RUGGED RIDGE JK 2011-2018 Dash Multi Mount System With Charger Installation Guide
- June 13, 2024
- RUGGED RIDGE
Table of Contents
RUGGED RIDGE JK 2011-2018 Dash Multi Mount System With Charger
FCC Part 18 Compliance Statement for Wireless Charger
This equipment has been tested and found to comply with the limits for a WPC
device, pursuant to Part 18 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Increase the separation between the equipment and the receiver.
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Information to the user
-
Do not disassemble or throw into fire or water, to avoid damage.
-
Do not use wireless charger in severely hot, humid or corrosive environments, to avoid circuit damage and occurs leakage phenomenon.
-
Do not place too close with magnetic stripe or chip card (ID card, credit cards, etc.) to avoid magnetic failure.
-
Please keep the distance of at least 30cm between implantable
medical devices (pacemakers, implantable cochlear, etc.) and the wireless charger, to avoid potential interference with the medical device. -
Take care of children, to ensure that they won’t play the wireless charger as a toy.
-
Some phone case may affect the charging performance. Ensure there is no any metal object between your phone cases or try to take it off before charging.
-
Device should not be installed near maritime safety communications equipment or other critical navigation or communication equipment.
Specification
Input : DC 5V-2A, DC9V-1.67A
Output : 10W Max
Frequency range: 0.15 MHz – 30MHz
Color : Black
Components
- Mult-Mount Tray……………………………………………………………… 1
- Wireless Charging Phone Mount …………………………………….. 1
- USB Charging Cord ………………………………………………………… 1
- Dual USB Charging Port…………………………………………………..
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am – 5pm EST 1-800-449-6649
FOR WARRANTY OR TECH CONCERNS EMAIL:
webmaster@omixsupport.com
ATTN: STATE OF CALIFORNIA CONSUMERS
WARNING: Cancer and Reproductive Harm –www.P65Warnings.ca.gov.
MOUNTING INSTRUCTIONS
Step 1
Remove factory rubber tray from dashboard storage area above center console.
Remove factory screw using a socket driver and a 7 mm socket. Do not discard
factory screw, it will be reused in product installation
Step 2
Install Accessory Mount Base. Hooks on arms of Accessory Mount Base will snap
into upper dashboard vents closest to windshield. Reinstall factory screw
removed in Step 1.
Place custom Rubber Tray into dashboard storage area.
Step 3
The Ball mount should be attached to your accessory mount base. If it isn’t
then attached with provided hardware as shown
Step 4
Place outer ring over end of ball mount.
Step 5
Press phone mount into ball mount.
Note: Image shown here is the non-charging base, the charging base mounts
in the same manner.
Step 6
Pull outer ring over phone mount adapter and thread tightly to secure.
Step 7
Route power cord from charging base to a USB power port. If you choose to use
the powered duel USB port provided then install in a precut switch pod or cut
a provision to install. When wiring power to the USB port make sure to include
in-line fuse.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>