RUGGED RIDGE 11585.04 Accessory Brake Light LED Ring Installation Guide

RUGGED RIDGE 11585.04 Accessory Brake Light LED Ring

Product Information

The Accessory Brake Light LED Ring is a patented pending product manufactured by Omix-Ada. The part number for this accessory is 11585.04. It is designed to be installed on vehicles, specifically the Jeep Wrangler models. Please note that the LED Ring is not a
DOT approved third brake light, so it is important to check with state and federal ordinances regarding third brake light use before installation.

Product Usage Instructions

1. Remove the spare tire from the vehicle. It is recommended to have another person assist in lifting the tire off the tire mount.
2. Attach the Accessory Brake Light to the spare tire mount by sliding it over the wheel studs.
3. If installing on a 2007 to 2017 Wrangler, proceed to Step 3. If installing on an earlier model, skip to Step 7.
4. Open the tailgate and use a T-20 Torx bit to remove the four screws attaching the third brake light to the factory tire mount.
5. Pull the third brake light away from the tire mount and remove the electrical connector by depressing the tab. Set the third brake light aside for later use.
6. Connect the Accessory Brake Light plug to the factory’s third brake light harness.
7. If installing on a 2007 to 2017 Wrangler, reattach the factory third brake light to the tire mount. Skip to Step 10.
8. Disconnect the battery by removing the negative terminal first, then the positive terminal. Unsheathe the factory’s third brake light wires and cut and strip both ends.
9. Cut the Accessory Brake Light plug three inches from the end and strip the wires on the Accessory Brake Light.
10. Using the supplied butt connectors, splice the factory third brake light and Accessory Brake Light wires in one end and the factory wiring in the other end. Reconnect the battery.
11. Install the spare tire and torque the lug nuts to factory specifications. Depress the brake pedal and check for brake light functionality.

When performing any steps that require lifting the tire or removing battery cables, it is important to exercise caution and have another person assist if necessary. Failure to tighten the lug nuts to the proper torque specification could result in serious injury or property damage.

INSTALLATION INSTRUCTION

1. Remove the spare tire.
   • CAUTION
   • Have another person help lift the tire off the tire mount.
2. Attach the Accessory Brake Light to the spare tire mount by sliding over the wheel studs.
   • NOTICE
   • Proceed to Step 3 if installing on 2007 to 2017 Wrangler.
   • Skip to Step 7 if installing on the earlier model.
3. Open tailgate. Using the T-20 Torx bit, remove four screws attaching the third brake light to the factory tire mount.
4. Pull the third brake light away from the tire mount. Remove the electrical connector by depressing the tab. Set the third brake light aside to be used again.
5. Connect Accessory Brake Light plug to factory third brake light harness.
   • WARNING
   • LED Ring is not a DOT-approved third brake light. Check with state and federal ordinances regarding third brake light use.
6. Reattach the factory’s third brake light to the tire mount.
   • NOTICE Skip to Step 10 if installing on 2007 to 2017 Wrangler.
7. Disconnect the battery by removing the negative terminal first, then positive. Unsheathe factory third brake light wires. Cut and strip both ends.
   • WARNING
   • When removing battery cables do not touch positive and negative terminals together.
8. Cut the Accessory Brake Light plug three inches from the end and strip the wires on the Accessory Brake Light.
9. Using supplied butt connectors, splice the factory third brake light and Accessory Brake Light in one end and factory wiring in the other end. Reconnect battery.
10. Install spare tire and torque lug nuts to factory specification. Depress the brake pedal and check for brake light functionality.

CAUTION

Have another person help lift the tire on the tire mount.

WARNING Failure to tighten lug nuts to proper torque specification could result in serious injury or property damage.

• 460 HORIZON DR. SUITE 400
  

• SUWANEE, GA 30024
  

• PHONE:770-614-6101
  

• FAX:770-614-6069
  

• info@omix-ada.com

• FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com

References

• Health. Powered by Ada.
• OMIX Jeep Replacement Parts - OEM & Vintage Aftermarket Jeep Parts | Omix

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>