algam MB100 100W LED Beam Moving Head User Manual

: June 13, 2024
: algam

Table of Contents

SAFETY INSTRUCTIONS
PRODUCT INSTALLATION
INSTALLATION – RIGGING
PRODUCT PRESENTATION
MENU AND CONTROLS
DMX PROTOCOL
SPECIFICATIONS
SPECIAL INSTRUCTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MB100
100W LED BEAM MOVINGHEAD User Manual algam MB100 100W LED Beam
Moving Head - Symbols 1

Thank you for choosing one of our Algam Lighting products. Please read this user’s manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user’s guide for future reference.

SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols to warn of potential hazards related to the use of electrical dangers associated with the use of electrical equipment. If any of these symbols are present on your device, please read the following instructions:

| ATTENTION !
Before using your equipment, we recommend that you read all the instructions in this manual.
---|---
| ATTENTION !
This device produces an intense and powerful light. Risk to the eyes. Do not look directly into the beam.
| DANGER !
Hazardous voltage, risk of electric shock. Do not open the product. To reduce the risk of electric shock do not expose this equipment to rain or moisture.
| ATTENTION !
Risk of burns. The exterior of the unit can become very hot. Do not touch within 10 minutes of use.
| ATTENTION !
Fire hazard. Keep all combustible and flammable materials away from the materials away from the unit during operation.
| DANGER !
Safety hazard. This appliance presents a significant risk of injury. Follow the safety instructions.
| Place the unit at least 50cm away from flammable materials and walls.

INSTALLATION

Unpack and check carefully for transport damage before using the product. Never put a damaged product into operation.
This product must be installed with strong hooks of adequate size for the weight carried. The product must be screwed to the hooks and tightened properly to prevent it from falling due to vibrations. Also check that the structure (or hanging point) can support at least 10X the weight of the hanging unit. The device must be installed by a qualified person and must be placed out of reach of the public. It is necessary to use a secondary hanging system (safety sling) approved for the weight of the device.
This unit is intended for indoor use only. Exposing the unit to rain or moisture may result in electric shock or fire.
Do not place the unit, speakers or any other object on top of the power cord and make sure it is not pinched.
For proper protection against electric shock, the unit must be connected to earth (ground). The electrical supply circuit must be equipped with a fuse or circuit breaker and a differential protection device.
Power Disconnection Notice: To disconnect the device from the power source, the power plug must be removed from the power outlet. For this reason, the device must be placed in a position that allows constant, unobstructed access to the power outlet. This way, in case of an emergency, you can disconnect the power plug immediately.
The unit should only be installed in a well ventilated area. Make sure that no ventilation slots are blocked. To ensure adequate ventilation, leave at least 20 cm of free air space around the sides and top of the unit.
USAGE
This appliance must not be used by persons (including children) with limited physical, physiological or mental capabilities or lack of experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by that person in the operation of the appliance.
Never leave this equipment unattended.
If you experience any problems with the unit, stop using it immediately. Do not attempt to repair it yourself. Contact your dealer or an authorized service center. There are no user replaceable parts.
NEVER use the unit under the following conditions:

In areas subject to vibration or bumps,
In places where the ambient temperature is above 45 ° C or below 2 ° C.
In areas exposed to excessive dryness or humidity (ideal conditions: between 35% and 80%).
Never use the unit near flames, flammable or explosive materials or hot surfaces. Doing so may cause a fire.
The exterior of the unit can become very hot. It is important to avoid contact with the unit during operation and for at least 10 minutes after use.
It is important to use the supplied power cable (grounded cable).
Before turning on the power, make sure that the voltage and frequency of the power supply match the power requirements of the unit, as described in this manual.
Never cut or tamper with the power cord or plug. If a power cord is provided with a ground wire, it is required for safe operation! Risk of fatal electric shock!
Always hold the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this may cause a short circuit or electric shock.
Do not connect this device to a dimmer pack
DO NOT allow liquids or objects to enter the unit. If liquid is spilled on the unit, immediately UNPLUG the power supply to the unit and contact customer service.
You must ensure that the power cord never gets wet during operation. Before a thunderstorm and/or a lightning storm, unplug the unit from the mains.
Under no circumstances should you open the housing of the device. If you do, your safety will not be assured. There are no operational components inside, only dangerous voltages that can give you a fatal shock!

