algam Lighting MHE60 Wash Moving Head 60W With Laser Beam Instruction Manual
- June 13, 2024
- algam Lighting
Table of Contents
algam Lighting MHE60 Wash Moving Head 60W With Laser Beam
Thank you!
Thank you for choosing one of our Algam Lighting products. Please read this user’s manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user’s guide for future reference.
SAFETY INSTRUCTIONS
The symbols shown above are internationally accepted symbols to warn of potential hazards related to the use of electrical dangers associated with the use of electrical equipment. If any of these symbols are present on your device, please read the following instructions:
ATTENTION!
Before using your equipment, we recommend that you read all the instructions
in this manual.
ATTENTION!
This device produces an intense and powerful light. Risk to the eyes. Donot
look directly into the beam. Do not expose yourself to laser radiation,
asthere is a risk of burns.
DANGER!
Hazardous voltage, risk of electric shock. Do not open the product. To reduce
the risk of electric shock do not expose this equipment to rain or moisture.
ATTENTION!
Risk of burns. The exterior of the unit can become very hot. Do not touch
within 10 minutes of use.
ATTENTION!
Fire hazard. Keep all combustible and flammable materials away from the
materials away from the unit during operation.
DANGER!
Safety hazard. This appliance presents a significant risk of injury. Follow
the safety instructions.
Place the unit at least 50cm away from flammable materials and walls.
INSTALLATION
- Unpack and check carefully for transport damage before using the product. Never put a damaged product into operation.
- This product must be installed with strong hooks of adequate size for the weight carried. The product must be screwed to the hooks and tightened properly to prevent it from falling due to vibrations. Also check that the structure (or hanginpoint) can support at least 10X the weight of the hanging unit. The device must be installed by a qualified person and must be placed out of reach of the public. It is necessary to use a secondary hanging system (safety sling) approved for theweight of the device.
- This unit is intended for indoor use only. Exposing the unit to rain or moisture may result in electric shock or fire.
- Do not place the unit, speakers or any other object on top of the power cord and make sure it is not pinched.
- For proper protection against electric shock, the unit must be connected to earth (ground). The electrical supply circuit must be equipped with a fuse or circuit breaker and a differential protection device.
- Power Disconnection Notice: To disconnect the device from the power source, the power plug must be removed from the power outlet. For this reason, the device must be placed in a position that allows constant, unobstructed access to thepower outlet. This way, in case of an emergency, you can disconnect the power plug immediately.
- The unit should only be installed in a well ventilated area. Make sure that no ventilation slots are blocked. To ensure adequate ventilation, leave at least 20 cm of free air space around the sides and top of the unit.
USAGE
- Never leave this equipment unattended.
- If you experience any problems with the unit, stop using it immediately. Do not attempt to repair it yourself. Contact your dealer or an authorized service center. There are no user replaceable parts.
- NEVER use the unit under the following conditions:
- In areas subject to vibration or bumps,
- In places where the ambient temperature is above 45 ° C or below 2 ° C.
- In areas exposed to excessive dryness or humidity (ideal conditions: between 35% and 80%).
- Never use the unit near flames, flammable or explosive materials or hot surfaces. Doing so may cause a fire.
- The exterior of the unit can become very hot. It is important to avoid contact with the unit during operation and for at least 10 minutes after use.
- It is important to use the supplied power cable (grounded cable).
- Before turning on the power, make sure that the voltage and frequency of the power supply match the power requirements of the unit, as described in this manual.
- Never cut or tamper with the power cord or plug. If a power cord is provided with a ground wire, it is required for safe operation! Risk of fatal electric shock!
- Always hold the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this may cause a short circuit or electric shock.
- Do not connect this device to a dimmer pack
- DO NOT allow liquids or objects to enter the unit. If liquid is spilled on the unit, immediately UNPLUG the power supply to the unit and contact customer service.
- You must ensure that the power cord never gets wet during operation. Before a thunderstorm and/or a lightning storm, unplug the unit from the mains.
• Under no circumstances should you open the housing of the device. If you do, your safety will not be assured. There are no operational components inside, only dangerous voltages that can give you a fatal shock!
MAINTENANCE / SERVICE
- Never attempt to disassemble, repair or modify the unit yourself. Otherwise, the warranty becomes void. Repairs byunqualified persons may result in damage or malfunction. Please contact the nearest authorized service center. The light source contained in this fixture should only be replaced by the manufacturer or its service agent or a person of equivalent qualification.
- Screens, lenses or UV filters should be replaced if they are visibly damaged to an extent that compromises their effectiveness, such as by deep cracks or scratches.
- The lamp should be replaced if it has been damaged or deformed by heat.
- Disconnect the unit from the mains before servicing.
- If the cable or flexible outer cord of this fixture is damaged, it must be replaced with a special cable or cord from the manufacturer or its service agent only.
- Never immerse the unit in water or any other liquid. Wipe only with a slightly damp cloth.
CAUTION
**** Read carefully this user manual, and follow the safety precautions
listed in this manual before use and before installating this fixture. Keep
this manual for future reference.
This fixture is conformed and complying with european standard NF EN
60825-1:2014/A11:2021.
EXPLANATION OF THE NAMEPLATES ON YOUR DEVICE :
CLASS 3R LASER PRODUCT:
AVOID DIRECT
EYE EXPOSURE
HAZARDOUS EXPOSURE
LASER RADIATION
IS EMITTED FROM
THIS APERTURE
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Avoid exposure to laser rays, as there is a risk of burns. In this context, also exercise extreme caution when using optical instruments in the vicinity of the device (glasses, camera, binoculars, etc.). Avoid any flammable substances or objects in the laser’s scanningarea. Incorrect installation or use of the laser may result in personalinjury, fire or explosion.
