aFe POWER 52-10014D Cold Air Intake System Instruction Manual

aFe POWER 52-10014D Cold Air Intake System

Cold Air Intake System

The Cold Air Intake System is designed for use with Audi Q3 models from 2019 to 2022, equipped with the L4-2.0L (t) 45 TFSI engine. This system includes various components such as air filters, housing, intake tube, couplings, clamps, and a seal trim. The installation process requires 7mm and 8mm nut drivers, as well as a Torx T25 driver.

Product Components:

• Label A1: Air Filter (Pro 5R)
• Label A2: Air Filter (Pro DRY S)
• Label B: Housing
• Label C: Intake Tube
• Label D: Coupling, Silicone Reducer
• Label E: Clamp, #048
• Label F: Seal Trim

Warranty Information: For warranty details,please visit https://afepower.com/contact#warranty.

Emissions Disclaimer: This product is not currently CARB-exempt and cannot be purchased or used on any vehicle registered with the California Department of Motor Vehicles.

Installation Instructions

Step 1: Remove the engine cover

1. Refer to Figure A for visual guidance.
2. Remove the engine cover from your vehicle.

Steps 2 -6: Removal

1. Refer to Figure B for visual guidance.
2. Using a 7mm nut driver, loosen the clamp at the factory turbo inlet (label 2).
3. Disconnect the CCV line (label 3) from the side of the factory air box lid.
4. Disconnect the smog pump fitting (label 4) from the factory air box lid.
5. Using a T25 driver, unscrew the seven screws securing the air box lid to the lower air box.
6. Remove the factory air box lid and intake tube from the vehicle.

Steps 7-8: Removal

1. Refer to Figure C for visual guidance.
2. Remove the factory air filter (label 5) from the vehicle.
3. Remove the factory grate (label 6) from the bottom of the air box by lifting upwards on it.

Steps 9-10: Installation

1. Refer to Figure D for visual guidance.
2. Install the supplied reducer coupling (label 7) and #048 clamp (label 8) with the smaller side on your turbo inlet and tighten using an 8mm nut driver.
3. Place the second #048 clamp (label 9) loosely around the open end of the coupler.

Steps 11-12: Installation

1. Refer to Figure E for visual guidance.
2. Install your aFe POWER air filter into the filter housing (label 10) by firmly pressing it into the opening until the small tabs are locked on the outside. Leave the clamp loose on the filter opening.
3. Install the seal trim (label 11) around the top edge of the filter housing.

Step 13: Installation

1. Refer to Figure F for visual guidance.
2. Install your aFe POWER air filter and housing onto the lower half of the factory air box.
3. Secure the aFe POWER filter housing to the factory lower air box using four of the factory screws from the air box lid.

Steps 14-16: Installation

1. Refer to Figure G for visual guidance.
2. Install your aFe POWER intake tube first into the opening on the air filter, then rotate it downwards into the open end of the coupler at the turbo inlet.
3. Use an 8mm nut driver to tighten all clamps.
4. Reconnect the smog pump hose (label 12) to the fitting on the side of your aFe POWER intake tube.
5. Connect the CCV hose (label 13) to the barbed fitting on your aFe POWER intake tube.

Steps 17-18: Installation

1. Refer to Figure H for visual guidance.
2. Reinstall your engine cover.
3. Check that all components are tight and secure. Your installation is now complete. Thank you for choosing aFe POWER!

NOTE: Check all clamps and connectors are secure after driving 100-200 miles.

Instruction Manual P/N: 52-10014D / 52-10014R

• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• For technical support please call 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.

PARTS

Installation will require the following tools:

7mm & 8mm nut drivers,and Torx T25 driver.

Warranty Information available at https://afepower.com/contact#warranty

Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicles.

INSTRUCTION

Refer to Figure A for Step 1

Step 1: Remove the engine cover 1 .

Refer to Figure B for Steps 2-6

Step 2: Using a 7mm nut driver, loosen the clamp 2 at the factory turbo inlet.

Step 3: Disconnect the CCV line 3 from the side of the factory air box lid.

Step 4: Disconnect the smog pump fitting 4 from the factory air box lid.

Step 5: Using a T25 driver unscrew the seven screws securing the air box lid to the lower air box.

Step 6: Remove the factory air box lid and intake tube from the vehicle.

Refer to Figure C for Steps 7-8
Step 7: Remove the factory air filter 5 from the vehicle.

Step 8: Remove the factory grate 6 from the bottom of the air box by lifting upwards on it.

Refer to Figure D for Steps 9-10

Step 9: Install the supplied reducer coupling 7 and #048 clamp 8 with the smaller side on your turbo inlet and tighten using an 8mm nut driver.

Step 10: Place the second #048 clamp 9 loosely around the open end of the coupler.

Refer to Figure E for Step 11-12
Step 11: Install your aFe POWER air filter into the filter housing 10 by firmly pressing it into the opening until the small tabs are locked on the outside. Leave the clamp loose on the filter opening.

Step 12: Install the seal trim around the top edge of the filter housing 11.

Refer to Figure F for Step 13
Step 13: Install your aFe POWER air filter and housing onto the the lower half of the factory air box. Secure the aFe POWER filter housing to the factory lower air box using four of the factory screws from the air box lid

Refer to Figure G for Step 14-16
Step 14: Install your aFe POWER intake tube first into the opening on the air filter, then rotate it downwards into the open end of the coupler at the turbo inlet. Use an 8mm nut driver to tighten all clamps.

Step 15: Reconnect the smog pump hose 12 to the fitting on the side of your aFe POWER intake tube.

Step 16: Connect the CCV hose 13 to the barbed fitting on your aFe POWER intake tube.

Refer to Figure H for Steps 17-18
Step 17: Reinstall your engine cover.

Step 18: Check that all components are tight and secure. Your installation is now complete. Thank you for choosing aFe POWER!

NOTE: Check all clamps, and connectors are secure after 100-200 miles

advanced FLOW engineering, inc.
252 Granite Street Corona, CA 92879
TEL: 951.493.7100 • TECH: 951.493.7185
E-Mail: Tech@aFepower.com

References

• Contact US/FAQ | aFe POWER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>