VEVOR 671020 30 Gallon Caddy Owner’s Manual
- June 13, 2024
- VEVOR
Table of Contents
30/35 Gallon Caddy
OWNER’S MANUAL
671020 30 Gallon Caddy
****WARNING CAUTION
Read carefully and understand alli ASSEMBLY AND/OR OPERATION INSTRUCTION
before using the product. Failure to follow the safety rules and other basic
safety precautions may result in serious personal injury.
Thank you for purchasing our product
This manual covers operation and maintenance information about the product.
Read carefully and understand allinstruction before using the product
All information in this publication is based on the latest product information
available ar the fime of appraval for printing.
We reserve the right te make changes a any time with out notice and without
any obligatian.
IMPORTANT SAFETY INSTRUCTION
READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICIN G
Wihen using this product, basic precautions should always be foliowed,
including the foliowing:
- This product is not intended forwse by persons lincluding chilarentwith reduced physical, sensory or mental capabilities or lack of experience and knowledge,uriess they have baen given supervision ar ingtruction concerning using the product by a parson responsible of thes safery
- Do not use this praduct other than intended use
- Wear proper protection equipment when installing or using this product.
- Ensure all fittings and threaded connections are thghtened and leak free before operating
DANGER!
Gasoline and other fuels are extremely flammable Keep away from heat sparks. and open flame.
- Do not use electronics or mobile communications devices such as mobile phones when pumping flammable liquids.
- Attach graund wire and bond containers that are Reing pump fram and inte. Ground al cantainers To a known ground source to dissipate static alectricity before pum ping liquids
- Attach graund wreand bond containers that are Being pump fram and inte. Grownd all cankainers To a known ground source to dissipate static alectrciry before pum ping liquids
- Gascline vapors can éxpode Harmful or fatal if swallowed Avoid breath in fuel vapors
- Do not smoke near or while wsing the gas caddy
- This product is intended for fuel transfer only and ismotintended to be used to transport fuelin any vehicle gr beaver
- Do not modify this product.
WARNING! CAUTION: ATTENTION!
- Do not use this product for proplonged fuel storage.
- Use caddy for one type of fuel only to avoid possible damage.
- Meniter flow rate and fill evel to orevent averfiaws and spills
- Alwaysemply the pump and hese aherusing the caddy Lift thea hase and turn the handle to the opposite direction to empty allremaining liquid back inte the caddy.
- Cautian when filing the cadde throught the fiiltube. Manitar clesety to prevent overflows ar spills
Before use, the ground clip needs to be high in the conductive position of the link ground
PARTS AND FEATURES
A.Ground wire
B. Hand pump
C. Oil outlet port
0. Hand pump handle
E Handle screw
F. Tubing clip
G. Olt filler pipe
H. Refueling filter
I. Thread seaiant
J. Oil outlet pipe
K. Refueling filter
L. Tank cap
M. Smail whee
N. Big wheel
O. Axle sleeve
P. Big whee! mounting screw
Q Sush handie
R. Push hand gasket
S. Push screw
T. Oil level probe
U. Oillevei gauge
V Oil level haing nye
W. Probe fixing caver
X. Frontleg of of: tank
Tools required for menstallatian
A, ground wire: 10mm wrench
C. oil pipe interface: 26 mm wrench
S. Handrail screw: 17mm wrench
P, big wheel screw: 19mm wrench
M,X feet, small wheel nut: 14mm wrench
ASSENMLY GUIDE
STP 1
Insert the wheel axle (0) to the caddy. Secure the axle in place with
washers(B).
STP
2
Pur the Metal wheel to the end of the wheel axle. Secure it in place with
washer (B) and cap nut [A)
Repeat the same step for the other wheel.
STP 3
Tilt the cadde an its side Rermove tha hesbut attached at the bottom af the
cadcy. Attach the foat (P1 its place and secure by tightening the removed
nut.
STP 4
Screw the oi! pump an {Q) the nume pine. Make sure they are aligned before
screwing ta prevent cross treading
STP 5
Attach the pump handle (5) to the cal pump. Please must be in correct
gestion belove teming to aviod to demage thread STP 6
Screw pump connector (¥| ta the oil pump Careful to prevert cross threading,
STP 7
Attach the wired tube (1) to the pump connector, Secure it in place by
tightering the hase clamp(U).
STP 8
Screw the tue: measure gauge (K) to the gas caddy and tighten the piastic
nut (L)
STP 9
Insert the ail fister (M) into the oi! inlet then cover it with the fuse:
cap (l)
STP 10
Attach the handle (W) te the caddy Secure itin place with nex colts
(E},washer(O},and hex nut (C}.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>