This device is intended for use in professional entertainment and display applications only. This device has been developed for professional use and is not suitable for domestic lighting.
In some countries, the installation and use of lasers is subject to approval
by the relevant authorities. Consult and follow local regulations.
Distances between the device and the public or maximum permissible exposures
are defined by each country and must be assessed by a trained and qualified
professional. In some countries, lasers may only be installed and used in
places open to the public by a designated Safety laser officer. Please contact
your local authorities for further information.
DÉCRET N°2012-1303 (FRANCE)
When in use, this device must be installed in such a way that the rays remain
above eye level and do not reach the public under any circumstances.
DÉCRET N° 2007-665 (FRANCE)
This device is a laser projector for show and display purposes. It is not a
laser pointer and must not be used as such.
It is forbidden to use this device for any purpose other than that for which
it is intended.
The manufacturer and distributor are not responsible for damage caused by ALGAM LIGHTING brand lasers. The user is solely responsible for use and compliance with regulations arising from EN 60825-1:2014/A11:2021 and applicable local regulations.
PRODUCT INSTALLATION
POWER SUPPLY
Please use the attached power, note that power voltage and frequency are the
same as the marked voltage and frequency of device when connecting power.
Every device’s power should be connected separately, so that device can be
controlled individually.
CABLE SPEC.
CABLE (EU) | CABLE (US) | PIN | INTERNATIONAL |
---|---|---|---|
Brown | Black | Live | L |
Light blue | White | Neutral | N |
Yellow/Green | Yellow/Green | Earth |
__
DMX CONNECTION
Connection between laser lights and DMX must use the shied cable of diameter
more than 0.5mm. Please use the attached 3 pin XL plug/socket to connect the
DMX output/input interface. The connection between socket and cable as below
(note the plug/socket’s 3 pin number and position).
RIGGING
Attention! The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected, Certified installation materials should be used, the installed device should be inspected regularly for safety.
**** Before rigging make sure that installation area can hold the 10 times weight of device.
OPERATION INSTRUCTIONS
1 Keyboard | For value selection & menus navigation |
---|---|
2 Display | Display menu and values |
3 DMX input | DMX signal input – XLR 3 pin |
4 DMX output | DMX signal Output – XLR 3 pin |
5 Fuse holder | Protection fuse , replace with same value fuse |
6 Power supply Input | 220 – 240V~ power supply INPUT |
MENU OPERATING INSTRUCTION
Mode Option, to choose the operating mode of laser.
Confirmation, to confirm the laser to show the present mode at the next operation.
UP/DOWN, to change operating mode, parameter or DMX address.
MENU
| ****| DMX address setting
---|---|---
|
| 16Channel setting
| | DMX512 Mode
| Sound mode
| Auto mode
|
| Effect 1
| Effect 2
****| Effect 3
| | Adjust the sensitivity of sound
` `| ****| Turn off the screen after 5 seconds
| Screen open all the time
| | Display reverse
| Display forward
| | X motor forward
| X motor reverse
****|
| Y motor forward
| Y motor reverse
| | Default mode
****| | System reset
DMX PROTOCOL – 16 CHANNELS
CANAL | VALEUR | CONTENT |
---|---|---|
CH1 | 0-255 | Pan Running |
CH2 | 0-255 | Pan fine adjustment |
CH3 | 0-255 | Tilt Running |
CH4 | 0-255 | Tilt fine adjustment |
CH5 | 0-255 | Running Speed in Pan/Tilt |
CH6 | 0-255 | Dimming from dark to bright |
CH7 | 0-255 | Strobe from slow to fast |
CH8 | 0-255 | Red dimming |
CH9 | 0-255 | Green dimming |
CH10 | 0-255 | Blue dimming |
CH11 | 0-255 | White dimming |
CH12 | 0-127 | Manual control |
128-191 | Motor rotation clockwise from fast to slow | |
192-255 | Motor rotation anti-clockwise from slow to fast | |
CH13 | 0-255 | Green laser light control |
CH14 | 0-29 | Channel 1- 13 is valid |
30-149 | Auto mode | |
150-255 | Sound mode | |
CH15 | 0-255 | Auto speed |
CH16 | 0-240 | – |
250-255 | Reset after 3 seconds |
SPECIFICATIONS
Dimensions | 95x170x280mm |
---|---|
Net weight | 5.9kg |
Power supply type | Switching power supply (International) |
Power supply. | 220-240V~ 50/60Hz |
Power consumption | 120W |
DMX | 16 channels |
Angles PAN | 540° |
Angles TILT | 270° |
Modes | Auto, music, master/slave |
Lighting source | 6 x LED CREE RGBW 15W |
Effects | Rotating wheel with LASER effect |
LASER source | 1 x Green LASER diode 50mw/532nm / Multipoint |
This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version.
Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal arm or through your
local waste facility.
When discarding the device, comply with the rules and regulations that apply
in your country. If in doubt, consult your local waste disposal facility.
This Algam Lighting product is compliant to all required UE certifications and
conformed to following
standard and UE directives:
LVD Directive 2014/35/EU :
EMC Directive 2014/30/EU :
RoHS 2 Directive 2011/65/EU
The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask
for it at : contact@algam.net