LIVEX LIGHTING 45869 Bannister 15 Light Multi Light Pendant Instruction Manual
- June 13, 2024
- Livex Lighting
Table of Contents
LIVEX LIGHTING 45869 Bannister 15 Light Multi Light Pendant
Product Information
- Product Name: Fixture
- Model Number: 45869
- Manufacturer: Livex
- Website: www.livexlighting.com
- Customer Service: 800-761-8056
Product Usage Instructions
- Before starting, ensure that the power is shut off at the fuse or circuit breaker.
- Remove the old fixture and all hardware from the Junction Box.
- Unpack the new fixture and lay out all the parts in a clear area.
- Measure and determine the correct distance for the hole in the mounting plate. Drill three holes in the ceiling at the junction box side.
- Raise the plastic anchor into the hole and attach the mounting plate to the junction box using two junction box screws and three wood screws. Ensure that the side of the mounting plate marked GND faces out.
- Connect the 12-pcs pipes (G) to achieve the desired height. Slide the electrical wires through the pipes and joint (F). Securely tighten by turning clockwise until tight.
- Attach the canopy (D) and steel shim (C) onto the pipe thread of the joint (F) using the lock washer (B) and hex nuts (F).
- If your junction box has a ground wire (green or bare copper), connect the fixture ground wire to it. Otherwise, connect the fixture’s ground wire directly to the Mounting plate with the green screw provided.
- Connect the electrical wires as shown in Fig.2, ensuring that all wire nuts are secured. You may use electrical tape to wrap the connections if necessary.
- Tuck the connected wires carefully inside the Junction Box.
- Raise the lamp body onto the junction box, aligning the screw on the mounting plate with the mounting hole in the canopy. Securely lock it with the round nuts (E).
- Install light bulbs (not included) according to the fixture specifications. Do not exceed the specified wattage.
Your installation is now complete. Return power to the junction box and enjoy your LIVEX Fixture!
ASSEMBLING & INSTALLATION INSTRUCTIONS
- The drawing shown may not exactly match the product enclosed.
- However, the installation instructions do apply to this product.
- WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
- ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
- Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to lose any small parts necessary for installation.
- By measuring, determine the correct distance hole in the mounting plate, then drill three holes(by measuring distance hole) in the ceiling at the junction box of side; raise the plastic anchor and insert the hole. Attach the mounting plate to the junction box with two junction box screws and three wood screws as shown, and tighten the screws securely with the screwdriver. The side of the mounting plate marked “GND” must face out. The junction box is not included.
- This lamp body includes 12 pcs pipes(G) to be connected to various heights. Measure and determine the correct number of pipes required. Slide the electrical wires through the pipes(G) and joints (F). Raise the pipe to top pipe thread of the lamp body(H), by turning it clockwise until tight. Raise the other parts onto the end of pipe thread, by turning it clockwise until tight.
- Attach the canopy(D) and steel shim(C) onto the pipe thread of the joint(F) and lock it securely with the lock washer(B) and hex nuts(F).
- While holding the lamp body towards the ceiling, connect the electrical wires as Shown in Fig.2, making sure that all wire nuts are secured. You may have to wrap the connections with electrical tape. If your junction box has a ground wire (green or bare copper), connect the fixture ground wire to it. Otherwise, connect the fixture’s ground wire directly to the Mounting plate with the green screw provided. After wires are connected, tuck them carefully inside the Junction Box.
- Raise the lamp body onto the junction box, align the screw on the mounting plate with the mounting hole in the canopy, and lock it securely with the round nuts(E).
- Install the light bulbs(Not included) in accordance with the fixture’s specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAG!
Your installation is now complete. Return power to the junction box of the fixture.
- Thank you for purchasing a LIVEX product.
- Need assistance with parts or assembly? Please call customer service at 800-761-8056 Or visit us online at: WWW.LIVEXLIGHTING.COM.
- ©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING, INC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>