KURYAKYN 7352 Front Fender Extension Installation Guide

KURYAKYN 7352 Front Fender Extension

Product Information

The product is a front fender extension designed to protect the motorcycle from dirt, debris, and water splashes. It includes various parts such as a front main splash guard (chrome), lower rubber, lower rubber support, end caps (chrome), fender aluminum step spacers, mounting tape, flat washers, and nylock nuts. The product is manufactured by Kuryakyn and comes with a limited warranty of one year from the date of purchase.

Product Usage Instructions

• Before starting the installation, thoroughly read and understand all the instructions provided.
• Park the motorcycle on a hard, level surface and turn off the ignition.
• Clean the bottom portion of the front fender where the extension will be installed using glass cleaner or a mild solvent. Ensure that all wax, oily  residue, and other contaminants are removed to ensure proper adhesion.
• Trial fit the fender extension and make installation reference marks as shown in PIC 1.
• Note that there are two vertical tabs on the backside of the extension called locating tabs.
• If your bike was previously equipped with a Honda fender extension, the existing holes will be too large. Use the included stepped reducing spacers to reduce the hole size. Insert these spacers from the inside of the fender.
• Rub the adhesive backing of the extension with your finger nail to activate the adhesive.
• Remove all adhesive backing from the inside of the fender extension.
• Align the extension with the reference marks made earlier and firmly press it onto the cleaned surface of the front fender.
• Ensure that the extension is securely attached and properly aligned.
• Follow any additional instructions provided in the installation manual to complete the installation.
  Note: It is important to strictly observe the guidelines provided in the instructions to ensure proper usage of the product and to avoid any potential accidents or damage.

PARTS INCLUDED

• 1 Front Main Splash Guard — Chrome
• 1 Lower Rubber
• 1 Lower Rubber Support
• 2 End Caps – Chrome
• 2 Fender Aluminum Step Spacers
• 1 Mounting Tape
• 2 .50 O.D. x .22 I.D. Flat Washers
• 2 #10-24 Nylock Nuts
• 1 Installation Instructions

Please read and understand entire instructions before starting installation.

THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT.
ATTENTION! This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality.
CAUTION! This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage.

TOOLS SUGGESTED

Set of Drill Bits, Drill, Set of Combination Wrenches, Fine Tip Non-permanent Marker, Ammonia Based Glass Cleaner, Clean rag
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.

• STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition.
• STEP 2 Thoroughly clean the bottom portion of the front fender where the extension will be installed, with glass cleaner or other mild solvent. All wax, oily residue etc. must be removed or the adhesive may not hold to its full potential.

AT TENTION! Ensure the area of installation is free of grease, oil, dirt or other debris to ensure proper adhesion. Küryakyn WILL NOT issue a warranty on any parts lost due to improper installation.

• STEP 3 Trial fit and make installation reference marks. See PIC.1.

NOTE Th: ere are two vertical tabs that are cast into the back-side of the fender extension. These are fender stops. Both tabs should contact the bottom lip of the fender to insure a straight, level orientation. We suggest leaving the adhesive backing on the fender extension and holding the extension into place; this will allow slight movement from side to side so the extension can be positioned to line up with the contour of the fender on both sides. When you are satisfied with the positioning of the extension, hold it firmly in place and mark the (larger) hole locations as well as along the top of the fender extension with a non permanent fine timap r.ker

ATTENTION! If your bike was previously equipped with a Honda fender extension the holes are already drilled, but they will be too large. Two stepped reducing spacers are included. These spacers may be inserted into these holes from the inside of the fender to reduce those size .

ATTENTION! The adhesive will not bond correctly if applied at temperatures less than 50°F. Do not attempt this installation in temperatures less than 50°F.

• STEP 4   Rub the adhesive backing with your finger nail to activate the adhesive. Remove all adhesive backing from the inside of the fender extension.

NOTE: You must be very careful during the installation of the extension. The adhesive is very strong and is intended for a one-time, permanent, installation. Work slowly and precisely. Using the marks you made on the fender, as well as the fender stops inside the extension, set the extension in place and apply firm pressure for one full minute to insure a good, complete adhesive bond.

• STEP 5 While holding the sides of the fender extension tightly against the fender, use the larger holes in each side of the extension as a template to drill the 7/32” mounting holes. The smaller holes on each side are for indexing pins only – do not drill any holes in these locations.

CAUTION! To prevent the tire from being punctured, place something (small piece of wood) between the tire and the fender.

• STEP 6   Insert the studs on the two end caps into the holes you just drilled. The small indexing pins will insert into the smaller of the two holes on each side of the extension. Secure the end caps into place with the included flat washers, and 10-24 Nylock nuts. Do not over torque these nuts.

CUSTOMER SERVICE
877.370.3604 (toll free)

INSTALLATION QUESTIONS
techsupport@kuryakyn.com or call 715.247.2983

LIMITED WARRANTY

Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions:

• Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
• The product must be properly installed, maintained and operated under normal conditions.
• Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products.
• Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between Küryakyn and a customer.
• Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended.
• Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from the date of purchase where as all other components shall be warranted for one(1) year.  This includes, but is not limited to; control modules, wiring, chrome & other components.
• Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies
  with the manufacturer.

ABOUT OUR CATALOG
For purchasing Küryakyn® products, you can receive a complete catalog free of charge. Send the Proof-of-Purchase below with your address to: Küryakyn, P.O. Box 339, Somerset, WI 54025.
Please indicate either Accessories Catalog for Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.

FRONT FENDER EXTENSION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>