MAINTENANCE / SERVICE

Never attempt to disassemble, repair or modify the unit yourself. Otherwise, the warranty becomes void. Repairs by unqualified persons may result in damage or malfunction. Please contact the nearest authorized service center. The light source contained in this fixture should only be replaced by the manufacturer or its service agent or a person of equivalent qualification.
Screens, lenses or UV filters should be replaced if they are visibly damaged to an extent that compromises their effectiveness, such as by deep cracks or scratches.
The lamp should be replaced if it has been damaged or deformed by heat.
Disconnect the unit from the mains before servicing.
If the cable or flexible outer cord of this fixture is damaged, it must be replaced with a special cable or cord from the manufacturer or its service agent only.
Never immerse the unit in water or any other liquid. Wipe only with a slightly damp cloth.

PRODUCT INSTALLATION

POWER SUPPLY
Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device’s power should be connected separately, so that device can be controlled individually.
DMX CONNECTION
Connection between laser lights and DMX must use the shield cable of diameter more than 0.5mm. Please use the attached pin XLR plug/socket to connect the DMX output/input interface. The connection between sokcet and cable as below (note the plug/socket’s 3 pin number and position). algam MB100 100W LED Beam
Moving Head - CONNECTION When using standard DMX512 control signal, the last device’s output interface must be connected to a DMX plug.
This plug is putting a 120 ohm resistance between “canon” plug’s 2 pin and 3 pin. Showing as below pic. Sticking this plug into the last device’s signal output interface, it will avoid the interference during the process of signal transmission.

INSTALLATION – RIGGING

This fixture can be installed on the floor on a flat and stable surface. It can be clamped to a struss or similar rigging structure in any orientation.
Check that the rigging structure can support at least 10 times the weight of all fictures and equipment which are installed on it. When installing the fixture on truss, it is recommanded to use half-coupler clamp (see below). One or two pieces OMEGA ( depends on the version) brackets are supplied with the fixture . Fix the rigging clamp with self-locking nuts to the OMEGA . OMEGA brackets are locked to the fixture with 1/4 turn fast lock screw system.
SECURE WITH SAFETY CABLE !
Secure the fixture with safety cable.

PRODUCT PRESENTATION

algam MB100 100W LED Beam Moving Head - PRESENTATION

FONCTION	DESCRIPTION
1 LED error indicator	Flashes to indicate that there is an error message
2 LED DMX indicator	Lights ON when the DMX signal is received
3 LCD display	Menu and function display
4 Keyboard	For menu and sub-menu navigation
5 Mains switch	Power switch ON/OFF
6 Protection fuse	Electric fuse protection
7 Power OUT connector	To connect more fi xtures . Load max. 960W
8 Power IN connector	Power input. Use incuded power lead
9 DMX OUTXLR connector	DMX signal output
10 DMX IN XLR connector	DMX signal input

algam MB100 100W LED Beam Moving Head - CONTROLS Use buttons and to navigate in main menu. Press to confi rm your selection.
Man MANUAL CONTROL

Manual

1. Pan| 0
2. Pan Fine| 0
3. Tilt| 128
4. Tilt Fine| 0

Use and to navigate into menu and sub-menu.Yellow arrow indicates selected line.
Press key to enter into edit status, the value becomes RED, then use et to select , then press to validate.
Press ** to come back into previsou function or menu.
Set SETTINGS**

Setting

Run Mode| DMX
DMX Address| 1
Sensitivity| 1
Channel Mode| 16CH

DMX
Slave status: Receive DMX signals from the console or Master
AUTO1 Auto run ;
AUTO2
Random Master status: Auto run and send
DMX signal to slave
Sound

