TRUCK HARDWARE 2022 F-150 Lightning Mud Flap Set Front Instruction Manual

TRUCK HARDWARE 2022 F-150 Lightning Mud Flap Set Front

Product Information

The 2022 Ford F-150 Lightning Mud Flap Set is designed to provide protection for your vehicle’s exterior by preventing mud, dirt, and debris from splashing onto the body. The set includes front and rear mud flaps, along with brackets and all necessary hardware for installation. Please note that the manufacturer is not responsible for any damage caused by negligent use of the mud flaps or over-tightening of screws and bolts.

Front Mounting Diagram & Instructions
The front mounting diagram and instructions provide step-by-step guidance on how to install the mud flaps on the front wheels of your Ford F-150 Lightning. The set includes two front flaps, two front brackets, and a parts bag containing various screws, washers, and nuts.

Tools Required

• Push Pin Removal Tool
• 7/16 Open Wrench and Socket Wrench
• 1/4 Open Wrench or Socket Wrench
• 10mm Open Wrench or Socket Wrench

Parts Included

• (1) Protective Tape Part#769914
• (1) Flap Front, DS
• (1) Flap Front, PS
• (1) Bracket Front, DS Part #769803
• (1) Bracket Front, PS Part #769804
• PARTS BAG #769808 containing various screws, washers, and nuts

Installation Instructions

1. Before installation, refer to the provided diagram and parts list to ensure you have all the necessary components.
2. Remove the two factory screws from the factory guard in the wheel well.
3. Remove the push pin from the underside of the guard.
4. Follow the provided diagrams and instructions to attach the mud flaps and brackets using the specified screws, washers, and nuts.
5. For ease of installation, it is suggested to remove the wheel.
6. Secure mud flap holes #8 & #9 to factory holes #5 & #6 using a sheet metal screw and flat washer.
7. Install mud flap hole #7 to bracket hole #7 using a capscrew, flat washer, nylon washer, and washer strip.
8. Refer to the provided diagram for additional installation steps.
9. For a visual guide, check out our YouTube channel for an installation video specific to this application.

Rear Mounting Diagram & Instructions
The rear mounting diagram and instructions provide step-by-step guidance on how to install the mud flaps on the rear wheels of your Ford F-150 Lightning. The set includes two rear flaps, two rear brackets, and a parts bag containing various screws, washers, and nuts.

Tools Required

• Push Pin Removal Tool
• 7/16 Open Wrench and Socket Wrench
• 1/4 Open Wrench or Socket Wrench

Parts Included

• (1) Flap Rear, DS
• (1) Flap Rear, PS
• (1) Bracket Rear, DS Part# 770603
• (1) Bracket Rear, PS Part# 770604
• PARTS BAG #770531 containing various screws, washers, and nuts

Installation Instructions

1. Before installation, refer to the provided diagram and parts list to ensure you have all the necessary components.
2. Hold up your mudflap and align the three lower mudflap holes with the three lower factory holes on the fender.
3. Mark the fender for drilling holes.
4. Follow the provided diagrams and instructions to attach the mud flaps and brackets using the specified screws, washers, and nuts.
5. For ease of installation, it is suggested to remove the wheel.
6. Refer to the provided diagram for additional installation steps.

Please note that proper installation and maintenance of the mud flaps are essential for optimal performance and longevity. Follow all instructions carefully to ensure a secure and effective installation.

Models GCR411F

IMPORTANT:
The manufacturer is not responsible for negligent use of a vehicle with mud flaps installed, including over-tightening of screws and bolts causing damage to the vehicle or mud flaps.

