algam Lighting MS60 Moving Spot LED 60W Instruction Manual

MS60 Moving Spot LED 60W
Instruction Manual

(ES – NL user manuals also available, please contact: contact@algam.net)
Thank you for choosing one of our Algam Lighting product. Please read this user manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user guide for future reference.

SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products.
if one of those symbols is on your product , please read carrefully the following:
WARNING!
Before use, and before installing this fixture, read carefully user manual, and follow the safety precautions listed on this page.
WARNING!
Very high level light output. DO NOT LOOK INTO THE BEAM.
DANGER!
Hazardous voltage, Risk of electric shock!
ALWAYS disconnect the fixture from power for servicing, for cleaning or installing.
Do not connect this unit on a dimmer power pack.
Protect the unit from rain or moisture.

Locate the fixture in a well ventillated spot, away from flammable materials.
The fixture must be fixed at least 50cm from surrouding walls .
WARNING!
Burn Hazard. Do not touch. Very hot surface.
The fixture becomes hot during use and remains hot 10 min after use. Do not touch the unit.
WARNING!
Fire Hazard!
Keep flammable materials away from the fixture. Do not operate the fixture with ambient temperature over 4O°C.
DANGER!
Safety Hazard. Risk of injury.
This unit must be installed by professional people.
Please carefully read the instruction, which includes important information about the installation, usage and maintenance, BEFORE operating this device.

• This device is exclusively meant to be used as a splitter for DMX signals within the limits given in this manual. Using it in any other way you risk electric shock and warranty will become void.

• Never sever or manipulate the power cord or the plug. If a power cord is provided with an earth lead, this is mandatory to ensure safe operation! Otherwise a LIFE THREATENING situation exists!

• Unpack and check carefully there is no transportation damage before using the unit. Never put a damaged device into operation.

• Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit as stated in this manual.

• The unit is for indoor use only. Use it only in a dry location. Exposing the device to rain or moisture would cause the risk of electrical shock or fire.

• DO NOT let any liquids or objects enter the unit. Should any liquid be spilled on the unit, DISCONNECT the power supply to the unit immediately and contact the service company.

• The unit must only be installed in a location with adequate ventilation. Be sure that no ventilation slots are blocked.
  In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.

• Disconnect the device from the mains power before any servicing or maintenance.
  Notice regarding power disconnection: To disconnect the device from the power source the power plug must be removed from the power socket. For this reason the device must be placed in a position where a constant unobstructed access to the power socket is assured, thus in an emergency situation you are able to immediately pull out the power plug.
  To eliminate the risk of fire you must completely disconnect the power plug from the power socket after the device has been used.

• Always grasp the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this could result in a short circuit or an electrical shock. Do not place the device, speaker cabinets or anything else on the power cord and make sure that it does not become clamped.

• Before a storm and/or a thunderstorm with a risk of lightning, disconnect the device from the mains power supply.

• Under no circumstances may you open the device housing. Should you do so your safety would not be assured.
  There are no operational components whatsoever inside, only dangerous voltages that can give you a deadly shock!

• NEVER use the unit under the following conditions :> In places subject to vibrations or bumps.> In places with a temperature of over 45 °C or less than 2 °C.> In places subject to excessive dryness or humidity (ideal conditions are between 35% and 80%).

• Never submerse the device in water or any other liquid. Only wipe it with a slightly damp cloth.

• Never operate the device near flames, flammable, explosive materials, or hot surfaces. Otherwise you run the risk of causing a fire.

• Never leave this device running unattended.

• This appliance must not be used by individuals (including children) with restricted physical, physiological or intellectual abilities or deficiencies in experience and/or knowledge unless they are supervised by a person responsible for their safety or receive from this person instruction in how the appliance is to be used.

• Keep children away from the device and power cord! Children frequently underestimate the dangers of electrical devices. Also keep the plastic packaging well away from small children. There is a risk of suffocation!

• In the event of serious operating problems, stop using the unit immediately. Never try to dismantle, repair or modify the unit by yourself. Otherwise warranty becomes void. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance centre.

PRODUCT INSTALLATION

Power supply
Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device’ s power should be connected separately, so that device can be controlled individually. Cable spec.:

DMX connection
Connection between laser lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the attached 3 pin XLR plug/socket to connect the DMX output/input interface. The connection between socket and cable as below( note the plug/socket’ s 3 pin number and position). When using standard DMX512 contro! signal, the last device’ s output interface must be connected to a DMX plug. This plug is putting a 120 ohm resistance between “canon” plug’ s 2 pin and 3 pin.
Showing as below pic. Sticking this plug into the last device’ s signal output interface, it will avoid the nterference during the process of signal transmission.

RIGGING

Attention! The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected,  Certified installation materials should be used, the installed device should be inspected regularly for safety.
 Before rigging make sure that installation area can hold the 10 times weight of device.

OPERATION INSTRUCTIONS

NO| |
---|---|---
1| Keyboard| For value selection & menus navigation
2| Display| Display menu and values
3| Power supply Input| 110VAC – 240V AC power supply INPUT
4| Fuse holder| Protection fuse , replace with same value fuse
5| DMX input| DMX signal input – XLR 3 pin
6| DMX output| DMX signal Output – XLR 3 pin

MENU OPERATING INSTRUCTION

Mode Option, to choose the operating mode of laser.
Confirmation, to confirm the laser to show the present mode at the next operation.
UP/DOWN, to change operating mode, parameter or DMX address.

DMX PROTOCOL – 11 CHANNELS

DMX PROTOCOL – 13 CHANNELS

SPECIFICATIONS

Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose these materials with your normal household waste, but make sure that they are fed to a recovery. Please follow the notes and markings on the packaging.

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version.
Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
**** This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:
LVD Directive 2014/35/EU:
EMC Directive 2014/30/EU:
RoHS 2 Directive 2011/65/EU
RED Directive 2014/53/EU
LASERS directive : EN 60825-1:2014
The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at: contact@algam.net

Imported by ALGAM
2 Rue de Milan, 44470 Thouaré-sur-Loire, FRANCE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>