DMX ADDRESS| 001-512| Press key enter into edit status, then press to change DMX address.
press key save and exit edit status.
---|---|---
CHANNEL MODE| 16CH
20CH| Standard 16 Channel Mode, 17-20CH No Function
Extend 20 Channel Mode, 17-20CH for speed control.
(please check the detail on Channel table.)
TOP LAMP TEMP| 0-110| Affichage de la température de la LED (en °C)
INVERT PAN| ON
OFF| ON for starting and ending , the default is OFF.
INVERT TILT| ON
OFF| ON for starting and ending , the default is OFF.
PAN-TILT SWAP| ON
OFF| Exchange Pan/Tilt channel (include Pan/Tilt Fine)
PAN-TILT ENCODER| ON
OFF| Use encoder (optocoupler) to determine out of step and automatically correct position
Correct position without encoder (optocoupler)
DMX SIGNAL| KEEP
CLEAR| Continue running as it is
All motors return to the position and stop running.
LINEAR COLOR| ON
OFF| Color liner change
Color nonlinear change, half color change
LOAD DEFAULT| OK| Press the button to see the confirmation dialog, press again The key restores the default settings

Sys SYSTEM PARAMETERS

System

V T108A-LED100-A001
Reset cal|
Sensor Monitor|
System Errors|
VERSION NO.(V)| Version No.
---|---
RESET
CALIBRATION| Pan Calibration
Tilt Calibration
Color Calibration
Gobo Calibration
Focus Calibration
Prism1 Calibration
Prism2 Calibration
Rainbow Calibration
Frost Calibration| After entering the subinterface,
you can adjust the motor such as
X-axis and Y-axis.
Reset position to compensate for
errors in hardware installation,
Adjustment range – 128~+127, +0
means no adjustment.
SENSOR MONITOR| Pan Hall
Tilt Hall
Color Hall
Gobo Hall
Focus Hall
Prism1 Hall
Prism2 Hall
Panwheel State
Tiltwheel State
Panwheel Step
Tiltwheel Step| 0 when magnetic is detected, otherwise 1
2 digits, each corresponding to a photoelectric switch in the encoder disc
When walking in the positive direction, the step value should increase, when going back,
SYSTEM ERRORS| (See common mistakes Rear)| If the red ERR indicator is lit, the luminaire is running.
An error can be made by going to the sub-interface for details. After viewing, you can press the “Clear” button to clear the error record.
DMX MONITOR| | This enters the subinterface and displays the channel values as values for viewing.

ERRORS

MT BOARD CONNECTION FAILED| The driver board did not respond. Serial communication line connecting display
panel and driver board There is a problem, or there is a problem with the driver board.
---|---
PAN RESET FAILED| X-axis photoelectric switch, or problem with X-axis motor
TILT RESET FAILED| Y-axis photoelectric switch, or problem with Y-axis motor
PAN HALL FAILED| Pan Hall have problem
TILT HALL FAILED| Tilt Hall have problem
COLOR WHEEL RESET FAILED| Color Wheel Hall , or Color Wheel motor have problem
GOBO WHEEL RESET FAILED| Gobo Wheel Hall , or Gobo Wheel motor have problem
FOCUS RESET FAILED| Focus Hall , or Focus motor have problem

DMX PROTOCOL

CHANNEL	FUNCTION	VALUE	EFFECT
CH1	Pan	0-255	Pan 540 degree scan
CH2	Pan Fine	0-255	Pan 1.2 degree scan
CH3	Tilt	0-255	Tilt 270 degree scan
CH4	Tilt Fine	0-255	Tilt 1.2 degree scan
CH5	Dimmer	0-255	From dark to bright
CH6	Strobe	000-003	OFF
004-251	Strobe from slow to fast
252-255	ON > (control by dimmer channel)
CH7	Color Wheel	000-004	White
005 -009	White + Colon
010 – 014	Color 1
015 – 019	Color 1 + Color 2
020 – 024	Color 2
025 – 029	Color 2 + Color 3
030 – 034	Color 3
035 – 039	Color 3 + Color 4
040 – 044	Color 4
045 – 049	Color 4 + Color 5
050 – 054	Color 5
055 – 059	Color 5 + Color 6
060 – 064	Color 6
065 – 069	Color 6 + Color 7
070 – 074	Color 7
075 – 079	Color 7+ Color 8
080 – 084	Color 8
085 – 089	Color 8 + Color 9
090 – 094	Color 9
095 – 099	Color 9 + White
100 -177	Positive flow (from fast to slow)
178 – 255	Reverse flow(from slow to fast)