TOOLS REQUIRED

FLAPS AND BRACKETS

PARTS BAG

PARTS BAG # 769808

INSTALLATION

(For ease of installation it is suggested that the wheel be removed)

1. Before you install your Mud Flap Set, see the diagram and parts list for all necessary parts.
2. Remove the two factory screws from the factory guard in the wheel well.
3. Remove the push pin from the underside of the guard. This push pin is holding the portion of the guard protecting the push pin. It may be difficult to remove from the side facing you. We suggest going between the guard and the pinch weld to separate them so that you can push out the push pin from behind.
4. Once the push pin is removed, reinstall the guard into position with the existing tab.
5. Install capscrew (c) through a nylon washer (j) into factory hole #1 and insert a half washer (l) and bracket hole # 3 onto the protruding part of the screw, ensuring that bracket hole #2 is installed on factory bolt (see Diagrams #1 & #2).
6. Secure bracket hole #2 to the factory bolt using a nylon washer (k), flat washer (h), lock washer (m), and M6-1 hex nut (p) (See Diagram #2).
7. Secure bracket hole #3 to capscrew (c) using a nylon washer (k), flat washer (h), lock washer (m), and hex nut (n) (See Diagram #2).
8. Secure mud flap holes #8 & #9 to factory holes #5 & #6 using a sheet metal screw (d) and flat washer (g).
9. Install mud flap hole #7 to bracket hole #7 using a capscrew (b), flat washer (e), nylon washer (i), and washer strip (r), and secure with a nylon washer (i), flat washer (f), lock washer (m) and hex nut (n).
   • Note: Be sure to install the washer strip at approximately the 2:00 position so that it puts pressure on the upper section to prevent debris from falling behind the mudflap (See Diagram #3 for washer strip position).
10. Using a square or bubble level, ensure that the mud flap is level. Tighten all fasteners.
11. Clean the upper section of the wheel well with alcohol to prepare for protective tape.
12. Hold the upper section of the mud flap tight against the wheel well. Using a marker, make a small mark on the fender through mudflap holes #10 & #11 to determine where to install the spring nuts (q).
13. Pull the mudflap away from the fender and install/center the 3M tape protectors where you have marked your spring nuts (q) to be installed.
14. Install the spring nuts (q) with the extruding end facing out over the 3M tape protectors.
15. Secure mudflap holes #10 & #11 to spring nuts (q) using a capscrew (a) and flat washer (e)

Please check out our YouTube channel to see an install video for this application.

Models GCR411R

IMPORTANT:
The manufacturer is not responsible for negligent use of a vehicle with mud flaps installed, including over-tightening of screws and bolts causing damage to the vehicle or mud flaps.

TOOLS REQUIRED

FLAPS AND BRACKETS

PARTS BAG

PARTS BAG # 770531

INSTALLATION

(For ease of installation it is suggested that the wheel be removed)

1. Before you install your Mud Flap Set, see the diagram and parts list for all necessary parts.
2. Hold up your mudflap aligning the three lower mud flap holes with the three lower factory holes and mark the fender through the upper mud two flap holes to indicate where the protective tape (l) and spring nuts (i) will be installed.
3. Pull the flap away and install protective tape (l) over the locations you just marked, wrapping the tape around both sides of the fender.
4. Install spring nuts (i) over the protective tape on the marked locations.
5. Remove the three factory push pins from the lower front of the factory guard inside the wheel well, and one factory push pin from the underside of the quarter panel, closest to the wheel well.
6. Install bracket to factory hole on the underside of the quarter panel using a cap screw (b) and flat washer (e), and secure using a nylon washer (j), flat washer (d), lock washer (g) and hex nut (h).
7. Place strip nut (k) behind factory holes #9 & #10 and install mud flap holes #4 & #5 through factory holes #9 & #10 into strip nut using a sheet metal screw (c) and flat washer (f). Ensure that you hold the strip nut in place while installing screws.
8. Loosely install mud flap hole #3 to factory hole #8 using a capscrew (b) and flat washer (e) and secure using a nylon washer (j), flat washer (d), lock washer (g), and hex nut (h).
9. Loosely install mud flap holes #1 & #2 to spring nuts (i) installed on the fender lip using a cap screw (a) and flat washer (e).
10. Loosely install mud flap holes #6 & #7 through bracket holes #11 & #12 using a sheet metal screw (c) and flat washer (f)
11. Using a square or bubble level, ensure that the mud flap is square. Tighten all fasteners.
12. Repeat the procedure on the passenger side.

Please check out our YouTube channel to see an install video for this application.

Contact Information

• Add: 1520 – 33 St N Lethbridge, AB T1H 5H3 Canada.
• Toll-free: 1-800-661-8208
• Email: info@truckhardware.ca.
• Website: www.truckhardware.ca.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>