RUGGED RIDGE JK 2007-2010 Dash Multi Mount System with Charger Installation Guide

RUGGED RIDGE JK 2007-2010 Dash Multi Mount System with Charger

Rugged Ridge Dash Multi Mount System with Charger, JK 2007-2010

• Part Number: 13551.33
• Manufacturer: Omix-ADA
• Address: 460 Horizon Dr., Suwanee, GA 30024
• Phone: 770-614-6101
• Fax: 844-270-0593
• Website: www.Omix-ADA.com

Components:

1. Multi-Mount Tray – Quantity: 1
2. Wireless Charging Phone Mount – Quantity: 1
3. USB Charging Cord – Quantity: 1
4. Dual USB Charging Port – Quantity: 1

Product Usage Instructions:

1. Step 1: Remove the factory dash cover above the center console. Unscrew the remote compass module from the factory dash. Use screws to reattach the remote compass module to the Multi-Mount Dash Storage.
2. Step 2: Install the Multi-Mount Dash Storage by snapping the front lip into the dash, then pressing the back tabs into place.
3. Step 3: The Ball mount should already be attached to your accessory mount base. If it isn’t, attach it using the provided hardware as shown.
4. Step 4: Place the outer ring over the end of the ball mount.
5. Step 5: Press the phone mount into the ball mount. Note: The image shown here is the non-charging base, but the charging base mounts in the same manner.
6. Step 6: Pull the outer ring over the phone mount adapter and thread it tightly to secure.
7. Step 7: Route the power cord from the charging base to a USB power port. If you choose to use the provided powered dual USB port, then install it in a precut switch pod or cut a provision to install. When wiring power to the USB port, make sure to include an in-line fuse.

Rugged Ridge Dash Multi-Mount System with Charger, JK 2007-2010

FCC STATEMENT

FCC Part 18 Compliance Statement for Wireless Charger.
This equipment has been tested and found to comply with the limits for a WPC device, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Increase the separation between the equipment and the receiver.
2. Reorient or relocate the receiving antenna.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Information to the user:

1. Do not disassemble or throw into fire or water, to avoid damage.
2. Do not use wireless charger in severely hot, humid or corrosive environments, to avoid circuit damage and occurs leakage phenomenon.
3. Do not place too close with magnetic stripe or chip card (ID card, credit cards, etc.) to avoid magnetic failure.
4. Please keep the distance of at least 30cm between implantable medical devices (pacemakers, implantable cochlear, etc.) and the wireless charger, to avoid potential interference with the medical device.
5. Take care of children, to ensure that they won’t play the wireless charger as a toy.
6. Some phone case may affect the charging performance. Ensure there is no any metal object between your phone cases or try to take it off before charging.
7. Device should not be installed near maritime safety communications equipment or other critical navigation or communication equipment.

Specification

• Input : DC 5V-2A, DC9V-1.67A
• Output : 10W Max
• Frequency range: 0.15 MHz – 30MHz
• Color : Black

Components

1. Mult-Mount Tray……………………………………………………………… 1
2. Wireless Charging Phone Mount …………………………………….. 1
3. USB Charging Cord ………………………………………………………… 1
4. Dual USB Charging Port………………………………………………….. 1

INSTRUCTION

Step 1
Remove factory dash cover above center console.
Unscrew remote compass module from factory dash.
Use screws to reattach remote compass module to Multi-Mount Dash Storage.

Step 2
Install Multi-Mount Dash Storage by snapping front lip into dash, then pressing back tabs into place.

Step 3
The Ball mount should be attached to your accessory mount base. If it isn’t then attached with provided hardware as shown.

Step 4
Place outer ring over end of ball mount.

Step 5
Press phone mount into ball mount.
Note: Image shown here is the non-charging base,the charging base mounts in the same manner.

Step 6
Pull outer ring over phone mount adapter and thread tightly to secure.

Step 7
Route power cord from charging base to a USB power port. If you choose to use the powered duel USB port provided then install in a precut switch pod or cut a provision to install. When wiring power to the USB port make sure to include in-line fuse.

Copyright © 2019 Omix-Ada®, Inc.

OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am – 5pm EST 1-800-449-6649
FOR WARRANTY OR TECH CONCERNS EMAIL: webmaster@omixsupport.com

ATTN: STATE OF CALIFORNIA CONSUMERS
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov.
Copyright © 2019 Omix-Ada®, Inc.

460 HORIZON DR.
SUWANEE, GA 30024
PHONE: 770-614-6101
FAX: 844-270-0593
www.Omix-ADA.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>