CHANNEL	FUNCTION	VALUE	EFFECT
CH8	Gobo Wheel	000-004	White
005 -009	Gobo 1
010 – 014	Gobo 2
015 – 019	Gobo 3
020 – 024	Gobo 4
025 – 029	Gobo 5
030 – 034	Gobo 6
035 – 039	Gobo?
040 – 044	Gobo 8
045 – 049	Gobo 9
050 – 054	Gobo 10
055 – 059	Gobo 11
060 – 064	Gobo 12
065 – 069	Gobo 13
070 – 074	Gobo 14
075 – 079	Gobo 15
080 – 084	White shake(from slow to fast)
085 – 089	Gobo 1 shake(from slow to fast)
090 – 094	Gobo 2 shake (from slow to fast)
095 – 099	Gobo 3 shake (from slow to fast)
100 -104	Gobo 4 shake (from slow to fast)
105 -109	Gobo 5 shake (from slow to fast)
110 – 114	Gobo 6 shake (from slow to fast)
115 -119	Gobo 7 shake (from slow to fast)
120 -124	Gobo 8 shake (from slow to fast)
125 -129	Gobo 9 shake (from slow to fast)
130 -134	Gobo 10 shake (from slow to fast)
135 -139	Gobo 11 shake (from slow to fast)
140 -144	Gobo 12 shake(from slow to fast)
145 – 149	Gobo 13 shake (from slow to fast)
150 -154	Gobo 14 shake (from slow to fast)
155 -159	Gobo 15 shake (from slow to fast)
160 – 207	Positive flow If rom fast to slow)
208 – 255	Reverse flow (f rom slow to fast)
CHANNEL	FUNCTION	VALUE	EFFECT
---	---	---	---
C1-I9	Prism 1	000-127	Prism 1 out
128-255	Prism 1 in
CH10	Prism 1 Rotation	000-127	Prism angle adjustment
128-190	Reverse rotation (from fast to slow)
191-192	Stop
193-255	Forward rotation (from slow to fast)
CH11	Prism 2	000-127	Prism 2 out
128-255	Prism 2 in
CH12	Prism 2 Rotation	000-127	Prism angle adjustment
128-190	Reverse rotation (from fast to slow)
191-192	Stop
193-255	Forward rotation (from slow to fast)
CH13	Focus	0-255	Pattern definition from far to near
CH14	7-Color Effect	000-127	7-Color Effect out
128-255	7-Color Effect in
CH15	Frost	000-127	Frost out
128-255	Frost in
CH16	Reset	000-049	No Function
050-099	Small Motor Reset
100-199	Big Motor(Pan/Tilt) Reset
200-255	All Motor Reset

EXTEND CHANNEL

CANAL	FONCTION	VALEUR	EFFET
CH17	Pan/Tilt Speed	000-255	Speed from fast to slow
CH18	Color Wheel Speed
CH19	Dimmer-Prism-Frost Speed
CH2O	Gobo Wheel Speed

SPECIFICATIONS

Lighting source	100W WHITE LED
Average Lifetime	50 000 hours
Color temperature	7000k – 7500k
Brightness	123000lux@4m
Color wheel	9 colors+white, rotation with variable direction and speed
Gobo wheel	15 gobos+open, wheel rotation and shake effect
Shutter	Strobe effect, pulse effect
Prism	Dual prism 8 and 16 facets with vaiable speed rotation
Frost	Motorized
Focus	Motorized 100% linear
Dimmer	0-100% linear curve
PAN	540° with fine control and position calibration and position auto-

SPECIAL INSTRUCTIONS

During the reset process, press and hold the 5 seconds button to interrupt the reset.
Press and hold the key during power-on to interrupt the reset process and enter test mode.
SIGNAL INDICATOR
The ERR red indicator flashes to indicate that there is an error message and enters the “System Information” > System Error” view information.
DMX green indicator light, steady light indicates that the DMX signal is received, and frequent off indicates no DMX signal.

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version.
Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal arm or through your local waste facility.
When discarding the device, comply with the rules and regulations that apply in your country.
If in doubt, consult your local waste disposal facility.
This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:
LVD Directive 2014/35/EU :
EMC Directive 2014/30/EU :
RoHS 2 Directive 2011/65/EU
The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at : contact@algam.net algam MB100 100W
LED Beam Moving Head - Notes algam MB100 100W LED Beam
Moving Head - Fig