lowes 2023 4ft Euro Black Steel Yard Fence Panel Installation Guide
- June 13, 2024
- lowes
Table of Contents
lowes 2023 4ft Euro Black Steel Yard Fence Panel
Note: Clamps and Hardware are inside posts. Remove parts from the bottom of post.
Required Tools for Euro System Install
Hammer, tape measure, chalk or marker, shovel, post hole digger, wheel barrow,
adjustable wrench, M8 hex key, hack saw, rotary cutting tool or bolt cutting
tool, electric drill, 1/16 in., 5/16 in. & 3/8 in. drill bits.
Masonry drill bits, anchors and additional hardware may be needed to install
flange post.
Install Posts
Use in-ground post when installing in ground with concrete.
Use flange post when surface mounting on concrete or wood.
Measure Gate Opening
Posts for the gate opening must be set 48 In. apart measured from center of
post to center of post or 46 In. from Inside edge to edge. Posts must be
plumb. Let the posts cure before you Install panels.
Post Offset
Set the remaining posts at 72 In. on center or 70 In. Inside edge to Inside
edge.
Shorter spans must be in 1-7/8 ln. intervals. See Step 7for panel cutting.
Washers are used when panel is mounted to one side only.
Install First Panel
Mount Panel to post with clamps, nuts and bolts.
Continue Installing Panels
Mount 2 panels- Bolt through clamps on both sides of the post.
Corner Installation
Mount panel to comer post. Holes must be drilled In the post to mount a panel
at a 9QO angle corner.
Dimples mark the spot to drill.
NOTE : Flip the clip with the tab up on the side of the post that has
been drilled. This will keep the fence panels in line and level.
CutPanel
If you are going to install a span less than 6ft. The panel must be cut in
1-7/8 in. increments ending with a vertical wire.
Panel can be cut with a rotary cutting tool, hack saw or bolt cutting tool.
Caution: Use safety eye protection.
Caution: Cut edge may be sharp
Installing Acute Angle Corners
If you want to install a corner that is less than a 90″corneryou must measure
the post placement from the face or the corner post, 70 in. between inside of
posts.
You will have to mount the panel In the same fashion as shown In Step 6. Post
must be drilled for this Installation.
Installing Obtuse Angle Corners
If you want to install a comer that is greater than a 90″ comer you must
measure the post placement from the side or the corner post, 70 in. between
inside of posts. You will have to mount the panel in the same fashion as if
you were mounting panel in a straight line, not like a corner install.
Note: Installation with multiple non 900 angles may require panel orientation
to be reversed.
Gate Install
Start the gate lnstallatlon by mounting post side of hinge system.
Mark the holes by holdlng the top hinge 8.75 In. from cap and bottom hinge
38.25 from to cap. Be sure to measure from the bottom of caQ to the bottom of
the hinge. Drill 5/16 in. holes In post. Next mount gate side of hinge Into
existing holes In gate. Mount the bottom post hinge on the post with nutsand
bolts. Get the parts together to mount the top hinge. Install gate by hooking
the bottom gate side hinge Into the bottom post hinge. Next hook the top post
hinge onto the top gate side hinge, then while hinge Is together bolt assembly
together.
Latch Install
Pre-drlll 1/16 in. pilot holes on gate and mount striker to gate at desired
height with included self-tapping screws. Next line up latch on post, drill
and mount with self-tapping screws.
Stepped Installation/Grade
This fence is designed for use on flat ground. To deal with a slight grade, a
stepped installation is recomended. This is achived by setting the posts at a
taller installed height. It is not recomended to exceed +Sin. Installed post
maximum height 54-1/2 in.
Note: Flange posts can not be used for grade installations.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>