• Electrical wires and hoses
• Missing parts or attaching points on the frame
  If the baseplate is improperly installed and is against a wire or hose, it could cause fluid leaks or electrical shorts some time after the actual baseplate installation.

Permanent Baseplate Safety Cable Installation

• Permanent baseplate safety cables are strongly recommended when towing a vehicle with a tow bar.
• The principle function of the permanent baseplate safety cables is to prevent the towed vehicle from breaking loose in the event the connection between the frame of the towed vehicle and the baseplate fails or becomes disconnected. The cables must be connected from the baseplate to the frame rail or cross member of the vehicle’s frame. The illustrations below show the possible arrangements recommended by Blue Ox®. Each permanent baseplate safety cable must have an adequate weight rating for the towing system. The weight rating of the two (2) cables together will not qualify.
• Do not mount the permanent baseplate safety cables against wires, hoses or brake lines.
• These permanent baseplate safety cables should remain installed as long as the baseplate is installed on the vehicle. Permanent baseplate safety cables are to be used in conjunction with, and NOT a replacement for legally required safety cables attaching the towed vehicle to the towing vehicle.

BLUE OX ORIGINAL PURCHASERS THREE YEAR LIMITED WARRANTY

• Automatic Equipment Manufacturing Company (“Automatic”) warrants to the original (first) retail purchaser that this product, manufactured by Automatic, shall be free from defect in material and workmanship under normal use and service for a period of three years from the date of delivery.

• During said three-year period, Automatic will repair or replace any parts that have been returned by the original purchaser, to the factory, transportation prepaid, and in Automatic’s sole and absolute opinion found to be defective.

• Limitations on Warranty Coverage:

• Coverage under this warranty will be valid only if the customer warranty card is returned by the original purchaser within 30 days of purchase.

• Coverage under this warranty will be effective only when a copy of the original invoice, showing date and place of purchase, accompanies any claim for warranty. This warranty is NON TRANSFERABLE.
  This limited warranty will not cover, in any way or form, any alleged damages caused by incorrect or improper installation, improper use, modification or neglect of product, failure to properly service and maintain, misuse, act of God, accident or failure of the user to follow guidelines contained in the instructional material provided by Automatic.

• This warranty does not cover normal wear and tear, paint or rust.
  Warrantor assumes no responsibility to the owner for loss of use of product, loss of time, inconvenience or any other damage consequential or otherwise. Including, but not limited to mileage, expense of transporting of product, return shipping expense, mechanics travel time, telephone, road service, towing, and rental during repairs, travel, lodging, loss or damage to personal property or loss of earnings.

• REPAIR OR REPLACEMENT AS SET FORTH IN THIS LIMITED WARRANTY IS THE SOLE EXCLUSIVE REMEDY OF THE PURCHASER. AUTOMATIC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN LENGTH TO THE DURATION OF THIS WARRANTY.

• Please visit http://blueox.com/warranty/ to register your warranty

References

• Blue Ox Product Warranty Registration - Blue Ox
• Home - Blue Ox

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>