Abletech 592846 Wireless Rear Sensor System User Manual

Abletech 592846 Wireless Rear Sensor System

Please check this manual for instructions on how to use this manual prior to installing and operating this product.

• Speaks,Beep sound back to the situation of rear injury
• Display indicator on the display
• Distinguish LEDs by separating obstacles from both sides

Component

Main Unit connector

1. Power cable
2. Display
3. Sensor1 (Left-7m)
4. Sensor2 (left-4.5m)
5. Sensor1 (right-4.5m)
6. Sensor2 (left-7m)

Display

1. Blinking when the left side of the injury is near Obstacle
2. Mark the distance between the sensor and the obstacle from 2m
3. Blinking when the right side of the injury is near Obstacle
4. volume control
5. RUSS2000E is unavailable.

How to use

• The left and right side LEDs show the position of the left and right hand side of the object when the obstacle is detected.
  If both left and right sides have obstacles, the near side should be placed first display

Sensor installation

• For sensor 2, refer to drawing 1 to locate the position of the upper or lower back
• The sensor is held parallel.
  • If the sensor leans or tilts downwards, a malfunction may occur.
• If fitted, place it at a height of not less than 60 cm above the ground.
• Leave the sensor at least 70 cm apart.
• Leave the sensor at least 20 cm apart from the zero side .
• Between the sensors, 100 cm to 120 cm is the minimum width of the rectangle.

Doing so may cause distortion of the sensor’s wiring, machining morting it, and initiating a malfunction.(Cut-off prohibited)
Processing or modification shall be excluded from the warranty for warranty services, such as repair or replacement.

Sensor sensing range

• Upper mounting point(The principal points in the case of a shade)
  • A vehicle with a shade or protruding edge on the upper part of the head is marked with an awning or projection Check and fix the operation if it does not interfere with the operation.
• Under mounting point(The principal points due to Footstep Effect)
  • Ensure that no obstructions or projections are found in the upper and lower sides of the sensor face (within 30 to 40 cm).
    It is recommended to check the random operation before fastening the sensor. Depending on the height of the protrusion and the width of the folds, the signal may affect the signal. You may need to adjust the distance adjustment or adjust the angle of the sensor.
    (Angle control refers to adding additional double-sided tape between the sensor and the double-sided tape. Please use it.)

Installation of Display

• It is possible to mount the monitor to the monitor stand using a dedicated bracket as shown in Photo 2.
• Remove a fixed bolt from the monitor and monitor stand by inserting a dedicated bracket between the fixing bolts of the monitor stand on the monitor stand. Hold together.
• Prepare the double-sided tape to secure the display.

If you do not secure firmly, make sure you hold it securely, so you can fix it firmly.

Installation of Main Unit

1. Electrical wiring
2. Check the positive (positive) cable and negative cable of the reverse signal around the tail lamp.
3. The + power cable (Red) of this unit is a + line of the reverse signal ; – Power cables (Black) or Connect to the body wire (GND).
4. Cable cables with cable ties.

  * Be sure to remove the power from the reverse signal.
  * One-touch coupler (Red) is also available from 0.3 to 0.85 sp. Do not use thinner wiring.

2. Installation of Main Unit
3. The main body attaches to the inside of the casing (optional) or inside the inner passenger compartment of the passenger compartment. *Avoid areas where humidity is high.
4. Connect the power cable and the sensor cable to the sequence shown in the indicated color (blacksback).
5. Connecting the connector on the main unit

Cautions for installation or use

1. Be careful not to operate or malfunction in the following situations
2. lf non detectable items are rearward.

  * Thin objects such as needles, rope, wire, barbed wire, etc.
  * Objects that absorb ultrasonic waves, such as cotton, sponge, and snow.
2. Cause of malfunction
  * In case of a power source other than the reverse signal
  * Revealing gravel, grass, mounds of sand, hilly roads, and hilly areas.
  * The sensor faces foreign substances such as snow or sand.
  * In case the sensor froze in the winter
  * A communication or electronic device with a large output (noise) is inside the vehicle.

2. This product performs a stable operation when driving at less than 5 km/h.
3. This product is an ultrasound device. Depending on the ambient environment, there may be a difference in voice guidance or distance.

Warning
This product is a device that supports safety during reversing or parking manoeuvres. Regardless of whether this product is fitted or not
Make sure to check with your eyes and move safely. The amount of such errors or losses occurring in reverse order, such as when reversing ; Concerning personnel incidents and damage, we shall not be held liable for the damage.

Specification

guide (10 cm in distance)
Sensing pattern| Fan type radiation curve
Sensing angle| Upper, left, and right each 75± 15″(110±15cm)(-6dB Directivity)
Warning sound| Step  4  Negative or  BEEP sound  : 0.0-0.5/0.6-1.0/1.1-1.5/1 .6-2.0m
Warning Indicator| 7-Segment Show LED distance indicator or sensor position(2pcs)LED
Sensor| 2pcs(sensor cable 4.5m, 2pcs Additional Available : Separate sale) 4pcs(sensor  cable  4.5m  x  2pcs/7m  x 2pcs)
Operating voltage| 12 I 24V Free (+lOV – +30V)
Sensor type| Attachment type(Double-sided tape and  waterproof)
Communication type| Wired (display extension wiring  :  25  m)
Power consumption| Display : – 250 mA under, Main Unit : – 600mA under (12 Volt I 24 V)
Operating temperature| -25″ – +60″
Size| Display  :  97  x 71  x  25mm Main  Unit  :  88  x  60  x  23mm

If you think it’s a fault

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning
 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>