algam Lighting MW19x15Z 19x15W LED Wash Movinghead Instruction Manual

: June 13, 2024
: algam Lighting

Table of Contents

MW19x15Z 19x15W LED Wash Movinghead
SAFETY INSTRUCTIONS
PRODUCT INSTALLATION
INSTALLATION – RIGGING
PRODUCT PRESENTATION
MENU AND CONTROLS
DMX PROTOCOL – 15 CHANNELS
DMX PROTOCOL – 23 CHANNELS
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MW19x15Z 19x15W LED Wash Movinghead
Instruction Manual

MW19x15Z 19x15W LED Wash Movinghead

algam Lighting MW19x15Z 19x15W LED Wash Movinghead MW19x15Z
Lyre assertive Wash 19x15W
19x15W LED Wash Movinghead

Thank you for choosing one of our Algam Lighting products. Please read this user manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user guide for future reference.

SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products.
if one of those symbols is on your product , please read carefully the following:
WARNING !
Before use, and before installing this ﬁxture, read carefully user manual, and follow the safety precautions listed on this page.
WARNING !
Very high level light output. DO NOT LOOK INTO THE BEAM.
DANGER !
Hazardous voltage, Risk of electric shock!
ALWAYS disconnect the ﬁxture from power for servicing, for cleaning or installing. Do not connect this unit on a dimmer power pack.
Protect the unit from rain or moisture.
Locate the fixture in a well ventilated spot, away from flammable materials.
The fixture must be fixed at least 50cm from surrounding walls .
WARNING !
Burn Hazard. Do not touch. Very hot surface.
The ﬁxture becomes hot during use and remains hot 10 min after use. Do not touch the unit.
WARNING !
Fire Hazard!
Keep ﬂammable materials away from the ﬁxture. Do not operate the ﬁxture with ambient temperature over 4O°C.
DANGER !
Safety Hazard. Risk of injury.
This unit must be installed by professional people. If suspended, make sure the structure and the hardware used for this suspension is secured. This Hardware must support at least 10 times the weight of the device suspended.
Ensure public is not looking at the beam. Do not try to repair the ﬁxture by yourself. Contact a professional repair service.

Please carefully read the instruction, which includes important information about the installation, usage and maintenance, BEFORE operating this device.

This device is exclusively meant to be used as a splitter for DMX signals within the limits given in this manual. Using it in any other way you risk electric shock and warranty will become void.
Never sever or manipulate the power cord or the plug. If a power cord is provided with an earth lead, this is mandatory to ensure safe operation! Otherwise a LIFE THREATENING situation exists!
Unpack and check carefully there is no transportation damage before using the unit. Never put a damaged device into operation.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit as stated in this manual.
The unit is for indoor use only. Use it only in a dry location. Exposing the device to rain or moisture would cause the risk of electrical shock or fire.
DO NOT let any liquids or objects enter the unit. Should any liquid be spilled on the unit, DISCONNECT the power supply to the unit immediately and contact the service company.
The unit must only be installed in a location with adequate ventilation. Be sure that no ventilation slots are blocked. In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.
Disconnect the device from the mains power before any servicing or maintenance. Notice regarding power disconnection: To disconnect the device from the power source the power plug must be removed from the power socket. For this reason the device must be placed in a position where a constant unobstructed access to the power socket is assured, thus in an emergency situation you are able to immediately pull out the power plug. To eliminate the risk of fire you must completely disconnect the power plug from the power socket after the device has been used.
Always grasp the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this could result in a short circuit or an electrical shock. Do not place the device, speaker cabinets or anything else on the power cord and make sure that it does not become clamped.
Before a storm and/or a thunderstorm with a risk of lightning, disconnect the device from the mains power supply.
Under no circumstances may you open the device housing. Should you do so your safety would not be assured. There are no operational components whatsoever inside, only dangerous voltages that can give you a deadly shock!
NEVER use the unit under the following conditions :> In places subject to vibrations or bumps.> In places with a temperature of over 45 °C or less than 2 °C.> In places subject to excessive dryness or humidity (ideal conditions are between 35% and 80%).
Never submerse the device in water or any other liquid. Only wipe it with a slightly damp cloth.
Never operate the device near flames, flammable, explosive materials, or hot surfaces. Otherwise you run the risk of causing a fire.
Never leave this device running unattended.
This appliance must not be used by individuals (including children) with restricted physical, physiological or intellectual abilities or deficiencies in experience and/or knowledge unless they are supervised by a person responsible for their safety or receive from this person instruction in how the appliance is to be used.
Keep children away from the device and power cord! Children frequently underestimate the dangers of electrical devices. Also keep the plastic packaging well away from small children. There is a risk of suffocation!
In the event of serious operating problems, stop using the unit immediately. Never try to dismantle, repair or modify the unit by yourself. Otherwise warranty becomes void. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance centre.

PRODUCT INSTALLATION

Power supply

Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device’ s power should be connected separately, so that device can be controlled individually.

