RUGGED RIDGE 13551.35 Dash Multi Mount System with Charger Installation Guide
- June 13, 2024
- RUGGED RIDGE
Table of Contents
RUGGED RIDGE 13551.35 Dash Multi Mount System with Charger
Rugged Ridge Dash Multi Mount System with Charger, JL
Part #13551.35
Product Information:
- The Rugged Ridge Dash Multi Mount System with Charger, JL is a versatile mounting system designed for use in vehicles.
- It includes a wireless charging phone mount, a multi-mount tray, a USB charging cord, and a dual USB charging port.
- The input voltage is DC 5V-2A and DC9V-1.67A, while the output is up to 10W.
- The frequency range is from 0.15 MHz to 30MHz.
- The color of the product is black.
Product Usage Instructions
- Before installing the Rugged Ridge Dash Multi Mount System, follow these steps:
- Step 1: Remove the interior rubber liner by prying a corner to lift it.
- Step 2: Remove the two Phillips screws from inside the compartment.
- Step 3: Ensure the installation area is completely clean.
- To install the Rugged Ridge Dash Multi Mount System:
- Step 4: Place the Multi-Mount System into position.
- Step 5: Reinstall the Phillips screws removed in Step 2 through the multi-mount system into the dash.
- To mount your phone on the charging base:
- Step 6: Place the outer ring over the end of the ball mount.
- Step 7: Press the phone mount into the ball mount. Note: The image shown is for the non-charging base, but the charging base mounts in the same manner.
- Step 8: Pull the outer ring over the phone mount adapter and thread it tightly to secure.
Rugged Ridge Dash Multi Mount System with Charger, JL
FCC STATEMENT
FCC Part 18 Compliance Statement for Wireless Charger.
This equipment has been tested and found to comply with the limits for a WPC
device, pursuant to Part 18 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or nore of the following measures:
- Increase the separation between the eauipment and the receiver.
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Information to the user
- Do not disassemble or throw into fire or water, to avoid damage.
- Do not use wireless charger in severely hot, humid or corrosive environments, to avoid circuit damage and occurs leakage phenomenon.
- Do not place too close with magnetic stripe or chip card (ID card, credit cards, etc.) to avoid magnetic failure.
- Please keep the distance of at least 30cm between implantable medical devices (pacemakers, implantable cochlear, etc.) and the wireless charger, to avoid potential interference with the medical device.
- Take care of children, to ensure that they won’t play the wireless charger as a toy.
- Some phone case may affect the charging performance. Ensure there is no any metal object between your phone cases or try to take it off before charging.
- Device should not be installed near maritime safety communications equipment or other critical navigation or communication equipment.
Specification
- Input: DC 5V-2A, DC9V-1.67A
- Output: 10W Max
- Frequency range: 0.15 MHz – 30MHz
- Color: Black
Components
- Mult-Mount Tray………………………………………………………………. 1
- Wireless Charging Phone Mount……………………………………… 1
- USB Charging Cord…………………………………………………………. 1
- Dual USB Charging Port…………………………………………………… 1
INSTRUCTION
Step 1
Remove interior rubber liner. May need to pry a corner to lift.
Step 2
Remove two Phillips screws from inside compartment.
Step 3
Place Multi-Mount System into position. Assure area is completely clean before
installing.
Step 4
Reinstall Phillips screws removed from step 2 through multi-mount system into
the dash.
Step 5
Place outer ring over end of ball mount.
Step 6
Press phone mount into ball mount.
Note: Image shown here is the non-charging base, the charging base mounts
in the same manner.
Step 7
Pull outer ring over phone mount adapter and thread tightly to secure.
Step 8
Route power cord from charging base to the USB power port located at the lower
right of your center console. If you would rather choose to use the powered
duel USB port provided then install in a precut switch pod or cut a provision
to install. When wiring power to the USB port make sure to include in-line
fuse.
Copyright © 2019 Omix-Ada®, Inc.
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am – 5pm EST
1-800-449-6649
FOR WARRANTY OR TECH CONCERNS EMAIL:
webmaster@omixsupport.com
ATTN: STATE OF CALIFORNIA CONSUMERS
WARNING: Cancer and Reproductive Harm –
www.65Warnings.ca.gov.
Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR.
SUWANEE, GA 30024
PHONE: 770-614-6101
FAX: 844-270-0593
www.Omix-ADA.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>