DMX connection
Connection between laser lights and OMX must use the shied cable of diameter more than 0.5mm. Please use the attached 3 pin XLR plug/socket to connect the DMX output/input interface. The connection between socket and cable as below( note the plug/socket’ s 3 pin number and position). algam Lighting MW19x15Z
19x15W LED Wash Movinghead - DMX

When using standard DMX512 control signal, the last device’ s output interface must be connected to a OMX plug. This plug is putting a 120 ohm resistance between “canon” plug’ s 2 pin and 3 pin. Showing as below pie. Sticking this plug into the last device’ s signal output interface, it will avoid the interference during the process of signal transmission.

INSTALLATION – RIGGING

This fixture can be installed on the floor on a flat and stable surface. It can be clamped to a Struss or similar rigging structure in any orientation.
Check that the rigging structure can support at least 10 times the weight of all factures and equipment which are installed on it.
When installing the fixture on truss, it is recommended to use half-coupler clamp ( see below).

One or two pieces OMEGA ( depends on the version) brackets are supplied with the fixture . Fix the rigging clamp with self-locking nuts to the OMEGA . OMEGA brackets are locked to the fixture with 1/4 turn fast lock screw system.
Secure with safety cable !
Secure the fixture with safety cable.

PRODUCT PRESENTATION

algam Lighting MW19x15Z 19x15W LED Wash Movinghead -
PRESENTATION

| FUNCTION| DESCRIPTION
---|---|---
1| LED error indicator| Flashes to indicate that there is an error message
2| LED DMX indicator| Lights ON when the DMX signal is received
3| LCD display| Menu and function display
4| Keyboard| For menu and sub-menu navigation
5| Protection fuse| Electric fuse protection
6| Power OUT connector| To connect more fixtures . Load max. 960W
7| Power IN connector| Power input. Use incuded power lead
8| DMX OUTXLR connector| DMX signal output
9| DMX IN XLR connector| DMX signal input

Use buttons UP and DOWN to navigate in main menu. Press ENTER to confirm your selection.

Option	Description
Setting	DMX Addr
Encoder	YES : the encoder (optocoupler) to judge out-off-step and

automatically correct position.
NO : Correct position without using encoder (optocoupler).
Pandeva| YES / NO
Tilter| YES / NO

Run Mode

| Run Mode| DMX / AUTO / SOUND
Channel| 15CH / 23CH

Display

DMX PROTOCOL – 15 CHANNELS

Channel	Function	Value	Description
1	Pan	000-255	Pan 540degree Movement
2	Pan Fine	000-255	Pan Fine
3	Tilt	000-255	Tilt 270degree Movement
4	Tilt Fine	000-255	Tilt Fine
5	P/T Speed	000-255	P/T Speed from slow to fast
6	Zoom	000-255	Zoom from wide to narrow
7	Dimmer	000-255	Dimmer from dark to brighter

8

|

Strobe

DMX PROTOCOL – 23 CHANNELS

Channel	Function	Value	Description
1	Pan	000-255	Pan 540degree Movement
2	Pan Fine	000-255	Pan Fine
3	Tilt	000-255	Tilt 270degree Movement
4	Tilt Fine	000-255	Tilt Fine
5	P/T Speed	000-255	P/T Speed from slow to fast
6	Zoom	000-255	Zoom from wide to narrow
7	Dimmer	000-255	Dimmer from dark to brighter

8

|

Strobe

| 000-009| No Strobe
010-255| Strobe from slow to fast
9| Red 1| 000-255| First Group Red dimmer from dark to brighter
10| Green 1| 000-255| First Group Green dimmer from dark to brighter
11| Blue 1| 000-255| First Group Blue dimmer from dark to brighter
12| White 1| 000-255| First Group White dimmer from dark to brighter
13| Red 2| 000-255| Second Group Red dimmer from dark to brighter
14| Green 2| 000-255| Second Group Green dimmer from dark to brighter
15| Blue 2| 000-255| Second Group Blue dimmer from dark to brighter
16| White 2| 000-255| Second Group White dimmer from dark to brighter
17| Red 3| 000-255| Third Group Red dimmer from dark to brighter
18| Green 3| 000-255| Third Group Green dimmer from dark to brighter
19| Blue 3| 000-255| Third Group Blue dimmer from dark to brighter
20| White 3| 000-255| Third Group White dimmer from dark to brighter
---|---|---|---

21

|

Macro Function

23

|

Reset

| 000-249| No function
250-255| All reset

SPECIFICATIONS

ighting source	19 x RGBW 4in1 15W LED
A average Lifetime	50 000 hours
Dinner	0-100% linear curve
PAN	540° with fine control and position calibration and position auto-

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version.
Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal rm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:
LVD Directive 2014/35/EU :
EMC Directive 2014/30/EU :
RoHS 2 Directive 2011/65/EU
The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at : contact@algam.net